Aastra 9316CW User manual

9316CW Installation
and
User Guide
P0857798 04 E UG 9316 Page -3 Wednesday, April 12, 2000 3:13 PM

-2
9316CW ImportantTips
‰ Wait for at least two rings to allow the phone to identify a caller and
display the caller’s name and/or number. You will have to subscribe to
a Calling Line Identification service to take advantage of this feature.
‰ The 9316CW is able to make and receive calls even during a power
failure. Features such as the display and memory keys will not work
without power.
‰ To call back local calls from the Callers List, be sure to remove the area
code.
‰ To use the Call Waiting Identification feature, you must subscribe to a
Call Waiting Identification service from your local telephone company.
‰ Some memory keys may be factory pre-programmed, and cannot be
programmed by the user.
Remember that there is a 24 digit limit on numbers and a 16 character limit
on names stored in the Directory.
P0857798 04 E UG 9316 Page -2 Wednesday, April 12, 2000 3:13 PM

Table of Contents
Introduction 1
Key Descriptions 2
The Set Options list 3
Basic Installation 4
Connecting the handset cord 4
Connecting the line cord 4
Connecting an optional fax
machine or modem 4
Connecting the power adaptor 4
Checking your telephone 5
Desk Mounting 5
Optional Wall Mounting 5
Adjusting the Display 5
The Set Options Key 5
Basic Features 6
Making a call 6
Answering a call 6
Making a Handsfree call 7
Putting a call on mute 7
Using the Redial List 7
Super Call Waiting Identification
= 8
SuperFlash 9
Turning the display of Call Waiting
Identification on or off 10
Changing the display language 10
Setting the date and time 10
Turning the ringer on or off 11
Setting ring tone and ringer volume 11
Controlling the ringer volume 11
Controlling the receiver volume 11
Controlling the speaker volume 11
Directory 12
Saving numbers and names to the
Directory 12
Saving an active call into Directory 12
Saving a memory key entry to the
Directory 13
Entering Names 13
Making a call from the Directory 13
Finding items in the Directory 14
Editing in the Directory 14
Deleting items from the Directory 14
Callers List 15
Using the Callers List 15
Setting up the Callers List 15
Finding an item in the Callers List 15
Making a call from the Callers List 15
Editing in the Callers List 16
Saving Callers List numbers to the
Directory or a Memory key 16
Deleting from the Callers List 17
Memory keys 17
Saving numbers and names in
memory keys 17
Saving from the display into
memory keys 17
Labeling the memory keys 18
Making calls from memory keys 18
Editing memory keys 18
Deleting memory keys 19
Saving features in memory keys 19
Using feature keys 19
Saving a feature and light in
memory keys 20
Using FeatureLight keys 20
Advanced Features 21
Adding a timer key 21
Using the call timer 21
Deleting a timer key 21
Selecting the dial pad mode 21
Entering area codes 22
The Security Numbers feature 23
Display messages and lights 24
The Callers List screen 24
Knowing when you have
a Voice Mail message 24
Clear Message Waiting 24
General display messages 25
Callers List display messages 26
Learning about the lights 27
Set indicator light messages 27
Handsfree indicator light messages 27
Viewing multiple display and light
messages 27
Troubleshooting 28
Index
P0857798 04 E UG 9316 Page -1 Wednesday, April 12, 2000 3:13 PM

P0857798 04 E UG 9316 Page 0 Wednesday, April 12, 2000 3:13 PM

1
Introduction
Thank you for purchasing 9316CW telephone. We think you’ll find it’s full of exciting
features. With a personal Directory and a Callers list, your new telephone is designed to
take full advantage of the latest services offered by your local telephone company.
When you subscribe to services such as Calling Line Identification and Call Waiting Iden-
tification
†
through your local telephone company, your 9316CW will show you all the
caller information you’ll need on its three-line back-lit display. For example, before you
even answer a call you’ll know who is calling, even if it’s a Call Waiting call. And Call
Waiting Identification information can appear on two telephone extensions at the same
time so that someone at either extension can initiate the switch to a Call Waiting call.Your
telephone will also tell you how many new callers you have.
You can set up a personal Directory in which you can enter up to 50 names and numbers,
and your Callers List will log up to 50 incoming calls. The Options List makes it easy for
you to personalize your telephone, and the back-lit three-line display provides walk-
through prompting that makes all of the many features and options even easier to custom-
ize. Please read on for more information on the many features of your 9316CW.
†
The names of these services may vary from area to area.
P0857798 04 E UG 9316 Page 1 Wednesday, April 12, 2000 3:13 PM

