Gantner GAT NET.Lock 7020 System Quick guide

www.gantner.com HB_GAT-NETLOCK7020--EN_12 1
GAT NET.Lock 7020 System
Electronic RFID Locker Locks
Installation, Configuration, Operation
Document Version 1.2

GAT NET.Lock 7020 System
www.gantner.com HB_GAT-NETLOCK7020--EN_12 3
©
Copyright 2019 GANTNER Electronic GmbH
Operating instructions, manuals and software are protected by copyright. All rights are reserved. Copying, duplication, translation,
installation in any electronic medium or machine-readable form in whole or in part is prohibited. The sole exception is represented
by creation of a back-up copy of software for own use as a safeguard, so far as this is technically possible and recommended by us.
Any infringement will render the party committing such infringement liable to compensation payment.
Liability
Any claims against the manufacturer based on the hardware or software products described in this manual shall depend exclusively
on the conditions of the guarantee. Any further-reaching claims are excluded, and the manufacturer accepts no liability for the
completeness or accuracy of the contents of this manual. The right is reserved to make alterations, and alterations may be made at
any time without prior notice being given.
Trademarks
Attention is drawn at this point to markings and registered trademarks used in this manual. All product and company names, which
are mentioned in this manual, are only used for identification and explanation purposes. Some of these names may be trademarks
or registered trademarks of the corresponding company.
Contact
The contact information for questions regarding the GAT NET.Lock 7020 or for general enquiries is listed below:
Contact address of manufacturer:
GANTNER Electronic GmbH
Bundesstraße 12
6714 Nüziders, Austria
www.gantner.com/locations

GAT NET.Lock 7020 System
4 HB_GAT-NETLOCK7020--EN_12 www.gantner.com
Important Information
Dear Customer,
Our aim is to ensure that our product operates with safety and to your complete satisfaction. To achieve this aim, please take
this opportunity to familiarize yourself with the following guidelines.
- Pay attention to the safety messages in this manual. The messages are indicated by the signal words
"DANGER", "WARNING", or "CAUTION", and inform you about hazardous situations and how to avoid them.
- Pay attention to messages indicated by the "NOTICE" signal word. These messages include important
information for avoiding property damage.
- Pay attention to the symbols and safety messages on the product.
- Read all instructions in this manual carefully before installing or operating the product.
- Where not otherwise specifically documented, the appropriate installation, commissioning, operation and
maintenance of the product is the customer’s responsibility.
- Keep this manual in a safe place for quick reference.
Notation of Safety Information and Safety Symbols
This manual includes important safety messages and symbols intended to inform the user about potentially hazardous situations
or important information for the safe and proper use of the described product(s). The safety messages also include directives on
how to avoid hazardous situations. These safety messages and directives must be read and observed.
The structure of the safety messages and the meaning of the symbols used in this manual are described in this section.
1. Safety Messages for Personal Injury
Personal safety messages contain a signal word, describe the nature of the hazard, and indicate how to avoid the hazard.
The safety alert symbol used without a signal word always precedes important safety information that must be read
carefully, and the instructions carefully observed. Not doing so may cause personal injury.
Format of safety messages that apply to an entire section:
These safety messages may be used with or without a symbol.
Electrical shock
➔Touching current-conducting parts may result in injury due to electrical shock.
- Do not remove safety protection and covers.
- Do not touch the electrical connections while power is being supplied.
Format of safety messages that are embedded in text and apply to a specific point:
CAUTION! Electrical shock. Never remove safety protection and covers. Do not touch the electrical connections while
power is being supplied.

