ABB ACS250 User manual

STANDARDS CONFORMITY
An ACS2250 fitted with this Option complies with the
Following standards:
CE-marked for Low Voltage Directive.
IEC 664-1 Insulation Coordination within Low Voltage Systems.
UL 840 Insulation Coordination for electrical equipment.
EN50081-2 EMC Generic Emissions Standard, Industrial Level.
EN50082-2 EMC Generic Immunity Standard, Industrial Level.
Enclosure ingress protection, EN60529 IP00, NEMA 250.
Flammability rating according to UL 94.
User Guide
All rights reserved. No part of this User Guide may be reproduced or
transmitted in any form or by any means, electrical or mechanical
including photocopying, recording or by any information storage or
retrieval system without permission in writing from the publisher.
© 2013 ABB Oy, ALL Rights Reserved
The manufacturer accepts no liability for any consequences resulting
from inappropriate, negligent or incorrect installation.
The contents of this User Guide are believed to be correct at the time of
printing. In the interests of a commitment to a policy of continuous
improvement, the manufacturer reserves the right to change the
specification of the product or its performance or the contents of the
User Guide without notice.
SAFETY
This option is specifically designed to be used with the ACS250
variable speed drive product and is intended for professional
incorporation into complete equipment or systems. If installed
incorrectly it may present a safety hazard. The ACS250 uses high
voltages and currents, carries a high level of stored electrical energy,
and is used to control mechanical plant that may cause injury. Close
attention is required to system design and electrical installation to avoid
hazards in either normal operation or in the event of equipment
malfunction.
System design, installation, commissioning and maintenance must be
carried out only by personnel who have the necessary training and
experience. They must read carefully this safety information and the
instructions in this Guide and follow all information regarding transport,
storage, installation and use of the Option module, including the
specified environmental limitations.
Please read the IMPORTANT SAFETY INFORMATION below, and all
Warning and Caution boxes elsewhere.
CAUTION
Store the Option in its box until
required. It should be stored in a
clean and dry environment.
Temperature range –40oC to
+60oC.
WARNING
The ACS250 and the Options
should be installed only by
qualified electrical persons and in
accordance with local and
national regulations and codes of
practice.
Electric shock hazard!
Disconnect and ISOLATE the
drive before attempting any work
on it. High voltages are present at
the terminals and within the drive
for up to 10 minutes after
disconnection of the electrical
supply.
Where the electrical supply to the
drive is through a plug and socket
connector, do not disconnect until
10 minutes have elapsed after
turning off the supply.
ACS250
RS485 3-Way Data Cable
Splitter RJ45
SAFETY NOTICES
WARNING is given where there
is a hazard that could lead to
injury or death of personnel.
CAUTION is given where there
is a hazard that could lead to
damage to equipment.
It is the responsibility of the
installer to ensure that the
equipment or system into which
the product is incorporated
complies with the EMC
legislation of the country of use.
Within the European Union,
equipment into which this
product is incorporated must
comply with 89/336/EEC,
Electromagnetic Compatibility.
ABB Oy
AC Drives
P.O. Box 184
FI-00381 HELSINKI
FINLAND
UK
www.abb.com/drives
Part No. 3AUA0000149995
Model No. RCRJ-01
Manual Part No. 82-485SP-ABB_V1
Document Part No. 3AXD10000273927
WARNING
Within the European Union, all
machinery in which this product
is used must comply with the
Machinery Directive
2006/42/EC, Safety of
Machinery. In particular, the
equipment should comply with
EN60204-1.

NOTES
COMMUNICATION INTERFACE
ACS250 RJ45 Port Connections
EXAMPLE OF CONNECTING THE RJ45 3-Way SPLITTER
RS485 3-Way Data Cable
Splitter RJ45
The RS485 3-Way Data Cable Splitter is an RJ45
1 to 2 way connection block.
The splitter can be used in typical applications where the
RJ45 communications port from an ACS250 is required to
be connected to more than one other drive or to other
suitable devices which utilise the RJ45 method of
connection.
Typical applications are where communication is required
from any of the following sources to multiple drives
forming a network:
oDrive Networks to Intelligent Controllers
oFieldbus Communication
oREMOTE PANEL
oPC to Drive Network via USB-RS485 Converter
For further details please refer to the ACS250 User manual.
Note:
This Option is suitable for use on all ACS250 Drives.
Part No. 3AUA0000149995
Model No. RCRJ-01
NOTES
82-485SP-ABB_V1