2
Key Descriptions
∆ Cycles through eight settings to adjust the display contrast.
¢ Allows you to store and access up to 50 numbers and names.
ß Stores numbers and names in the Directory and in memory keys.
ª Allows you to move up and down any list such as the Set Options, Direc-
tory, Callers List, or Redial List.
“ Allows you to backspace and erase when predialing and when adding or
changing numbers and names in the Directory, Callers List or in memory
keys.
‘ Adds a space when entering names in the Directory or in memory keys.
Allows you to view status messages on the display.
˙ Puts the call on hold, inserts a pause and shifts between upper and lower
case.
Volume bar
Dial pad
Handset
Number card and lens
Set Options
Down/up arrows
Sliding panel
Left/right arrows
Light
8 memory keys
Moveable display
Contrast
Callers
Delete
Rls
Hold
Link
Redial
Dial
Handsfree
Mute
Directory
Save
P0857798 04 E UG 9316 Page 2 Wednesday, April 12, 2000 3:13 PM

3
® Always hangs up a call. Also allows you to leave any list such as the Set
Options List, Callers List, Redial List or Directory.
≈ Allows you to access a list of people who called.
∑ Allows you to erase memory keys, delete single or all items in the Directory
and Callers List as well as the entire Redial List.
˚ Allows you to access network features such as Call Waiting. Link is also
referred to as Flash.
µ Allows you access to a list of the last five numbers you dialed.
∂ Dials any displayed number. Activates Handsfree mode if you have not
lifted the handset.
© Activates the Handsfree speaker and microphone so you can listen and talk
without lifting the handset. Also allows you to mute a handsfree call so that
a caller cannot hear you.
√ Allows you to adjust the receiver, speaker, and ringer volume.
∫ Memory keys store numbers, names, and features.
† The unlabeled Set Options key is hidden under the sliding panel and allows
you to access ten options to customize your telephone.
The Set Options list
Note : Please refer to each section for the default settings for the above options.
Set Options list page
01. Change display language 10
02. Set the time and date 10
03. Select the ring tone 11
04. Add a Timer key 21
05. Select the dial pad mode 21
06. Clear message waiting 24
07. Enter area codes 22
08. Set up the Callers List 15
09. Add Security Number 23
10. Call Waiting Identification display on or off 10
P0857798 04 E UG 9316 Page 3 Wednesday, April 12, 2000 3:13 PM

4
Basic Installation
This section explains how to install your 9316CW telephone.
Connecting the handset cord Connecting the line cord
Attach one end of the handset cord to the
handset and the other end to the handset jack. Attach one end of the line cord to jack number 1 and the other end of the line cord to the wall
jack.
Connecting an optional fax
machine or modem Connecting the power adaptor
Attach the line cord to jack number 2 and the
other end to the modem or fax machine. This
line cord is not supplied with the telephone.
Attach the power adaptor to the base of the
telephone where the warning symbol is
marked. Connect the power adaptor into the
closest electrical outlet.
To avoid potential electrical shock hazard to personnel or damage to the tele-
phone, use only the manufacturer-supplied equipment and installation proce-
dures.Specifically, use only 2 or 4 conductor modular teledapt plug/cords with
this product, and an AC transformer that is CSA/UL or CSA-NRTL/C approved
Class 2 level C, rated as follows:
For North American Markets mains nominal AC voltage 110-117V, Input: 110/
117VAC, 50/60Hz, 10W and Output: 16VAC 250mA.
For International Markets mains nominal AC voltage 220-240V, Input: 220/
240VAC, 50/60Hz, 10W and Output: 16VAC 250mA.
Substitution of non-approved equipment will void the Aastra Telecom Inc., war-
ranty.For more information call 1-800-574-1611.
1
2
1
!
P0857798 04 E UG 9316 Page 4 Wednesday, April 12, 2000 3:13 PM

