A-Neuvideo HD-88CT-A User manual

HD-88CT-A
8x8 HDMI-HDBaseT Matrix Switch with Audio and Extension
INSTRUCTION MANUAL
A-NeuVideo.com | Frisco, Texas 75034 | [phone] V.1.1

SAFETY INFORMATION
1. To ensure the best results from this product, please read this manual and all other documentation before operating your equipment.
Retain all documentation for future reference.
2. Follow all instructions printed on unit chassis for proper operation.
3. To reduce the risk of fire, do not spill water or other liquids into or on the unit, or operate the unit while standing in liquid.
4. Make sure power outlets conform to the power requirements listed on the back of the unit. Keep unit protected from rain, water and
excessive moisture.
5. Do not attempt to clean the unit with chemical solvents or aerosol cleaners, as this may damage the unit. Dust with a clean dry cloth.
6. Do not use the unit if the electrical power cord is frayed or broken. The power supply cords should be routed so that they are not
likely to be walked on or pinched by items placed upon or against them, paying particular attention to cords and plugs, convenience
receptacles, and the point where they exit from the appliance.
7. Do not force switched or external connections in any way. They should all connect easily, without needing to be forced.
8. Always operate the unit with the AC ground wire connected to the electrical system ground. Precautions should be taken so that the
means of grounding of a piece of equipment is not defeated.
9. AC voltage must be correct and the same as that printed on the rear of the unit. Damage caused by connection to improper AC
voltage is not covered by any warranty.
10. Turn power off and disconnect unit from AC current before making connections.
11. Never hold a power switch in the “ON” position.
12. This unit should be installed in a cool dry place, away from sources of excessive heat, vibration, dust, moisture and cold. Do not use
the unit near stoves, heat registers, radiators, or other heat producing devices.
13. Do not block fan intake or exhaust ports. Do not operate equipment on a surface or in an environment which may impede the normal
flow of air around the unit, such as a bed, rug, carpet, or completely enclosed rack. If the unit is used in an extremely dusty or smoky
environment, the unit should be periodically “blown free” of foreign dust and matter.
14. To reduce the risk of electric shock, do not remove the cover. There are no user serviceable parts inside. Refer all servicing to
qualified service personnel. There are no user serviceable parts inside.
15. When moving the unit, disconnect input ports first, then remove the power cable; finally, disconnect the interconnecting cables to
other devices.
16. Do not drive the inputs with a signal level greater than that required to drive equipment to full output.
17. The equipment power cord should be unplugged from the outlet when left unused for a long period of time.
18. Save the carton and packing material even if the equipment has arrived in good condition. Should you ever need to ship the unit,
use only the original factory packing.
19. Service Information Equipment should be serviced by qualifier service personnel when:
A. The power supply cord or the plug has been damaged.
B. Objects have fallen, or liquid has been spilled into the equipment.
C. The equipment has been exposed to rain
D. The equipment does not appear to operate normally, or exhibits a marked change in performance
E. The equipment has been dropped, or the enclosure damaged.
THIS SAFETY INFORMATION IS OF A GENERAL NATURE AND MAY BE SUPERSEDED BY INSTRUCTIONS CONTAINED WITHIN THIS MANUAL