GAT NET.Lock 7020 System
www.gantner.com HB_GAT-NETLOCK7020--EN_12 5
2. Property Damage Messages
Property damage messages are used to describe potentially hazardous situations that may lead to property damage. These
messages have the same layout as safety messages but use the signal word "NOTICE" instead of “CAUTION”.
Format of property damage messages that apply to an entire section:
Risk of damage to the device and connected devices
Risk of malfunction
- Read the following instructions carefully before installing the device.
- Always adhere to the instructions.
Format of property damage messages that are embedded in text and apply to a specific
point:
NOTE! Risk of damage to the device and connected devices. Read the following instructions carefully before installing the
device.
3. Definition of the Signal Words
Indicates a hazardous situation that, if not avoided, may result in minor or moderate injury.
Indicates information considered important, but not hazard-related (e.g., messages relating to
property damage).
4. Definition of the Safety Symbols
Caution: General Information
This symbol indicates general warnings or cautions that are not related to a particular type of hazard.
Caution: Electrical Shock
This symbol indicates warnings related to electrical hazards (danger due to high voltage).
Prohibited: Do Not Disassemble
This symbol indicates warnings about not disassembling certain components or equipment. Disassembling may
lead to damage or malfunction of the device.
Mandatory Action: General Information
This symbol indicates general information that must be read and followed before proceeding with the
accompanying instructions.
Mandatory Action: Read Instructions
This symbol indicates information referring to an important description in the manual, or other documentation,
which must be read and followed.

GAT NET.Lock 7020 System
6 HB_GAT-NETLOCK7020--EN_12 www.gantner.com
Important Safety Information
−The installation, commissioning, and servicing of our products must be performed only by suitably trained
personnel. In particular, electrical connections must only be made by correspondingly qualified specialists.
Always observe the relevant installation regulations in accordance with the national Electrical Engineers
Association.
➔Unqualified personnel may potentially perform actions that result in injury due to electrical shock.
−Where not otherwise stated, installation and maintenance work on our products must be carried out when
disconnected from the power supply. This applies in particular to appliances that are normally supplied by
low-voltage current.
➔If the appliance is not disconnected from power, touching terminals or other internal parts of the
appliance may lead to injury due to electrical shock.
−It is prohibited to alter the products (devices, cabling, etc.).
➔Alterations to the products may subsequently result in personal injury, property damage, or damage to
the products.
−Do not remove protective shields and covers.
➔Removing protective shields and covers may result in personal injury or property damage.
−Do not attempt to repair a product after a defect, failure, or damage is detected. In addition, do not put the
product back into operation. In such cases, it is essential to contact your GANTNER representative or the
GANTNER support hotline.
−The installation, commissioning, operation, and maintenance of the product must be carried out in
accordance with the technical conditions of operation as described in the corresponding documentation.
Therefore, it is essential to read the corresponding chapter of this manual and observe the instructions and
information therein.
−If there are still some points that are not entirely clear, please do not take a chance. All queries can be
clarified by your GANTNER representative or by ringing the GANTNER support hotline.
−Directly on receipt of the goods, inspect both the packaging and the product itself for any signs of damage.
Also check that the delivery is complete and includes all accessories, documentation, auxiliary devices,
etc.
−If the packaging or product has been damaged in transport, or should you suspect that it may have a fault,
the product must not be put into service. Contact your GANTNER representative who will endeavor to
resolve the problem as quickly as possible.
−GANTNER Electronic GmbH accepts no responsibility for any injuries or damage caused as a result of
improper use.
Although great care is taken and we are continuously aiming for improvement, we cannot completely exclude the possibility of
errors appearing in our documentation. GANTNER Electronic GmbH therefore accepts no responsibility for the completeness or
the accuracy of this manual. The right is reserved to make alterations at any time without prior notice.
Should you discover any fault with the product or in its accompanying documentation, or you have any suggestions for
improvement, you may confidently inform your GANTNER representative or GANTNER Electronic GmbH directly.
We especially look forward to hearing from you if you want to let us know that everything is functioning perfectly.