5
Checking your telephone
When you plug in your 9316CW, you may see a message asking you to make a language
selection. Follow the directions on the display to select a language.
Your telephone also runs a test to ensure that the line cords are connected properly. If the
test fails, the display prompts you to check the line cord. Make sure that all connections
are fastened securely.
Note: The Ringer Equivalence Number (REN) is 1.4B for the 9316CW telephone. Please
see the base of your telephone or the Regulations sheet for more regulatory and
safety information.
Desk Mounting
Lower the stand into the slots on the base
of the telephone, as shown above. Slide the stand back until it clicks
into the locked position.
OptionalWall Mounting
†
Lower the stand into the slots on the base
of the telephone, as shown above.
†We recommend that you use a wall mounting plate which is available through your telephone company. If you are going to wall
mount your 9316CW, use the 20 cm (8”) line cord supplied with your telephone.
Slide the stand back until it clicks
into the locked position.
Adjusting the Display
Place your 9316CW on a table or hang it
on a wall, then adjust the display.
The Set Options Key
Move the sliding panel over to the
right to reveal the Set Options key.
P0857798 04 E UG 9316 Page 5 Wednesday, April 12, 2000 3:13 PM

6
Basic Features
Making a call
You can use the 9316CW to simply make a regular call, or you can predial a telephone
number to ensure it is correct before it is dialed out. Follow the procedures below to make
a regular or predialed call.
Note : If you have turned on the live dial pad option, you will not have to lift the handset
or press any buttons after entering the number. Refer to Selecting the dial pad
mode on page 21.
Answering a call
Calling Line Identification information is sent from the telephone company to your
9316CW telephone between the first and second ring. Therefore, if you want the telephone
number of the incoming call to appear on the display and in the Callers List, you must wait
until the information appears on the display before answering the telephone.
Putting a call on hold
When you put a call on hold it is important to hang up the handset.
Note: The 9316CW automatically releases the held call when a person on an extension
telephone picks up the call. If you don’t hang up the handset after you have put a
call on hold and that call is picked up by someone at another extension, the call is
taken off hold but remains connected to your telephone. If this happens, any back-
ground noise from your area will be heard by the caller and the person at the other
extension.
To make a regular call: To make a predialed call:
1. Lift the handset or press
©
. 1. Enter the number using the dial pad.
2. Enter the number using the dial pad. 2. Lift the handset or press either
©
or
∂
.
To answer a call:
1. Lift the handset or press
©
.
To put a call on hold and take a call off hold:
1. Make or answer a call.
2. Press
˙
.The display shows that the call is on hold.
3. Hang up the handset.
4.
To retrieve the call, lift the handset or press either
˙
or
© .
If you don’t retrieve the call within 15 minutes, the call is automatically dropped.
P0857798 04 E UG 9316 Page 6 Wednesday, April 12, 2000 3:13 PM