1
TABLE OF CONTENTS
CONTENTS
INTRODUCTION .............................................................. 1
PACKAGE CONTENTS & FEATURES ........................... 2
SPECIFICATIONS ............................................................. 3
FRONT PANEL ..................................................................4
REAR PANEL ...................................................................7
TYPICAL APPLICATION ...................................................9
REMOTE CONTROL .......................................................12
IR EXTENDER ................................................................16
EDID FUNCTION ........................................................... 17
ETHERNET SERIAL INTERFACE ..................................22
RS-232 SERIAL INTERFACE .........................................23
INTRODUCTION
The HD-88CT-A is high-performance 8x8 matrix routing switcher
with eight (8) HDMI with DVI-Audio inputs and supports
simultaneously eight (8) HDMI with DVI-Audio and eight (8) CATx
outputs. The HD-88CT-A is based on HDBaseT technology and
that supports full resolution HDMI Video with embedded audio,
RS-232, and IR bi-directional, all over a single CATx cable. With a
signal bandwidth of 340Mhz, there is no signal degradation. High
Definition Digital signals can be selected and distributed to any 16
outputs simultaneously (8x channels x2). The Switcher is certified
as being fully CEC and HDCP 2.0 compliant, HDMI V1.4a 3D
formats, data rates up to 6.75 Gbps. Supports UXGA/WUXGA/DVI
1920x1200 resolution to any HD displays. The HD-88CT-A has
one CAT6/CAT6a and HDMI connector for each output, effectively
making this an 8x16 switcher (same signal on both outputs). 1 RJ-
45 connection on each output extends the HDMI signal to remote
location via HDBaseT CATx cable extend to HDBaseT Receiver.
The EDID can be selected between eight (8) different modes.
Control is provided via Front panel push buttons, IR remote or via
RS-232 or TCP/IP (not a web-browser). An RS-232 Windows GUI
interface is provided for matrix routing.
SAFETY PRECAUTIONS
Please read all instructions before attempting to unpack, install or
operate this equipment and before connecting the power supply.
Please keep the following in mind as you unpack and install this
equipment:
• Always follow basic safety precautions to reduce the risk of fire,
electrical shock and injury to persons.
• To prevent fire or shock hazard, do not expose the unit to rain,
moisture or install this product near water.
• Never spill liquid of any kind on or into this product.
• Never push an object of any kind into this product through any
openings or empty slots in the unit, as you may damage parts
inside the unit.
• Do not attach the power supply cabling to building surfaces.
• Use only the supplied power supply unit (PSU). Do not use the
PSU if it is damaged.
• Do not allow anything to rest on the power cabling or allow any
weight to be placed upon it or any person walk on it.
• To protect the unit from overheating, do not block any vents or
openings in the unit housing that provide ventilation and allow
for sufficient space for air to circulate around the unit.
DISCLAIMERS
The information in this manual has been carefully checked and
is believed to be accurate. We assume no responsibility for any
infringements of patents or other rights of third parties which may
result from its use.
We assume no responsibility for any inaccuracies that may be
contained in this document. We make no commitment to update or
to keep current the information contained in this document.
We reserve the right to make improvements to this document and/
or product at any time and without notice.
COPYRIGHT NOTICE
No part of this document may be reproduced, transmitted,
transcribed, stored in a retrieval system, or any of its part translated
into any language or computer file, in any form or by any means
— electronic, mechanical, magnetic, optical, chemical, manual, or
otherwise — without express written permission and consent
© Copyright 2011. All Rights Reserved.
Version 1.1 OCT 2013
TRADEMARK ACKNOWLEDGMENTS
All products or service names mentioned in this document may
be trademarks of the companies with which they are associated.

FEATURES & CONTENTS
Based on HDBaseT; bi-directional IR, RS-232, Multi format Audio, Ethernet and full resolution HD Video all, signals over CATx (6/6a/7) cable.
FEATURES
• 8x HDMI with DVI-Audio source devices matrix switched to 8x HDMI with (HDMI/DVI) SPDIF and 8x CATx(6/6a/7) Extender output devices.
• Application HDBaseT Specification for IR, RS-232, Multi Audio Format and HD Video Signals over CATx.
• HDMI digital Video w/embedded Audio, DVI format and CEC/HDCP 2.0 compliant
• Worldwide control EDID modes for HD Video resolutions.
• Link speeds of up to 6.75 Gbps (link clock rate of 340MbHz), Support HDMI 1.4a 3D formats.
• Wide range of HD resolutions from PC XGA to WUXGA 1920x1200 and HDTV/DTV HDMI resolutions 480i/480p, 576i/576p, 720p,
1080i & 1080p
• Compatible with all HDMI source devices, PC monitors, Plasma HD display, HDTV and audio receivers or audio amplifiers.
• Digital Video TMDS formats Resolution up to 1080P-60 with Deep color 36-bit.
• Digital Audio Support : - Dolby TrueHD, Dolby Digital, Dolby Digital Plug/ex, DTS, DTS-HD, DTS-HD Master, DTS-EX PCM, PCM2,
LPCM2
• Audio Input : Support DVI Audio.
• Audio Output : Support HDMI or DVI Audio with S/PDIF (LPCM 2-CH or Maximum 5.1CH)
• Various User Interface control:
• Windows based GUI control via RS-232 port
• Front Panel push button
• IR wireless remote control
• Ethernet Switcher control
• Third party RS-232 controller (via simple ASCII)
• Support world wide control functions: ALL/OFF/RECALL/ENTER/MEMORY/EDID/LOCK
• Support EDID modes: Embedded EDID modes: FSS/H24-3D/H24-3D-M/H36-3D/H36-3D-M/DVI-D 1280x1024-60Hz/ DVI-D
1920x1200-60Hz/AUTO
• External modes : Learning mode.
• Automatic scanning input & output status via LCM show on front panel.
• Support IR Remote and IR Extender with distance up to ~ 1000 ft. (300M) Max.
• EDID configuration via Internal modes.
• Consumer Electronic Control (CEC) switch all open or OFF
The Switcher will remember that last state during a power cycle.
When power is removed and resorted, the last configuration will be invoked
PACKAGE CONTENTS
1. HD-88CT-A Matrix Switcher
2. Operating Instructions
3. RS-232 V2.0 Protocol Instructions
4. Master wireless IR Remote Control (IR-HD88LA)
5. 8 each; Individual wireless IR Control (IR-HD88LA-IR01~IR08)
6. 19 inch Ear mount bracket (Part # 2U-440L)
7. HD-101 IR Extender distance 300M (1000 ft) Transmitter set.
8. HD-100 IR Extender distance 300M (1000 ft)Receiver set.
9. HD-101C IR Extender distance 2M(6ft) Transmitter Cable.
10. HD-100C IR Extender distance 2M(6ft) Receiver Cable.
11. CD Contents : This manual, Windows GUI, ISP V1.0 Windows driver
12. RS-232 Cable 6 feet (2M)
13. Worldwide Universal Power Supply 100~230 VAC, AC 50/60Hz, 10A
-- HD-6335R HDBaseT receivers sold separately. –
2

