ABB SAM600 Series Installation and operation manual

Grid Automation Products
SAM600 Process Bus I/O System
Engineering Manual

Document ID: 1MRK 511 431-UEN
Issued: June 2016
Revision: -
Product version: 1.1
© Copyright 2016 ABB. All rights reserved

Copyright
This document and parts thereof must not be reproduced or copied without written
permission from ABB, and the contents thereof must not be imparted to a third
party, nor used for any unauthorized purpose.
The software and hardware described in this document is furnished under a license
and may be used or disclosed only in accordance with the terms of such license.
Trademarks
ABB and SAM600 are registered trademarks of the ABB Group. All other brand or
product names mentioned in this document may be trademarks or registered
trademarks of their respective holders.
Open Source License Acknowledgements
This product incorporates open source software components covered by the terms
of third party copyright notices and license agreements. For more information,
refer to 1MRK 511 428-BEN SAM600 Product Guide.
Warranty
Please inquire about the terms of warranty from your nearest ABB representative.

Disclaimer
The data, examples and diagrams in this manual are included solely for the concept
or product description and are not to be deemed as a statement of guaranteed
properties. All persons responsible for applying the equipment addressed in this
manual must satisfy themselves that each intended application is suitable and
acceptable, including that any applicable safety or other operational requirements
are complied with. In particular, any risks in applications where a system failure
and /or product failure would create a risk for harm to property or persons
(including but not limited to personal injuries or death) shall be the sole
responsibility of the person or entity applying the equipment, and those so
responsible are hereby requested to ensure that all measures are taken to exclude or
mitigate such risks.
This document has been carefully checked by ABB but deviations cannot be
completely ruled out. In case any errors are detected, the reader is kindly requested
to notify the manufacturer. Other than under explicit contractual commitments, in
no event shall ABB be responsible or liable for any loss or damage resulting from
the use of this manual or the application of the equipment.

Conformity
This product complies with the directive of the Council of the European
Communities on the approximation of the laws of the Member States relating to
electromagnetic compatibility (EMC directive 2014/30/EU) and concerning
electrical equipment for use within specified voltage limits (Low-voltage directive
2014/35/EU). This conformity is the result of tests conducted by ABB in
accordance with the product standard EN 60255-26 for the EMC directive, and
with the product standard EN 60255-27 for the low voltage directive. The product
is designed in accordance with the international standards of the IEC 60255 series.

Safety information
Observe the following safety instructions when using the product.
Before first usage, read the product documentation in order to
ensure safe and reliable operation of SAM600 products.
Dangerous voltages can occur on the connectors, even though
auxiliary voltages are disconnected.
Each SAM600 product must be safely connected to ground using
the ground strap.
Only a competent electrician is allowed to carry out the electrical
installation.
Always follow national and local electrical safety regulations.
Non-observance of the safety information can result in death,
personal injury or substantial property damage.
Whenever changes in parameter settings are applied to SAM600
modules, take measures to avoid inadvertent tripping or malfunction
of connected protection and control devices.

Table of contents
SAM600 Process Bus I/O System 1
Engineering Manual
Table of contents
Section 1 Introduction ...................................................................3
1.1 This manual ......................................................................................3
1.2 Intended audience ............................................................................3
1.3 Related documents...........................................................................3
1.4 Document symbols and conventions ................................................4
1.4.1 Symbols..........................................................................................4
1.4.2 Document conventions ...................................................................4
Section 2 Engineering tool set .......................................................5
2.1 Introduction ......................................................................................5
2.2 SAM600 system engineering ............................................................6
2.2.1 SAM600 system configuration with PCM600..................................6
Section 3 Engineering process ......................................................9
3.1 SAM600 engineering process ...........................................................9
Section 4 Setting up a project .....................................................11
4.1 PCM600 projects............................................................................11
4.2 Connectivity packages and modules...............................................11
4.3 Building a plant structure ................................................................12
4.4 Instantiating a SAM600 system.......................................................14
4.4.1 Configuration wizard .....................................................................14
4.5 Inserting an SAM600 system in online mode ..................................15
4.6 Inserting a SAM600 system in offline mode.....................................18
4.6.1 Technical key................................................................................21
4.6.2 SAM600 serial numbers................................................................23
Section 5 SAM600 engineering ...................................................25
5.1 Parameter setting tool.....................................................................25
5.2 SAM600 SV stream and port configuration .....................................27
5.3 Composition upgrade tool ..............................................................32
5.4 Exporting and importing SCL files ...................................................33
5.4.1 Exporting SCL files from PCM600.................................................33
5.4.2 Importing SCL files to PCM600.....................................................35
5.5 Object properties ............................................................................37

Table of contents
SAM600 Process Bus I/O System2
Engineering Manual
5.6 Miscellaneous SAM600 tools ......................................................... 37
5.6.1 Get serial number ........................................................................ 37
5.6.2 Set time ....................................................................................... 37
5.6.3 Simulation mode.......................................................................... 38
5.6.4 Reset to factory default ................................................................ 39
5.6.5 Indicate module ........................................................................... 40
Section 6 Communication with PCM600 and SAM600 system ....41
6.1 Common write ............................................................................... 42
6.2 Common read................................................................................ 44
Section 7 Event viewer tool..........................................................47
Section 8 Glossary ......................................................................49
Appendix A SAM600 parameter settings.........................................51