7
Making a Handsfree call
You don’t have to use the handset to use your telephone. Instead, you can use Handsfree
mode to place a call, or you can switch to Handsfree mode while a call is already in
progress.
Putting a call on mute
You can turn off the microphone so that the caller cannot hear you but you can still hear
the caller. Muting a call only works when you are in Handsfree mode.
Using the Redial List
The Redial List stores the last five numbers you dialed. When you press µ , the last
number you called appears on the screen.You can scroll through the list to view the other
numbers. Note that if you press µ after either lifting the handset or pressing
© , your telephone automatically dials the last number in the Redial list.
There may be times when you want to delete the contents of the Redial List. For example,
if you have dialed a personal number such as a password or your calling card number, you
may not want it to appear in the list where anyone can see it.
To dial without picking up the handset: To switch to a Handsfree call:
1. Press
©
.1. Lift the handset.
2. Enter the number using the dial pad. 2. Enter the number using the dial pad.
3. When the call is answered, press
©
.
4. Hang up the handset.
To mute a call:
1. Press
©
.
2. Without lifting the handset, make a call.
3. To turn the microphone off, press
©
again.You can hear your caller but your
caller cannot hear you.The light beside
©
flashes.
4. To speak to your caller, press
©
again. Each time you press
©
, you
switch between handsfree and mute.
5. When the call is over, press
®
.
To make a call from the Redial List:
1. Press
µ
.The display shows the last number you dialed.
2. Find the number you wish to call by pressing ª .
3. When the number is displayed, lift the handset or press either
©
or
∂
.
To delete the Redial List:
1. Press
µ
.
2. Press ∑ twice.The entire Redial List is deleted.
P0857798 04 E UG 9316 Page 7 Wednesday, April 12, 2000 3:13 PM

8
CallWaiting Identification
†
The 9316CW is capable of displaying Call Waiting Identification information of a second
incoming call while you have a call in progress. When you are on a call and you hear the
Call Waiting tone, the Call Waiting information is displayed as shown below.
If you decide you want to speak to the new caller, simply press ˚.Your first call will
not be disconnected.You may switch between callers as often as you like by pressing
˚. When you press ˚and see a caller’s Identification information but only
hear a dial tone, it means the caller has hung up. Your second call will be stored in the
Callers List even if it isn’t answered. For more information about stored calls, see Using
the Callers List on page 15.
Note: The Call Waiting Identification display option must be enabled in order to see the
Call Waiting Identification information on the display. Refer to Turning the display of
Call Waiting Identification on or off on page 10.
Super CallWaiting Identification✝
The Super Call Waiting Identification feature allows the 9316CW and one other Super
Call Waiting Identification compatible telephones to display identification information
about the second call at the same time as shown below.
†You must subscribe to your telephone company for the Call Waiting with Calling Line Identification service.
Incoming caller's information
(Caller One) is displayed.
CALLER ONE
555-1234
CALLER ONE
555-1234
When you hear the Call Waiting tone,
Caller Two's information is displayed.
CALLER ONE
555-1234
CALLER TWO
555-5678
Incoming caller's information
(Caller One) is displayed.
CALLER ONE
555-1234
CALLER ONE
555-1234
Extension telephone picks up and also speaks with Caller One.
Extension
CALLER ONE
555-1234

CALLER ONE
555-1234
>Extension in use


>Extension in use
Caller One

Call Waiting tone sounds and Caller Two's
information is displayed on both extensions.
Extension
CALLER ONE
555-1234
CALLER TWO
555-5678
CALLER ONE
555-1234
CALLER TWO
555-5678
P0857798 04 E UG 9316 Page 8 Wednesday, April 12, 2000 3:13 PM

9
SuperFlash†
The SuperFlash feature allows either of two telephone extensions to activate the link to a
Call Waiting call. When a person at either extension presses ˚, both extensions
switch to and speak with the Call Waiting caller as shown in the diagrams below.
Calls are not disconnected when you press ˚. If you wish to return to your first
caller press ˚again. The 9316CW and one other SuperFlash compatible telephone
extension will switch between the two callers each time you press ˚. Once you have
switched to one caller by pressing ˚, you must wait three seconds before you can
switch back to the previous caller. When you press ˚and see a caller’s Identification
information but only hear a dial tone, it means that the caller has hung up.
To end a call, ensure you can see that call’s Identification information (you may have to
press ˚), then press ®.
Note: SuperFlash and Super Call Waiting Identification only work with SuperFlash and
Super Call Waiting Identification compatible telephones.
†You must subscribe to your telephone company for the Call Waiting with Calling Line Identification service.
Incoming caller's information
(Caller One) is displayed.
CALLER ONE
555-1234
CALLER ONE
555-1234
Extension telephone picks up
and also speaks with Caller One.
Extension
CALLER ONE
555-1234
Extension in use
>
Call Waiting tone sounds and Caller Two's
information is displayed on both extensions.
Extension
CALLER ONE
555-1234
CALLER TWO
555-5678
CALLER ONE
555-1234
CALLER TWO
555-5678
CALLER ONE
555-1234
Either telephone can press ˚
to speakwith Caller Two.
Both telephones speak to Caller Two
and see the displayed information.
CALLER ONE
555-1234
Extension
Caller Two
Either telephone can press ˚again
to switch back to Caller One.
P0857798 04 E UG 9316 Page 9 Wednesday, April 12, 2000 3:13 PM