SPECIFICATIONS
SPECIFICATIONS
Type of HDMI Switcher: 8x HDMI inputs To 8x HDMI + 8x HDBaseT Outputs with Audio Matrix Switcher
HDMI Support: HD 1080p-@60Hz, H36-bit Deep color, 3D of HDMI V1.4a formats
HDCP / CEC Support: HDCP 2.0 Compliant, CEC Compliant.
Video Bandwidth: Double Data Rates: 340Mhz, Total 6.75Gbps bandwidth
Digital Video Support: HD: 480i / 480p / 720p / 1080i / 1080p up to 36bit deep color
Digital Audio Support: Multi Audio Formats 5.1 / 7.1, MAT(MLP) Dolby Digital, Dolby TrueHD, Dolby Digital Plus, DTS, DTS-ES 6CH,
DTS-HD, DTS-HD-HRA, DTS-HD Master, (PCM-2CH)
Inputs:
• 8x HDMI Sources
• 1x Audio (DVI Audio)
• 1x IR Ext. in ( Switcher control)
• 8x IR in (IR signal To 8x Rooms each - Via HDBaseT CATx cable)
• 1x ALL IR in (IR to Room - Via HDBaseT CATx cable)
• 1x RS-232 (Switcher control)
• 8x RS-232 (I/O To 8x Rooms - Via HDBaseT CATx cable)
Outputs:
• 8x HDMI Destinations
• 1x SPDIF (HDMI 5.1CH or DVI Audio)
• 8x CATx (HDBaseT Based via category 6/6a/7 cable)
• 1x ALL IR out (IR signals from Room - Via HDBaseT CATx cable)
• 8x IR out (IR signal from 8x Rooms each - Via HDBaseT CATx cable)
• 8x RS-232 ( I/O From 8x Rooms each - Via HDBaseT CATx cable)
Controls:
• 1x IR Remote Controller (remote switcher)
• 8x IR Room Remote Controller
• 1x IR External port x 1 (OD 3.5mm Ear phone Jack)
• 1x Select & Function buttons on front panel
• 1x RS-232 series interface (switcher control)
• 1x Ethernet series interface (switcher control)
Source Status: Automatically Scan Sources Inputs via LED show out
Function Control Key: ALL / OFF / RECALL / ENTER / MEMORY / LOCK / EDID
(8) EDID management: Select Embedded EDID :
• 1: FSS
• 2: H24-3D
• Mode3: H24-3D-M
• Mode4: H36-3D
• Mode5: H36-3D-M
• Mode6: DVI-D 1280x1024-60Hz
• Mode7: DVI-D 1920x1200-60Hz
• Mode8: AUTO
Infrared Frequency: 38 Khz
IR External Distance: ~1000 feet / 300 meters maximum
HDBaseT Extender Distance: ~300 feet / 100 meters maximum.
HDMI I/O Connector: HDMI Type A - SMD 19pin Female Type
Temperature: 32°F - 100°F Operation (0°C - 38°C)
Dimensions (LxWxH): 19 x 9.85 x 3.5 in (482mm x 250mm x 88mm)
Rack Mount: 2RU High 19 ”Rack Mount #2U-440L (with rack mount)
Power Supply: AC 100~240 VAC 50/60Hz (Power Consumption:10A Maximum)
Safety Approvals: CE, FCC, RoHS, REACH.
Product Weight: 4.75 Kgs / 7.91 lb
Note: Specifications are subject to change without notice.
3

