ABH 6000 Series User manual

NOTES
1. TRIM CAN BE MOUNTED UP, DOWN, HORIZONTALLY OR VERTICALLY.
2. USES STANDARD 161 DOOR PREP.
3. VISION LITE MUST BE AT LEAST 6" FROM CENTERLINE OF TRIM.
8
7
12
123
4PULL SIDE HANDLE ASSEMBLY
1
41/4-20 NUT W/ NYLON WASHER
LATCH
1
PUSH SIDE HANDLE ASSEMBLY
11/4-20 x 2-1/2" TRUSS HD. M.S.
48-32 x 3/8" FHMS
6COVER
2
8
1
2
4
3
6
7
5
QTY PART DESCRIPTIONITEM
#8 x 3/4" FHWS
2
PATENT No. 6,196,599
US
R
CL
LISTED
U
c 2017 ABH Mfg., Inc.
printed in USA
www.abhmfg.com
E-mail: [email protected]
Architectural Builders Hardware Mfg., Inc.
1222 Ardmore Ave., Itasca, IL 60143
630.875.9900; FAX 800.9FAXABH (932.9224)
O
R6000
REVISED 05-19-17
6000-1-14.DWG
VERIFY CORRECT BACKSET AND HORIZONTAL
OR VERTICAL MOUNTING BEFORE DRILLING.
THEN USE BACKSET TEMPLATE THAT IS SUPPLIED.
HORIZONTAL
BACKSET
WITH 7"
HANDLES
BACKSET
HANDLES
HORIZONTAL
WITH 5" OR 7"
DOWN
HANDLES
UP
HANDLES PUSHPULL HANDLES
MIXED
PULLPUSH
INSTALLATION INSTRUCTIONS:
1. Prep door according to latch backset and determine if trim is to be mounted horizontal or vertical mounting using backset template.
2. Install latch using either wood (item 5) or machine screws (item 2) depending on door type.
3. Install trim:
A) Test both handle assemblies to determine which is the push or pull type.
B) Select the pull handle assembly (item 8) first.
C) Place pull handle on pull side of the door and slide cam shaft into latch cam. Then place the push side handle assembly (item 4)
on the push side of the door. Slide push side cam shaft into latch cam. By hand, fasten both trim handles with (4) 1/4-20
machine screws (item 3) and (4) 1/4-20 hex nuts (item 7). Test both handles for free movement of the latch bolt before
tightening all screws. If latch bolt does not extend or retract freely because of any type of binding, loosen mounting screws to
adjust alignment of trim handles and re-tighten screws one at a time while checking latch bolt movement from both handles.
D) Test for proper operation and check that the mounting hardware (item 3) & (item 7) is tight before proceeding with the next step.
E) Place covers (item 1) over push and pull trims and secure with (2) 8-32 flat head screws (item 2) on each cover .
9
9REF SPRING
PIN & COTTER PIN
REF
10
CAM SHAFT
**
**
PAGE 1 OF 3
6
LATCH CAM
2
5
SQUARE
-OR-
ROUND
COVER
6000 SERIES INSTALLATION
ALL PREP MOUNTING HOLES
TO BE STRAIGHT & PARALLEL
TO ONE ANOTHER, THIS WILL
HELP PREVENT ANY BINDING
OF MECHANICAL PARTS.
10
NOTE:
BEFORE MOUNTING BASE ASSEMBLIES
CAM PIN MUST BE ROTATED TOWARDS
SIDE INDICATED BY ARROW STAMPED
ON THE BASE.
PUSH
CAM SHAFT
PULL
DETAIL "A"