GAT NET.Lock 7020 System
www.gantner.com HB_GAT-NETLOCK7020--EN_12 7
The GAT NET.Lock 7020 was developed and fabricated under the quality management standard ISO 9001 and GANTNER
Electronic GmbH is also certified according to standard ISO 14001.
This product is in conformity with the following EC directives, including all applicable amendments:
- 2014/53/EU (Radio Equipment Directive)
The complete text of the CE Declaration of Conformity is available on the following internet link:
https://www.gantner.com/downloads-gat-netlock7020_gz33sib79r
GANTNER is committed to meeting or exceeding the requirements of the RoHS directive (2011/65/EU). The RoHS
directive requires that manufacturers eliminate or minimize the use of lead, mercury, hexavalent chromium,
cadmium, polybrominated biphenyls and polybrominated diphenyl ethers in electrical and electronic equipment sold
in the EU after July 1, 2006.
The WEEE symbol on GANTNER products and their packaging indicates that the corresponding material must not
be disposed of with normal household waste. Instead such marked waste equipment must be disposed of by
handing it over to a designated electronic waste recycling facility. Separating and recycling this waste equipment at
the time of disposal will help to conserve natural resources and ensure that it is recycled in a manner that protects
human health and the environment. Please contact your local authority for further details of your nearest electronic
waste recycling facility.
FCC INFORMATION (U.S.A.)
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC
Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in
a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used
in accordance with the instruction manual, cause harmful interference to radio communications.
Operation of this equipment in residential area is likely to cause harmful interference in which case the user will be required to
correct the interference at his own expense.
FCC Warning Statement
[Any] changes or modifications not expressly approved by GANTNER Electronic GmbH could void the user's authority to operate
the equipment.
Compliance Information Statements:
GAT NET.Lock 7020 P GAT NET.Controller S 7020 F/ISO
GAT NET.Lock 7020 USB P GAT NET.Controller S 7020 F/ISO light
GAT NET.Controller S 7020 BA GAT NET.Controller S 7020 ICLS
FCC ID: NC4-GEA1190143A
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions: (1)
This device must not cause harmful interference, and (2)
this device must accept any interference received,
including interference that may cause undesired operation.
FCC ID: NC4-GEA1190148A
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions: (1)
This device must not cause harmful interference, and (2)
this device must accept any interference received,
including interference that may cause undesired operation.
FCC ID: NC4-GEA1190149A
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions: (1)
This device must not cause harmful interference, and (2)
this device must accept any interference received,
including interference that may cause undesired operation.
FCC ID: NC4-GEA1190147A
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions: (1)
This device must not cause harmful interference, and (2)
this device must accept any interference received,
including interference that may cause undesired operation.

GAT NET.Lock 7020 System
8 HB_GAT-NETLOCK7020--EN_12 www.gantner.com
INDUSTRY CANADA INFORMATION
Device (Appareil)
IC ID
GAT NET.Lock 7020 P
GAT NET.Lock 7020 USB P
11873A-1190149A
GAT NET.Controller S 7020 F/ISO
GAT NET.Controller S 7020 F/ISO light
11873A-1190143A
GAT NET.Controller S 7020 BA
11873A-1190148A
GAT NET.Controller S 7020 ICLS
11873A-1190147A
This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development
Canada’s licence-exempt RSS(s). Operation is subject to the following two conditions:
(1) This device may not cause interference; and
(2) This device must accept any interference, including interference that may cause undesired operation of the device.
L’émetteur/récepteur exempt de licence contenu dans le présent appareil est conforme aux CNR d’Innovation, Sciences et
Développement économique Canada applicables aux appareils radio exempts de licence. L’exploitation est autorisée aux deux
conditions suivantes:
1) l’appareil ne doit pas produire de brouillage;
2) l’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d’en compromettre le
onctionnement.
ICES Statement (Canada)
This Class B digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la class B est conforme à la norme NMB-003 du Canada.
Radio Frequency (RF) Safety Instructions
The user (or any other persons such as technicians, etc.) must maintain a minimum distance of 20 cm away from the antenna of the
GAT NET.Lock 7020. To complete the identification process, the user may hold their data carrier next to the antenna of the GAT
NET.Lock 7020 until identification has been completed.
Consignes de sécurité relatives aux fréquences radio (RF)
L’utilisateur (ou toute autre personne telle que des techniciens, etc.) doit se tenir à une distance minimale de 20 cm de l’antenne du GAT
NET.Lock 7020. Pour compléter le processus d’identification, l’utilisateur peut placersonID à proximitéduantenneduGAT NET.Lock7020
jusqu’à ce que l’identification soit terminée.