4
FRONT PANEL
FRONT PANEL
1 POWER SWITCH
The power switch turns the unit on and off. The LCM will illuminate red to indicate that the switcher is ON and is receiving power.
The Switcher will remember that last state during a power cycle.
When power is removed and resorted, the last configuration will be evoked.
2INPUT STATUS DISPLAY
Input sources 1 to 8 LCM illuminates blue to indicate that a video source is present on that input.
3 OUTPUT STATUS DISPLAY
Each Output (destination) Channel shows which input (source) is assigned.
4 DESTINATION SELECT BUTTONS
Separate outputs 1 thru 8 select buttons are provided for each destination assignment.
Routing can be Source to Destination or one source to multiple destinations.
Example : Press Destination 1,3,5 then press Source 2 will route Input 2 to Output 1,3,5 respectfully.
5 EDID MODE SELECT BUTTONS
Used to select EDID mode using buttons #1 thru #2
6 IR SENSOR
The IR sensor receives IR commands from the supplied remote controller or third party IR emitter.
7 SOURCE SELECT BUTTONS
Separate inputs 1 thru 8 select buttons are provided each source selection.
15 19 INCH EAR MOUNT PAIR
Converts desktop to 19 inch rack mount. Bracket (part # 2U-440L) INCLUDED.
Image shows rack mount bracket attached.

5
FRONT PANEL
FRONT PANEL
8 FUNCTION KEY - ALL
Disables (mute) video on all destinations OR Selects the same source to all destinations.
Option 1
- Press ALL followed by OFF button. The display will show “ 0 “ indicating all destinations have no video selected.
Option 2
- Press ALL followed by Source 1 thru 8. The display will show the Source selected.
- Press ENTER The pre-set source selection will be assigned all destinations.
9FUNCTION KEY - OFF
Disables (mute) video to selected channels. Either destinations.
- Press OFF button followed by any Destination channel.
- Press 1 thru 8 output destination. The display will show “ 0 “ for the selected channel indicating no video selected.
10 FUNCTION KEY - ENTER
- Press ENTER to confirm entries.
11 FUNCTION KEY - LOCK
- Press and hold LOCK button for two seconds lockout the front panel.
- Press and hold LOCK button for two seconds to enable the front panel.

6
FRONT PANEL
FRONT PANEL
12 FUNCTION KEY - RECALL
The system will show previously stored presets, up to a total of 16.
Presets are stored in local memory using Source keys 1 thru 8 or Destination keys 1 thru 8 as the memory preset location.
- Press RECALL button.
- Press 1 thru 8 on either Source or Destination row.
- Press ENTER The pre-set configuration will execute.
Operation completes.
Operation will abort if no keys are pressed with 5 seconds.
13 FUNCTION KEY - MEMORY
The system will show store presets, up to a total of 16.
Presets are stored in local memory using Source keys 1 thru 8 or Destination keys 1 thru 8 as the memory preset location.
- Configure desired matrices.
- Press MEMORY button.
- Press 1 thru 4 on either Source or Destination row.
- Press ENTER to ready memory location.
- or press MEMORY again to cancel operation.
Operation completes.
Note : Operation will abort if no keys are pressed within 5 seconds.
14 FUNCTION KEY - EDID
- Press EDID to select new EDID mode or select source row #1 or #2 for LINK source EDID again.
- Press DESTINATION again, press the same DESTINATION # to learn CATx EDID, the EDID for CATx has been learned.