c 2017 ABH Mfg., Inc.
printed in USA
www.abhmfg.com
E-mail: [email protected]
Architectural Builders Hardware Mfg., Inc.
1222 Ardmore Ave., Itasca, IL 60143
630.875.9900; FAX 800.9FAXABH (932.9224)
O
R6000-2-14.DWG
REVISED 05-19-17
PAGE 2 OF 3
6000
13/16"
BEVEL EDGE DOOR
UNIVERSAL OR
SQUARE EDGE DOOR
BORE
5-3/8"
4-3/8"
6-5/8"
8-5/8"
5/32"
1-1/8"
C
L
LOCK
&
STRIKE
BACKSET
13/16" 2-1/4"
7"
5"
2-3/4"
3-3/4"
BACKSET
DEPTH OF BORE
DOOR LATCH PROVISIONS
DEPTH
OF
BORE CHART
SEE DEPTH OF
1-1/8" DIA. (MIN)
DRILL FOR #8
WOOD SCREW
(2 PLACES)
1-3/4"
7/8"
2-1/4"
13/16"
13/16"
BACKSET
#8-32
TAPPED HOLE
(2 PLACES)
1-1/8"
1" DIA. HOLE REQUIRED, 2 PLACES
"HOLE" IN REINFORCEMENT
2-1/8" DIA.
HOLE THRU
5/32"
REINFORCEMENT BY
DOOR MFG.
7"
5"
2-3/4"
3-3/4"
BACKSET
UNIVERSAL OR
SQUARE EDGE DOOR
BEVEL EDGE DOOR
1" DIA. HOLE
(THRU ALL
SUPPORTS)
1-11/16"
3-3/8"
(4) 5/16" DIA.
HOLES BOTH SIDES
C
L
LOCK
&
STRIKE
WOOD DOORMETAL DOOR
EDGE GUARD NOTE:
WHEN PREPPING THE
DOOR FOR THE BACKSET,
DETERMINE IF THE DOOR
WILL RECEIVE AN EDGE
GUARD. IF SO, THE EDGE
GUARD SHOULD BE
INSTALLED FIRST AND
THEN THE PREP FOR THE
LATCH BACKSET SHOULD
BE MEASURED FROM THE
OUTSIDE EDGE OF THE
EDGE GUARD.
DOOR PREP INFORMATION:
1. BACKSET DIMENSION FROM LOW EDGE OF BEVEL.
2. CENTER PUNCH ALL HOLES.
3. DRILL HOLES (FOR HOLLOW METAL DOORS,
DO NOT DRILL THRU. CENTER PUNCH & DRILL
HOLES FROM BOTH SIDES OF DOOR).
4. REINFORCEMENT MUST BE APPLIED ON METAL
DOORS AT THE SCREW LOCATIONS.
5. REINFORCEMENT TO BE SUPPLIED BY DOOR
MANUFACTURER. THE HANDLE ASSYS MUST BE
SUPPORTED. THE LATCH BOLT UNIT MUST BE
SUPPORTED AND CENTERED WITHIN 1/16" OF
THE CENTERLINE AT THE BACK END.
ADA
RECOMMENDED
HEIGHT 44" FROM
FINISHED FLOOR
TO CENTER LINE
-OR-
CHECK LOCAL ORDINANCE
FOR PROPER HEIGHT
VERIFY BACKSET
CENTER LINE
6000 SERIES PUSH/PULL LATCH - DOOR PREP
1-3/4"
7/8"
2-1/8" DIA.
HOLE THRU
1-11/16"
3-3/8"
(4) 5/16" DIA.
THRU HOLES
USE PROVIDED
ORIGINAL FULL
SCALE
TEMPLATE TO PREP
THE DOOR
3-3/8"
1-11/16"
7/8" 1-3/4"
(4) 5/16" DIA.
THRU HOLES
HORIZONTAL MOUNTING
BACKSET
LOCK EDGE
OF DOOR
2-1/8" DIA.
THRU HOLE
(VERTICAL MOUNTING SHOWN
SEE BELOW FOR HORIZONTAL MOUNTING) (VERTICAL MOUNTING SHOWN SEE BELOW FOR HORIZONTAL MOUNTING)

3/32"
DOOR STOP
MORTAR
GUARD
3-3/8"
(MIN)
1" (MIN)
REINFORCEMENT BY
FRAME MFG.
HALF DOOR THICKNESS
(MEASURED FROM STOP OR
SILENCER WHEN USED)
C
LLOCK & STRIKE
1-1/4"
+1/64
-0
1-1/16"
2-1/16"
2-1/16"
4-7/8"
3-3/8"
3-3/8"
+1/64
-0
#12-24
TAPPED HOLE
(2 PLACES)
LOCK
&
STRIKE
L
C
1" X 1-1/2" MIN CAVITY TO
ACCOMMODATE DUST BOX
C
L
LOCK
&
STRIKE
DRILL FOR #8
WOOD SCREW
(2 PLACES)
L
C
3/32"
27/32"
1-1/2"
1-1/8"
1-1/16"
1-1/16"
2-3/4"
HALF DOOR THICKNESS
(MEASURED FROM STOP OR
SILENCER WHEN USED)
c 2017 ABH Mfg., Inc.
printed in USA
O
Rwww.abhmfg.com
E-mail: [email protected]
Architectural Builders Hardware Mfg., Inc.
1222 Ardmore Ave., Itasca, IL 60143
630.875.9900; FAX 800.9FAXABH (932.9224) REVISED 05-19-17
6000-3-14.DWG
PAGE 3 OF 3
6000
WOOD FRAMEMETAL FRAME
THICKNESS
3. Mortise to required strike and box depth.
2. Center strike and mark screw positions.
1. Mark centerline of latch bolt on frame.
1-1/4
1-1/4
1-1/23-3/8 4-7/8
4-1/8
3/32
1/4
1/4 5/64
1-5/16
1-1/8 9/16
2-3/4
2-1/8
OF LATCH
L
C
(OR SILENCER)
EDGE OF STOP
1/2 DOOR
4. All dimensions in inches.
1/32
15/16
4-3/4
1-5/32
4-1/8
3-1/4 3-3/16
1"
1/16
3/16
1-11/16
1/2
PREP FOR #8 SCREW
1-3/16
2-1/4
1-11/16
1
1
1-11/16
1/2
1-3/16
3/16
1/16
9/64
2-1/4
1-11/16
1/32
9/16
1-3/16
1-5/32
61/64
2-1/8
2-11/16
1-1/4
PREP FOR #8 SCREW
PREP FOR #8 SCREW
1"
(2) TAP #12-24
1-1/2"
DOOR STOP
6000 SERIES PUSH/PULL LATCH - FRAME PREP
(ASA STRIKE SHOWN FOR EXAMPLE) ("T" STRIKE SHOWN FOR EXAMPLE)
LOCK & STRIKE
ASA STRIKE & DUST BOX "T" STRIKE & DUST BOX "D" STRIKE
601LB STRIKE
FRAME PREP: