Abexo MICRO-RGB Quick setup guide

Utilizzare la dima per segnare i punti di ssaggio alla parete. In base al
tipo di alimentazione disponibile, alimentare la scheda considerando,
in caso di alimentazione 12/24Vdc, il morsetto“COM” come morsetto
dove collegare il“meno”. Nel MICRO-TRAFFIC è presente un morsetto a tre poli:
comune + 2 poli per il collegamento indipendente della luce verde e rossa.
Use the template to mark the xing points on the wall. Based on the
available power, power the board considering, in case of 12/24Vdc
power the“COM”clamp as the clamp where you connect the“negative”.
In the MICRO-TRAFFIC is present a 3-pole terminal: one pole is shared, the other
2 are used for the independent connection of the green and red lights.
Utilisez le gabarit pour marquer les points de xation sur le mur. En
fonction de la puissance disponible, alimenter la carte en tenant compte,
dans le cas d'alimentation 12/24Vdc, la pince "COM" comme la pince où
vous connectez le "négatif".Dans le MICRO-TRAFFIC, il y a une borne à 3 pôles: un
commun et 2 pôles pour la connexion autonome de la lumière verte et rouge.
Verwenden Sie die Schablone, um die Befestigungspunkte an der Wand
zu markieren. Abhängig von der Art der Stromversorgung, speisen Sie
die Karte, wobei Sie im Falle einer 12/24Vdc Stromversorgung die
"COM" Klemme als eine Klemme betrachten, an der der negative Pol angeschlos-
sen werden soll. In der MICRO-TRAFFIC gibt es eine 3-polige Klemme: gemein-
sam + 2 Pole zum unabhängigen Anschluss von grünem und rotem Licht.
Usa el escantillón para marcar los puntos de jación en la pared. De
acuerdo con el tipo de fuente de alimentación disponible, alimente la
placa teniendo en cuenta, en el caso de la fuente de alimentación de
12/24 V CC, la terminal "COM" como un terminal donde conectar el "menos". En el
MICRO-TRAFFIC está presente un terminal tripolar: un polo es compartido, los
otros dos se utilizan para la conexión Independiente de las luces verdes y rojas.
MADE
IN
ITALY
cod. MICRO-00024
rev.0 - 10/2022
Istruzioni di montaggio e utilizzo
Assembly and use instructions
Instructions de montage et d'utilisation
Montage- und Gebrauchsanweisung
Instrucciones de montaje y uso
Guarnizione posteriore
Back gasket - Joint arrière
Hintere dichtung
Junto posterior
Cacciavite Compreso
Screwdriver Included
Tournevis inclus dans la boîte
Schraubenziehe enthalten
Destornillador oncluido
Grano
Grub screw
Vis sans tête
Gewindestift
Tornillo sin cabeza
70 mm
27 mm 16 mm
-RGB
RED GREEN BLUE
Alimentazione
Power supply
Alimentation
Versorgung
Alimentación
MAX assorbimento
MAX absorption
Absorption MAXI
Max. Leistungsbedarf
MAX absorción
(mA)
Luminosità min÷max (mcd)
Brightness min÷max (mcd)
Luminosité min÷max (mcd)
Helligkeit min÷max (mcd)
Brillo min÷max (mcd)
55
35
25
180 ÷ 350 450 ÷ 850 180 ÷ 350
24Vac +20% / -10%
24Vdc +/-20%
12Vdc +10% / -5%
code: APE-550/1038
MICRO-RGB
Guarnizione di tenuta
Impermeable gasket
Joint d'étanchéité
Dichtung
Junta impermeable
Lente diusiva
Diusive lens
Lentille de diusion satinée
Mattierter kunststo
Lente difundida Base
AB Tecno Srl
Via Cicogna 95 - 40068 San Lazzaro di Savena (BO)
Tel: [phone] - fax: [phone]
[email protected] - www.abtecno.com
Segnalatore luminoso RGB a LED
RGB led signalling light
Feu de signalisation RGB à LED
LED-RGB-Lichtanzeige
Luz de señalización rgb led
5
ANNI -YEARS
ANS - AÑOS
G
A
R
A
N
Z
I
A
*
*
*
*
W
A
R
R
A
N
T
*
*
*
*
G
A
R
A
N
T
I
E
*
*
*
*
G
A
R
A
N
T
Í
A
*
*
*
*
IP65
degree of
protection
Temperatura d’utilizzo: -20°C, +60°C
Operating temperature
Température de fonctionnement
Betriebstemperatur
Temperatura de uso

Tabella di selezione dei DIP SWITCH - In base ai collegamenti sui morsetti“-RED” e “-GREEN”si avranno combinazioni di led dierenti
Selection table of DIP-SWITCHES – According to the connections on terminals “-RED” e “-GREEN”the lights will light up in dierent color combinations
Tableau de sélection DIP-SWITCH – Selon les branchements aux bornes“-RED” et “-GREEN” les voyants s’allumeront avec diérentes combinaison de couleurs