7
REAR PANEL
REAR PANEL
1DC POWER INLET
The Switcher is fitted with a AC power plug input connector.
Ensure that the used is of an approved type and is of sufficient
current carrying connector capacity with the correct voltage and
connector polarity. 100~240Volt AC, 50/60Hz power supply.
2 IR EXTENDER CONTROL
Support one of IR Extender. Extend distance maximum
300M / ~1000 feet. When you plug the External IR extender
into the switcher, the front panel IR receiver remain active.
3 RS-232 CONNECTION
RS-232 control port to allow for interfacing to a PC, Such as
a computer or touch panel control, to the switcher via this
DB-9pin Female connector for serial RS-232 control.
4 ETHERNET CONNECTION
ETHERNET control port to allow for TCP/IP interfacing to a
PC, Such as a computer or touch panel control (not a web-
browser),to the switcher via this RJ-45 Female connector to
control switcher.
5 OUTPUTS- 1,2,3,4,5,6,7 & 8 HDMI
Connect a signal link of HDMI direct digital video/audio
to this Female HDMI connector. This connector supports
HDMI digital video/audio and DVI digital video sources.
HDMI Digital Video/Audio, Connector with fix screw
Output 1 ~ Output 8
7 INPUTS- 1,2,3,4,5,6,7, & 8 HDMI
Connect a signal link of HDMI direct digital video/audio
to this Female HDMI connector. This connector supports
HDMI digital video/audio and DVI digital video sources.
HDMI Digital Video/Audio, Connector with fix screw
Input 1 - Input 8
Power Plug:
Power input - AC100~240V,50/60Hz, 10A
IR Extender Jack:
Female Jack - inner OD ᴓ3.5 mm
Remote port :
DB-9pin Female connector
Remote port : Control the switcher RJ-45
Female connector
HDMI digital video/audio connector:
HDMI Female connector.
Note: With the proper adapters, the switcher
can be used with DVI digital video signals
HDCP compliant. DVI does not support audio.
SPDIF: Use RCA connector with digital audio
signals output.
HDMI digital video/audio connector:
HDMI Female connector.
Note: With the proper adapters, the switcher
can be used with DVI digital video signals
HDCP compliant. DVI does not support audio.
Audio: Support the audio input when you use
DVI signals.
6
8

8
REAR PANEL
REAR PANEL
6RS-232- 1,2,3,4,5,6,7 & 8 CONNECTION TO CONTROL ROOM
8x RS-232 control port to allow for interfacing to a PC,
Such as a computer or touch panel control, to the switcher
via this DB-9pin Female connector for serial RS-232 control.
7OUTPUT - 1,2,3,4,5,6,7 & 8 HDBaseT
CAT Transmitter extend a signal link of HDMI / RS-232 / IR
Remote to this RJ-45 Female connector via CATX(6/6a)
category cable. Connector with RJ-45 Output 1 ~ Output 8
8IR REMOTE INPUT - 1,2,3,4,5,6,7 & 8 IR SIGNAL TO ROOM
Support eight of IR Extender to control signal to eight rooms
Extend cable distance maximum 300 M / ~1000 feet
When you plug the CAT5e/6/7 IR extender into the external
port, the room IR receiver remain active.
9IR REMOTE OUTPUT - 1,2,3,4,5,6,7 & 8 IR SIGNAL FROM ROOM
Support eight of IR Extender to receive signal from eight rooms
Extend cable distance maximum 300M / ~1000 feet. When you
plug the CAT5e/6/7 IR extender into the external port, the room
IR receiver remain active.
10 ALL IN : ALL HDBaseT IR REMOTE 1,2,3,4,5,6,7 & 8 (IR SIGNAL TO ROOM)
Support eight of IR remote signals to control to eight rooms via
ALL IN port. Extend cable distance maximum 300 M / ~1000 ft.
When you plug the CAT5e/6/7 IR extender into the external port,
the room IR receiver remain active.
11 ALL OUT : ALL HDBaseT IR REMOTE - 1,2,3,4,5,6,7 & 8 (IR SIGNAL FROM ROOM)
Support eight of IR remote signals from eight rooms via ALL OUT
port. Extend cable distance maximum 300M / ~1000 ft.
When you plug the CAT5e/6/7 IR extender into the external port,
the room IR receiver remain active.
Remote port :
DB-9pin Female connector
CAT connector:
RJ-45 Female connector.
IR Extender Jack:
Female Jack - inner OD ᴓ3.5 mm
IR Extender Jack:
Female Jack - inner OD ᴓ3.5 mm
IR Extender Jack:
Female Jack - inner OD ᴓ3.5 mm
IR Extender Jack:
Female Jack - inner OD ᴓ3.5 mm

