ABB SM500F Use and care manual

—
ABB MEASUREMENT & ANALYTICS | INFORMATION | INF08/001 REV. C
SM500F
Field mountable videographic recorder
Door assembly replacement
INFORMATION
Door Assembly Replacement
N° INF08/001 Rev. B Product SM500F Color and Monochrome
Videographic Recorders
Manual IM/SM500F
1 Introduction
This publication details replacing an SM500F Videographic Recorder's door assembly. The procedure must
be carried out by a trained technician.
The contents of the replacement kits are shown in Table 1.1 (color display) and Table 1.2 (monochrome
display), respectively.
2 Tools Required
No. 2 Pozidriv screwdriver
T8 Torx driver
3 Door Assembly Replacement
1. Disconnect the recorder from the power supply.
Continued…
Description Part Number Qty
Door Assembly SM500/0052 1
Slotted Spring (Bissel) Pin B11344 2
Screw B12406 2
Information Sheet – Door Assembly Replacement INF08/001 1
Table. 1.1 Door Assembly (Color Display) Replacement Kit SM500/0722
Description Part Number Qty
Door Assembly SM500/0050 1
Slotted Spring (Bissel) Pin B11344 2
Screw B12406 2
Information Sheet – Door Assembly Replacement INF08/001 1
Table. 1.2 Door Assembly (Monochrome Display) Replacement Kit SM500/0723
Caution. The recorder is vulnerable to electrostatic damage. Wear an anti-static strap or place the
recorder on an anti-static workbench.

SM500F Color and Monochrome Videographic Recorders
Door Assembly Replacement 3 Door Assembly Replacement
2 INF08/001 Rev. C
2. Referring to Fig. 3.1:
a. Unlock the door with the key A, press the release catch Band open the door.
b. Remove the tamper-evident seal (if fitted), release the captive screw Csecuring the inner
cover plate and remove the plate.
c. Remove the two Torx screws Dsecuring the cable clamp and remove the cable clamp.
3. Referring to Fig. 3.2, disconnect the processor board flexi-cable from the motherboard.
Fig. 3.1 Removing the Cable Clamp
Fig. 3.2 Disconnecting the Processor Board Flexi-Cable
K
C
D
A
B

SM500F Color and Monochrome Videographic Recorders
Door Assembly Replacement 3 Door Assembly Replacement
INF08/001 Rev. C 3
4. Referring to Fig. 3.3, remove the slotted spring (Bissel) pins, remove the door assembly and place it
face down on the work surface.
5. Referring to Fig. 3.4, remove the 6 Torx screws Esecuring the door assembly rear cover and
remove the rear cover.
Continued…
Fig. 3.3 Removing the Door Hinge Pins
Fig. 3.4 Removing the Rear Cover
E

SM500F Color and Monochrome Videographic Recorders
Door Assembly Replacement 3 Door Assembly Replacement
4 INF08/001 Rev. C
6. Referring to Fig. 3.5, disconnect the keypad membrane cable Ffrom the processor board.
7. Referring to Fig. 3.6, remove the 4 Torx screws Gsecuring the display mounting plate and remove
the plate, complete with the display, ensuring that the keypad membrane cable clears slot Hin the
display mounting plate.
Fig. 3.5 Disconnecting the Keypad Membrane Cable
Fig. 3.6 Removing the Display Mounting Plate and Display
F

SM500F Color and Monochrome Videographic Recorders
Door Assembly Replacement 3 Door Assembly Replacement
INF08/001 Rev. C 5
8. Place the new door assembly face down on the work surface and, referring to Fig. 3.7, route the
keypad membrane cable Jthrough the slot in the display mounting plate and position the plate in
the door assembly.
9. Referring to Fig. 3.6, secure the display mounting plate to the door using the 4 Torx screws G.
10. Referring to Fig. 3.5, reconnect the keypad membrane cable F.
11. Referring to Fig. 3.4, refit the door assembly rear cover and secure it using the 6 Torx screws E.
12. Referring to Fig. 3.3, align the hinges on the door assembly with the hinge lugs on the case and
secure using the 2 slotted spring (Bissel) pins.
13. Referring to Fig. 3.2, reconnect the processor board flexi-cable to the motherboard.
14. Referring to Fig. 3.1:
a. Refit the cable clamp and secure it with the 2 Torx screws D.
b. Refit the inner cover plate, ensuring that lugs Kare located correctly in the slots in the case
and secure with the captive screw C. Refit the tamper-evident seal (if required).
c. Close and lock the door.
15. Restore the power supply to the recorder.
Fig. 3.7 Routing the Keypad Membrane Cable
J

INF08/001 Rev. C 11.2018
—
We reserve the right to make technical changes or modify the contents of this document
without prior notice. With regard to purchase orders, the agreed particulars shall prevail.
ABB does not accept any responsibility whatsoever for potential errors or possible lack of
information in this document.
We reserve all rights in this document and in the subject matter and illustrations contained
therein. Any reproduction, disclosure to third parties or utilization of its contents – in
whole or in parts – is forbidden without prior written consent of ABB.
© ABB 2018
—
ABB Limited
Measurement & Analytics
Howard Road
St. Neots
Cambridgeshire
PE19 8EU
UK
Tel: [phone]
Fax: [phone]
Email: instrumen[email protected]om
ABB Inc.
Measurement & Analytics
125 E. County Line Road
Warminster
PA 18974
USA
Tel: [phone]
Fax: [phone]
abb.com/measurement