10
Turning the display of Call Waiting Identification on or off
You can choose whether or not Call Waiting Identification is displayed on your telephone.
Note: Turning the display of Call Waiting Identification on or off does not turn the feature
itself on or off. When the Call Waiting display is turned off, you will still hear the
Call Waiting tone when a Call Waiting call comes in, but the identification informa-
tion for the Call Waiting caller will not appear on your display screen. Contact your
local telephone company to subscribe or unsubscribe to Calling Line Identification
with Call Waiting Identification services.
Changing the display language
For changing business requirements, you may wish to change the language of your display
messages and prompts.
Setting the date and time
If you subscribe to the Calling Line Identification service from your telephone company,
the date and time are set automatically after you receive your first incoming call. If you do
not subscribe, you must set the date and time manually.
To resume the automatic date and time setting (if the date and time has been set manually),
disconnect the power supply, then re-connect it.After your first incoming call, the date and
time are automatically set.
To turn Call Waiting Identification on or off:
1. Press the Set Options key.
2. Use ª to scroll to number 10 or press ⁄‚ to go directly to the item.
3. Press •to turn the Call Waiting Identification display on or off.
4. Press ®.
To change the display language:
1. Press the Set Options key.
2. Use ªto scroll to number 1 or press ‚⁄ to go directly to the item.
3. Press •to change the language.
4. Press –until the display language you want appears on the display.
5. Press £to select the displayed language.
6. Press ®.
To set the date and time manually:
1. Press the Set Options key.
2. Use ªto scroll to number 2 or press ‚¤to go directly to the item.
3. Press •and follow the instructions on the display.
4. Press ®.
P0857798 04 E UG 9316 Page 10 Wednesday, April 12, 2000 3:13 PM

11
Turning the ringer on or off
Note: Do not lift the handset while you are turning the ringer on or off.
Setting the ring tone and ringer volume
You can choose one of four different ring tones and set the ringer volume.
Controlling the ringer volume
When the telephone is ringing, you can press the left or right side of the volume bar
√to adjust the ringer volume.
Controlling the receiver volume
When you are on the telephone, you can press the left or right side of the volume bar
√to adjust the receiver volume. When you have completed your call, the receiver
volume returns to default.
Controlling the speaker volume
When you are listening through the speaker, you can press the left or right side of the vol-
ume bar √to adjust the speaker volume.
To turn the ringer on: To turn the ringer off:
1. Press the right side of √. Con-
tinue pressing the right hand side until
you reach the desired ring volume.
1. Press the left side of √. Con-
tinue pressing the left hand side until
the ringer is off.
Ringer is OFF appears on the display.
To set the ring tone and volume:
1. Make sure that the ringer is turned on.
2. Press the Set Options key.
3. Use ªto scroll to number 3 or press ‚‹ to go directly to the item.
4. Press • and follow the instructions on the display.
When picking the ring tone, press √to adjust the volume.
5. Press ßto end when you are satisfied with ring tone and ringer volume.
Note:You cannot turn the volume off when you are choosing the ring tone.
6. Press ®.
P0857798 04 E UG 9316 Page 11 Wednesday, April 12, 2000 3:13 PM