TYPICAL APPLICATION
INSTALLING DIAGRAM
Sample connection using IR Transmitters (HD-101) and IR Receiver (HD-100) with HD-6335R & HD-88CT-A to control a projector.
NOTE:
1. IR Control Projector Over HDBaseT Extender:
HDBaseT Transmitter / HD-6335R HDBaseT Receiver
2. Projector RS-232 Control by a PC via CATx TX.
3. Projector IR control via CATx IR in (IR To projector).
4. IR Extender Transmitter (HD-101): Use HD-101 IR
Transmitter to Extend IR signal to Projector.
5. IR Extender Receiver (HD-100): Use HD-100 IR
Receiver to receive the Projector IR Remote signal.
9
HD-101
HD-6335R
HD-6335R
HD-100

TYPICAL APPLICATION
INSTALLING DIAGRAM
Sample connection using IR Transmitters (HD-101) with HD-88CT-A and HD-6335R to control a IR signal from Satellite Receiver.
NOTE :
1. IR Control Satellite Receiver Over HDBaseT
CAT5e/6/7 Extender from room:
HD-88CT-A HDBaseT CATx(6/6a/7) Transmitter
HD-6335R HDBaseT CATx(6/6a/7) Receiver
2. Destination RS-232 Control :
Via HD-5688CT TX RS-232 in
3. IR Extender Transmitter (HD-101):
Use HD-101 IR Transmitter to Extend IR signal.
Support HDBaseT Extender by HD-6335T Transmitter and HD-6335R Receiver via CATX(6/6a/7) cable.
10
HD-6335R HD-5609
HD-101

TYPICAL APPLICATION
INSTALLING DIAGRAM
Sample connection using Audio Extractor To Recode Audio (HD-5609) or to control ARC (HD-5610) and extend the HDMI signal via
HDBaseT Transmitter to IR Receivers (HD-6335R) with HD-88CT-A to extend 100M distance between switcher and destination.
NOTE :
1. Audio Extractor To Recode Audio : HD-5609 HDMI Audio Extractor.
2. Control HDMI ARC: HD-5610 ARC Control Box.
3. Switcher RS-232 Control Via a PC.
4. Switcher IR External port : Via HD-100 IR Extender Receiver.
5. HDMI Display : Signal from Blu-Ray or HD Satellite Receiver.
Application HDBaseT IR, RS-232, Multi format Audio and HD Video signals to pass over CATX(6/6a/7).
11
HD-5688CT IR
HD-100
IR Receiver
HD-5610
HD-5610

REMOTE CONTROL
Before making any connections to the switcher. Observe the following:
> Ensure the mains voltage supply matches the label on the
supplied plug-pack (+/- 10%)
> Ensure that the power switch is OFF
> Ensure that all system grounds (earth) are connected to a
common point.
> Avoid powering equipment within a system from multiple power
sources that may be separated by large distances
> Connect all audio video sources and destination equipment
> Power up all source and destination audio-visual sources
> For each destination output select the appropriate input source
by using the front panel input 1~8 select buttons. The supplied
IR remote control. Or through the RS-232 serial communications
port.
> Upon power up the switcher will return to its last used setting
before powered down.
REMOTE CONTROL
IR REMOTE CONTROL KEY :
1 2 SWITCH 1 POWER ON or OFF
Controller with a separate power ON and OFF
3DESTINATION : 1 thru 8 OUTPUT SELECTION
Press the destination button to select the output display channel.
4SOURCE : 1 thru 8 INPUT SOURCE SELECTION
Press input 1~8 sources with selection button
5 FUNCTION KEY
ALL - function selection button
OFF - function selection button
EDID - function selection button
RECALL - function selection button
MEMORY - function selection button
ENTER - function selection button
LOCK - function selection button
12

