AAFIRST AquaPoint 60 User manual

Installation Instructions For
AquaPoint 60
Bottled Water Cooler
PRODUCT CODE: WCBC60
PRODUCT NAME: AquaPoint60

To keep the best working condition and guarantee long life, read this manual carefully before you operate this
equipment.
1. Main Parts
No.
Name
No.
Name
1
2
3
4
5
6
7
8
9
Water Guard
Cold Water Faucet
Ambient Water Faucet
Drip Tray
Bottom Panel
Cold Water Temp. Controller
Rear Control Panel
Cold Water Switch
Drain Cap
10
11
Wire Condenser
Power Cord

2. Product Specifications
Product Name
Cold/Ambient Bottled Water Cooler
Product Code
WCBC60
Product Name
AquaPoint60
External Dimensions (W x D x H)
326 x 353 x 1032
Weight
Abt. 15Kg
Compressor
1/13 ~ 1/17HP Sealed Type
Condenser Type
Wire Type
Motor Power Consumption
90W
Refrigerant
R-134a
Cold Water Tank
STS304, 1.9Liters (Cold water only)
Cold water Capacity
20 Cups at 12℃ Under
Temperature Control
Thermostat (in Cold)
Cooling Type
Forced Cooling Type
Regulated Power
AC 220~240V/50~60HZ.1
Power Cord Length
1.8M
Front Panel
ABS
Side Panel
EGI
Faucet
PP Assembly
3. Safe Installation
Precautions during Installation
Use power cable of proper capacity.
The plug should be rated for more than 12A
Sharing a socket with other electrical products
will overheat the outlet and may cause fire.
Place Cooler on a hard, level surface.
Avoid placing the Cooler near a source of heat
or steam, such as a gas range or oil stove, or
near sink or other place where water may be
splashed onto the Cooler.
Maintain at least 15cm distance between wall
and back of the Cooler to allow for a good air
flow.
Transport & Installation
·Do not tilt the Cooler more than 45 degrees while moving it.
·Do not connect the Cooler to power for at least one hour after moving it.
·Always fill with water first, before switching power ON to avoid damaging the Cooler.

4.Commissioning the Cooler
⚫Commissioning
1. Sanitise/Clean the Cooler –especially the inside of the cold tank.
2. Carefully lift the bottle onto the Cooler. Avoid water spillage into the Cooler which could cause electric short cuts and
electric shock.
3. Allow water from the bottle to drain into the tank before switching power ON. It should take about 30 minutes to chill
the water from 30℃ incoming to 5℃.
⚫No-Spill Guard
Peel hygiene label off water bottle. Place the bottle on the Cooler’s No-Spill Guard.
The stainless-steel Feed Tube pops the valve open and then holds it and re-seals it.
The valve reseals automatically when the bottle is removed. Even if the bottle is half full there should be
no leak!
5.Maintenance
⚫Always disconnect the Cooler from electricity before cleaning or working on it.
1. Never use detergent or chemicals harmful to health for cleaning.
2. Never spray water onto the Cooler. If necessary, just use a damp cloth to remove dust from surfaces and from the
condenser.
3. After cleaning the Cooler, make sure it is completely dry before switching power ON.
⚫If the Cooler will not be used for a prolonged period.
1. Completely drain water from Cold Water Tank through the drain nipple behind the front door.
Any remaining water will stagnate and grow bacteria.
2. Ensure that the Cooler is completely dry. Dampness can cause rusting.
3. Protect the Cooler during storage with a dust- and dirt cover.
4. When re-siting the Cooler sanitise it and follow installation instructions.
⚫Sanitising
Follow the Water Cooler Association (s) Guidelines as to the frequency and method of sanitising. If uncertain, request
information from your Supplier.

6. Quick Fault Finder
PROBLEM
POSSIBLE CAUSE
CORRECTIVE ACTION
Not working
1. Check electricity supply
2. Check electric cable
3. Check fuse
1. Confirm power is ON.
2. If necessary, change
cable
3. If necessary, change
fuse.
Not chilling
1. Insufficient airflow between back
of Cooler and wall.
2. Temperature of incoming water
is too hot
3. Thermostat setting is wrong.
1. Ensure at least 15 cm
distance from wall for
sufficient ventilation.
2. Incoming water
temperature should be
below 30℃
3. Adjust thermostat.
Vibration & other
noises
1. The Cooler sits on an uneven
floor.
2. Is touching other products.
1. Place the Cooler on a
hard, level floor.
2. Ensure that no other
products touch the
Cooler
Insert plug firmly
into the wall outlet
Do not connect
several plugs to
one socket

Distributed by:
Cedar House
Grange Farm
Long Lane
Newbury
RG14 2TF
PH: 44 (0) 1635 202489 FAX: [phone]
E-mail: [e-mail]
Website: http://www.aafirst.co.uk/