DIP-SWITCH-Auswahltabelle – Nach den Anschlüssen an den Klemmen "-RED" und "-GREEN" wird die Lichtanzeige unterschiedliche LED-Kombinationen ergeben
Tabla de selección DIP-SWITCH – Según las conexiones a los terminales "-RED" y "-GREEN" las luces se encenderán con diferentes combinaciones de colores
DIP-SWITCH
COLORI LED / LED COLORS / COULEURS LED / LED-FARBEN / COLORES LED
INPUT Red
red / red INPUT Green green / green
INPUT Red
- / red INPUT Green green / - INPUT Red - / blue INPUT Green green / - INPUT Red - / red INPUT Green blue / - INPUT Red - / blue INPUT Green blue / - INPUT Red blue / blue INPUT Green blue / blue
SW1 - 1 ON
SW1 - 2 ON
SW1 - 3 ON
SW1 - 4
SW2 - 1 ON ON ON
SW2 - 2 ON ON ON
SW2 - 3 ON
ON
ON ON
ON
ON
ON
ON ON
SW2 - 4 ON ON ON
ON
ON
ON ON ON
ON
ON ON ON
DL1 DL2
DL1 DL2 DL1 DL2 DL1 DL2
INPUT
Red
INPUT
Red
INPUT
Green
DL1 DL2
INPUT
Red
INPUT
Green
DL1 DL2
INPUT
Red
INPUT
Green
INPUT
Red
INPUT
Green
INPUT
Red
INPUT
Green
INPUT
Green
DECLARATION OF EU CONFORMITY
Product: LED SIGNALLING LIGHT / Model: MICRO-RGB
Manufacturer: AB TECNO S.r.L. - Via Cicogna, 95 - 40068 San Lazzaro di Savena (BO)
The Manufacturer declares under its own responsibility that the product covered by the
declaration meets all the provisions applicable in the following Directives:
2014/35/EU - on the harmonization of the laws of the Member States relating to the
making available on the market of electrical equipment intended for use within certain
voltage limits.
2014/30/EU - for the harmonization of the laws of the Member States relating to electro-
magnetic compatibility and complies with the relevant harmonization legislation of the
Union: CEI EN 60947-1: 2008/A1: 2012/A2: 2015, CEI EN 60947-5-1: 2005/A1: 2010
Bologna, 01/02/2018 AB TECNO's CEO
Ulisse Pagani
Come richiesto dalla Direttiva 2012/19/CE concernente i Riuti di Apparecchiature
Elettroniche ed Elettriche (RAEE) è necessario: non smaltire i RAEE come riuti
municipali misti ed eettuare una raccolta separata di tali RAEE; rivolgersi al proprio
comune di residenza per informazioni circa i centri di raccolta separata per i RAEE.
Il presente simbolo a posto sul dispositivo elettronico, indica la raccolta dierenziata delle
apparecchiature elettriche ed elettroniche (Rif. Direttiva 2012/19/CE). L'adeguata raccolta
dierenziata per l'avvio successivo dell'apparecchio dismesso al riciclaggio, al
trattamento e allo smaltimento ambientalmente compatibili e contribuisce ad
evitare possibili eetti negativi sull'ambiente e sulla salute e favorisce il riciclo
dei materiali cui è composto il prodotto.
As required by the Directive 2012/19/CE concerning the Waste of Electronic and Electrical
Equipment (WEEE) it is necessary: to not dispose of WEEE as municipal mixed waste and
make a separate collection of such WEEE; contact your municipality of residence for informa-
tion about the separate collection centers for WEEE. This symbol on the electronic device
indicates the separate collection of electrical and electronic equipment (Ref. Directive
2012/19/CE). Appropriate separate waste collection for the subsequent start-up of
the disposed appliance to environmentally compatible recycling and treatment
and helps to avoid possible negative eects on the environment and on health and
favors the recycling of the materials to which the product is composed.
DIMA PER FORATURA
TEMPLATE FOR THE DRILLING
GABARIT DE PERÇAGE
SCHABLONE FÜR DIE DURCHBOHRUNG
ESCANTILLÓN PARA HORADAR
Cavo elettrico verso il basso
Electrical cable downwards
Câble électrique vers le bas
Stromkabel nach unten
Cablo elèctrico hacia abajo
Forare con punta Ø4
drill with Ø4 tip
percer avec pointe Ø4
mit Ø4 Spitze bohren
taladro con punta de Ø4
ALTO
TOP
HAUT
TOP
SUPERIOR
Scala 1:1
1:1 Scale - Échelle 1:1
Maßstab 1:1 - Escala 1:1 BASSO
BOTTOM
BAS
UNTERSEITE
FONDO
COLLEGAMENTI
CONNECTIONS
CONNECTIONS
VERBINDUNGEN
CONEXIONES
(- RED / + COM / - GREEN)
DIP-SWITCH 1 (SW1)
DIP-SWITCH 2 (SW2)