REMOTE CONTROL
IR REMOTE CUSTOM AND DATA CODES (NEC STANDARD)
HOW TO SETUP IR CODES :
Model number : HD-88CT-A
CUSTOM CODE : 09F6
POWER ON : 09F6 A15E
POWER OFF : 09F6 A25D
ALL : 09F6 B04F
OFF : 09F6 B14E
EDID : 09F6 B748
LOCK : 09F6 B54A
RECALL : 09F6 B24D
MEMORY : 09F6 B44B
ENTER : 09F6 B34C
PRESS DESTINATION then - # PRESS SOURCE - #
DESTINATION #1 : 09F6 10EF
DESTINATION #2 : 09F6 20DF
DESTINATION #3 : 09F6 30CF
DESTINATION #4 : 09F6 40BF
DESTINATION #5 : 09F6 50AF
DESTINATION #6 : 09F6 609F
DESTINATION #7 : 09F6 708F
DESTINATION #8 : 09F6 807F
SOURCE #1 : 09F6 01FE
SOURCE #2 : 09F6 02FD
SOURCE #3 : 09F6 03FC
SOURCE #4 : 09F6 04FB
SOURCE #5 : 09F6 05FA
SOURCE #6 : 09F6 06F9
SOURCE #7 : 09F6 07F8
SOURCE #8 : 09F6 08F7
For example;
Select Destination # 1 to show Source #1~8,
The IR Data Code list :
Destination # 1 , Source #1 09F6 10EF 09F6 01FE
Destination # 1 , Source #2 09F6 10EF 09F6 02FD
Destination # 1 , Source #3 09F6 10EF 09F6 03FC
Destination # 1 , Source #4 09F6 10EF 09F6 04FB
Destination # 1 , Source #5 09F6 10EF 09F6 05FA
Destination # 1 , Source #6 09F6 10EF 09F6 06F9
Destination # 1 , Source #7 09F6 10EF 09F6 07F8
Destination # 1 , Source #8 09F6 10EF 09F6 08F7
13

REMOTE CONTROL
ROOM REMOTE CONTROL #1 ~ #8 CUSTOM CODE AND DATA CODES
IR CUSTOM AND DATA CODES (NEC Standard)
PRESS Number To Select SOURCE
CUSTOM CODE : 09F6
IR-01 DATA CODE: IR-02 DATA CODE:
SOURCE #1 : 09F6 11EE
SOURCE #2 : 09F6 12ED
SOURCE #3 : 09F6 13EC
SOURCE #4 : 09F6 14EB
SOURCE #5 : 09F6 15EA
SOURCE #6 : 09F6 16E9
SOURCE #7 : 09F6 17E8
SOURCE #8 : 09F6 18E7
8x8 CATx SWITCHER 8x8 CATx SWITCHER
HD-5688CT-IR01 HD-5688CT-IR02
IR-03 DATA CODE: IR-04 DATA CODE:
SOURCE #1 : 09F6 31EE
SOURCE #2 : 09F6 32ED
SOURCE #3 : 09F6 33EC
SOURCE #4 : 09F6 34EB
SOURCE #5 : 09F6 35EA
SOURCE #6 : 09F6 36E9
SOURCE #7 : 09F6 37E8
SOURCE #8 : 09F6 38E7
8x8 CATx SWITCHER 8x8 CATx SWITCHER
HD-5688CT-IR03 HD-5688CT-IR04
14
SOURCE #1 : 09F6 21EE
SOURCE #2 : 09F6 22ED
SOURCE #3 : 09F6 23EC
SOURCE #4 : 09F6 24EB
SOURCE #5 : 09F6 25EA
SOURCE #6 : 09F6 26E9
SOURCE #7 : 09F6 27E8
SOURCE #8 : 09F6 28E7
SOURCE #1 : 09F6 41EE
SOURCE #2 : 09F6 42ED
SOURCE #3 : 09F6 43EC
SOURCE #4 : 09F6 44EB
SOURCE #5 : 09F6 45EA
SOURCE #6 : 09F6 46E9
SOURCE #7 : 09F6 47E8
SOURCE #8 : 09F6 48E7