12
Directory
The 9316CW stores the numbers and names of up to 50 of your business associates, cli-
ents, contacts, and friends in your Directory.You can dial these numbers by selecting
them.
Names are sorted alphabetically starting with their first character. (If you want your Direc-
tory sorted by the last name, enter the last name first.) If you do not enter a name, the item
is sorted by telephone number. The Directory items with only a telephone number are
numerically sorted at the beginning of the Directory.
Saving numbers and names to the Directory
Saving an active call into the Directory
To save a new number and name: To save from the display:
1. Press ß. 1. Ensure a number is on the display.
Choose a number from the Directory,
Redial List, or Callers List, or turn off
the Live Dial Pad option and press a
memory key.
2. Press ¢. 2. Press ß.
3. Enter the number using the dial pad. 3. Press ¢.If the name is displayed
with the number, both are now saved in
the Directory.
4. Press ß. Only the number is
stored at this point. 4. If no name is displayed, you are prompted to enter one.If you do not
want a name, go to step 5.To enter a
name, use the dial pad.(See Entering
Names on page 13.)
5. If you do not want a name, go to step
6.To enter a name, use the dial pad.
(See Entering Names on page 13.)
5. Press ß.
6. Press ß.
To save an active call:
1. Answer or make a call.
2. Press ß.
3. Press ¢.If the name was displayed with the number, both are now saved in the
Directory.
4. If no name is displayed, you are prompted to enter one. If you do not want to enter
one, go to step 5.To enter one, use the dial pad. (See Entering Names on page 13.)
5. Press ß.
6. Press ®.
P0857798 04 E UG 9316 Page 12 Wednesday, April 12, 2000 3:13 PM

13
Saving a memory key entry to the Directory
Entering Names
You can program names to correspond with numbers you have entered into the Directory
or a memory key. The following paragraphs explain how to enter letters using the dial pad.
Before you can use the dial pad to enter names, you must first save or edit a number in the
Directory or memory key.
To program a name, find the dial pad key that has the first character of the name. Keep
watching the display as you press the key until that character appears on the display. Press
a different dial pad key for the next character. If the next character is on the same key,
press ‘to move to the next space. To display upper case letters, press ˙, then
press the appropriate dial pad key. To insert a space, press ‘. To backspace and erase
a mistake, press “.
For example, to enter the name Ruth press these keys:
‡‡‡, °°, ‘, °, ››.
If you wish to change a digit or letter after you have entered it, press “to erase it.
⁄, - ’ & . ( ) 1 ¤a A b B c C 2 ‹d D e E f F 3
›g G h H i I 4 fij J k K l L 5 flm M n N o O 6
‡p P q Q r R s S 7 °t T u U vV 8 ·w W x X yY z Z 9
•* ‚0£#
Making a call from the Directory
To save a memory key entry into the Directory:
1. Press the desired memory key. Ensure the live dial pad option is turned off.
2. Press ß.
3. Press ¢.If the name was displayed with the number, both are now saved in the
Directory.
4. If no name is saved, you are prompted to enter one. If you do not want to enter a
name, go to step 5.To enter a name, use the dial pad.(See Entering Names on
page 13.)
5. Press ß.
6. Press ®.
To make a call from the Directory:
1. Press ¢.
2. Press ªor use the dial pad to find the item you want to dial out.
3. Lift the handset or press either ©or ∂.
4. To end the call, hang up the handset or press ®.
P0857798 04 E UG 9316 Page 13 Wednesday, April 12, 2000 3:13 PM

14
Finding items in the Directory
Editing in the Directory
Deleting items from the Directory
To find items in the Directory:
1. To see the Directory heading, press ¢.
2. To see the listings that start with a particular letter, press the appropriate dial pad key.
Then to see the other listings under that letter, press –. (For example: fitakes
you to the first "J" listing, then –takes you to the next "J" listing.fifitakes you
to the first "K" listing.) Use the letter chart shown previously.
OR, to move down and up the list, press –or ≠.If you want to scroll
steadily, press and hold –or ≠.
3. To leave the Directory at any time, press ¢or ®.
Note: If you are on a call while you are viewing the Directory, pressing ®also drops
the call.
To edit a number and/or name in the Directory:
1. Press ¢.
2. Press ªto find the item you want to edit.
3. To begin editing, press “.
4. If you do not want to change the number, go to step 5.To backspace and erase dig-
its, press “.To add digits, use the dial pad.
5. Press ß.
6. If you don’t want to change the name, go to step 7.To change or add to a name, use
“and the dial pad. (See Entering Names on page 13.) If you edit the wrong
item or want to quit without saving changes, press ¢or ®.
7. Press ß.
8. Press ®.
To delete individual items:
1. Press ¢.
2. Press ªto find the item you want to delete.
3. Press ∑twice.You are still in the Directory.
4. Press ®or ¢to exit the Directory at any time.
To delete all items:
1. Press ¢.
2. Press ∑.
3. Press ∑again to confirm deletion of the entire Directory.
4. Press ®.
P0857798 04 E UG 9316 Page 14 Wednesday, April 12, 2000 3:13 PM