REMOTE CONTROL
ROOM REMOTE CONTROL #1 ~ #8 CUSTOM CODE AND DATA CODES
IR CUSTOM AND DATA CODES (NEC Standard)
PRESS Number To Select SOURCE
CUSTOM CODE : 09F6
IR-05 DATA CODE: IR-06 DATA CODE:
SOURCE #1 : 09F6 51EE
SOURCE #2 : 09F6 52ED
SOURCE #3 : 09F6 53EC
SOURCE #4 : 09F6 54EB
SOURCE #5 : 09F6 55EA
SOURCE #6 : 09F6 56E9
SOURCE #7 : 09F6 57E8
SOURCE #8 : 09F6 58E7
8x8 CATx SWITCHER 8x8 CATx SWITCHER
HD-5688CT-IR05 HD-5688CT-IR06
IR-07 DATA CODE: IR-08 DATA CODE:
SOURCE #1 : 09F6 71EE
SOURCE #2 : 09F6 72ED
SOURCE #3 : 09F6 73EC
SOURCE #4 : 09F6 74EB
SOURCE #5 : 09F6 75EA
SOURCE #6 : 09F6 76E9
SOURCE #7 : 09F6 77E8
SOURCE #8 : 09F6 78E7
8x8 CATx SWITCHER 8x8 CATx SWITCHER
HD-5688CT-IR07 HD-5688CT-IR068
15
SOURCE #1 : 09F6 61EE
SOURCE #2 : 09F6 62ED
SOURCE #3 : 09F6 63EC
SOURCE #4 : 09F6 64EB
SOURCE #5 : 09F6 65EA
SOURCE #6 : 09F6 66E9
SOURCE #7 : 09F6 67E8
SOURCE #8 : 09F6 68E7
SOURCE #1 : 09F6 81EE
SOURCE #2 : 09F6 82ED
SOURCE #3 : 09F6 83EC
SOURCE #4 : 09F6 84EB
SOURCE #5 : 09F6 85EA
SOURCE #6 : 09F6 86E9
SOURCE #7 : 09F6 87E8
SOURCE #8 : 09F6 88E7

IR EXTENDER
REAR PANEL IR EXTENDER PORT
*** When you plug the External IR extender into the switcher, the front panel IR receiver remains active. ***
IR EXTENDER PACKAGE :
HOW TO SETUP THE IR EXTENDER TRANSMITTER & RECEIVER COMPONENTS
16
HD-100C
HD-100C
HD-100
HD-100C
HD-100
(HD-100C)
(HD-100C)
HD-100
HD-101 HD-100 HD-101
HD-100 HD-101
HD-100C
HD-101C HD-100C HD-101C
HD-100C HD-101C
HD-100C

EDID FUNCTION
EDID FUNCTION SETUP
EDID setup To change the EDID setup
Step 1. Press the EDID button The display will show the currently selected EDID mode
Step 2. Press SOURCE #1 or #2 button row The button will flash blue and the display will show the current Embedded EDID
Status.
Step 3. Press the ENTER button To set EDID mode.
The switcher will return to operation mode.
Operation will abort if no keys are pressed within 5 seconds.
Embedded EDID modes Total 8 EDID Modes
Embedded EDID setup
Press EDID > SOURCE > ENTER
SOURCE #1
or
SOURCE #2
To select Embedded EDID mode or LEARNING mode
Press EDID button : The LCM will show the current EDID status.
Repeatedly depressing the source 1 button will cycle up thru the options.
Repeatedly depressing the source 2 button will cycle down thru the options.
Select Embedded EDID :
Mode 1 : FSS
Mode 2 : H24-3D
Mode 3 : H24-3D-M
Mode 4 : H36-3D
Mode 5 : H36-3D-M
Mode 6 : DVI-D 1280x1024-60Hz
Mode 7 : DVI-D 1920x1200-60Hz
Mode 8 : AUTO
RESET EDID Return To Factory default
How to RESET EDID mode
Press EDID > RECALL > ENTER
RESET To the FACTORY DEFAULT (1080p-2CH).
Press EDID button : The LCM will show the current EDID status.
Press RECALL button : The LCM will show the RESET EDID.
Press ENTER to confirm entries.
The EDID will return to FSS mode and resolution 1080p-2CH.
17

EDID FUNCTION
LEARNING EDID Learning EDID from Destination to Source
Learning EDID setup
Press
EDID > DESTINATION > SOURCE > ENTER
Press EDID > DESTINATION Button. The LCM will be show LEARNING.
Switcher will LEARN destination HDMI EDID and pass the selected source.
Learning EDID setup for CATx
Key Press Sequence:
EDID > DESTINATION # > SOURCE # > ENTER
The EDID for HDMI has been learned
Press
EDID > DESTINATION > DESTINATION >
SOURCE > ENTER
Switcher will LEARN destination CATx EDID and pass the selected source.
Learning EDID setup for CATx
Key Press Sequence:
EDID > DESTINATION # > DESTINATION # > SOURCE # > ENTER
Again, Press the same DESTINATION # to learn CATx EDID The EDID for
CATx has been learned
NOTE : The already learned EDID cannot be modified. You can only rebuild a new Learning EDID.
For example:
When the Source has “Learned” the EDID data from a destination, It will save that EDID information into EPROM and the EDID data
cannot change. Please select new learning destination to sources or change to one of the embedded EDID modes when you want to
remove the learning EDID memory from EPROM.
18