15
Callers List†
Using the Callers List
The 9316CW stores up to 50 calls in the Callers List.Your telephone logs the number (and
name if available) of the caller, when they last called, and the number of times they tried to
reach you. See Callers List display messages on page 26 for a description of the display
messages and icons.
If the telephone number of the incoming call matches a number that you have programmed
with a name in a memory key or the Directory, the Callers List shows the name first and
then the number.You can choose to log either all incoming calls or only unanswered calls
in the Callers List.
Setting up the Callers List
You can program the 9316CW to record only unanswered calls or all incoming calls. The
default is to record all calls.
Finding an item in the Callers List
Making a call from the Callers List
If you call a number from the Callers List and you do not get connected, you may have to
edit the number (for example, the number may be long distance and you may have to add
“1”). See Editing in the Callers List on page 16.
†You must subscribe to your telephone company for the Calling Line Identification service.
To change the Callers List:
1. Press the Set Options key.
2. Use ªto scroll to number 8 or press ‚° to go directly to the item.
3. Press •to change the Callers List.
To find items in the Callers List:
1. To see the Callers List heading, press ≈.
2. To see the first new caller in the list, press –.
To move down and up the list, press ª.
If you want to scroll steadily, press and hold ª.
3. To leave the Callers List at any time, press ≈or ®.
Note: If you are on a call while viewing the Callers List, pressing ®drops the call.
To dial a number in the Callers List:
1. Press ≈.
2. Use ªto find the number you want to dial.
3. Lift the handset or press either ©or ∂.
4. To end the call, hang up the handset or press ®.
Note:When you finish the call, the display returns to the Callers List.
P0857798 04 E UG 9316 Page 15 Wednesday, April 12, 2000 3:13 PM

16
Editing in the Callers List
To have the Callers List show local numbers without the area code and internal numbers as
extensions, see Entering area codes on page 22.
Saving Callers List numbers to the Directory or a Memory key
To edit a number in the Callers List:
1. Press ≈.
2. Use ªto find the number you want to edit.
3. Press any key on the dial pad to begin editing.
4. To add digits, use the dial pad.To erase one digit to the right of the cursor, press
‘.To erase one digit to the left of the cursor, press “.
Caution:The Callers List does not save changes.If you plan to call the number
again, copy it to the Directory or a memory key.
5. To dial the edited number, lift the handset or press either ©or ∂.
To dial back a long distance number in the Callers List:
1. Press ≈.
2. Use ª to find the item you want to edit.
3. Using the dial pad, press ⁄and the area code if necessary.
4. To dial the edited number, lift the handset or press either ©or ∂.
5. If you want to save the number to the directory, press ß.See Saving numbers
and names to the Directory on page 12.
To copy a number from the Callers List to the Directory or to a memory key:
1. Press ≈.
2. Use ªto find the number you want to copy.
3. Press ß.
4. Press ¢or the memory key where you want to store the number.
5. If no name is displayed, you are prompted to enter one.To enter a name, use the dial
pad. (See Entering Names on page 13.) If you do not want to enter a name, go to
step 6.
6. Press ß.
7. To leave the Callers List at any time, press ≈or ®.
P0857798 04 E UG 9316 Page 16 Wednesday, April 12, 2000 3:13 PM