GAT NET.Lock 7020 System
Table of Contents
www.gantner.com HB_GAT-NETLOCK7020--EN_12 9
TABLE OF CONTENTS
1. INTRODUCTION..........................................................................................................................................11
1.1 About this Manual .................................................................................................................................11
1.2 Chapter Overview .................................................................................................................................11
1.3 Contact & Enquiries ..............................................................................................................................11
1.4 Target Group.........................................................................................................................................12
1.5 Formatting.............................................................................................................................................12
1.5.1 Safety-Critical Information .............................................................................................................12
1.5.2 Non-Safety-Critical Information......................................................................................................12
1.5.3 Instructions and Results.................................................................................................................12
2. GENERAL INFORMATION .........................................................................................................................13
2.1 Intended Use.........................................................................................................................................13
2.2 Unintended Use ....................................................................................................................................13
2.3 Functional Description...........................................................................................................................13
2.4 Terminology ..........................................................................................................................................15
2.5 RFID Technology ..................................................................................................................................16
2.6 System Components.............................................................................................................................17
2.7 Order Information Guide .......................................................................................................................20
3. INSTALLATION...........................................................................................................................................21
3.1 Target Group.........................................................................................................................................21
3.2 Test Installation.....................................................................................................................................21
3.3 Metallic and Non-Metallic Doors ...........................................................................................................22
3.4 Bolt Gauge ............................................................................................................................................22
3.5 Replacement After Break-In..................................................................................................................22
3.6 Door Status Function ............................................................................................................................23
3.7 Definition of the Door Hinge (Right or Left Door)..................................................................................23
3.8 Installation Requirements for the GAT NET.Lock 7020 and Bolt Set...................................................24
3.9 Measurement Diagrams for Installation ................................................................................................25
3.9.1 Door Width.....................................................................................................................................25
3.9.2 Dimensions of the GAT NET.Lock 7020 / GAT NET.Lock 7020 P................................................25
3.9.3 Dimensions of the GAT NET.Lock 7020 USB and GAT NET.Lock 7020 USB P..........................26
3.9.4 Dimensions of the GAT NET.Lock BoltSet 7120 (Non-Metallic Doors).........................................26
3.9.5 Dimensions of the GAT NET.Lock BoltSet 7220 (Metallic Doors).................................................27
3.9.6 Dimensions of the GAT NET.Lock BoltSet 7320 (Glass Doors)....................................................27
3.10 Installation in Lockers with Non-Metallic Doors.................................................................................28
3.10.1 Installation Instructions for the GAT NET.Lock 7020 and Non-Metallic Doors..............................29
3.11 Installation in Lockers with Metallic Doors.........................................................................................30
3.11.1 Cutouts in the Metallic Locker Door...............................................................................................31
3.11.2 Installation Instructions for the GAT NET.Lock 7020 and Metallic Doors......................................32
3.12 Installation in Lockers with Glass Doors............................................................................................33
3.12.1 Installation Instructions for the GAT NET.Lock 7020 and Glass Doors.........................................34
3.13 Installation of the GAT NET.Controller M/S 7020 .............................................................................35
3.13.1 Instructions for Mounting the GAT NET.Controller M 7020 and S 7020 .......................................35
4. ELECTRICAL CONNECTIONS...................................................................................................................37
4.1 Target Group.........................................................................................................................................37
4.2 System Structure...................................................................................................................................37
4.3 GAT NET.Lock 7020.............................................................................................................................38
4.3.1 Power Supply.................................................................................................................................38
4.3.2 Connection Cable ..........................................................................................................................38

GAT NET.Lock 7020 System
Table of Contents
10 HB_GAT-NETLOCK7020--EN_12 www.gantner.com
4.3.3 Connection Cable Installation ....................................................................................................... 38
4.4 GAT NET.Controller S 7020................................................................................................................. 40
4.4.1 GAT NET.Lock 7020 Connection.................................................................................................. 40
4.4.2 Sub Controller Connection............................................................................................................ 41
4.4.3 Sub Controller to Master Controller Connection........................................................................... 43
4.4.4 Power Supply Connection............................................................................................................. 43
4.5 GAT NET.Controller M 7020................................................................................................................ 46
4.5.1 Ethernet Connection ..................................................................................................................... 46
4.5.2 Power Supply Connection............................................................................................................. 46
4.5.3 Relay Connection.......................................................................................................................... 47
5. CONFIGURATION AND OPERATION....................................................................................................... 49
5.1 GAT NET.Lock 7020 Antenna Calibration ........................................................................................... 49
5.2 Restarting a Controller ......................................................................................................................... 49
5.3 Resetting a Controller to the Default Settings...................................................................................... 50
5.4 Controller LED Signaling and Buttons.................................................................................................. 51
5.4.1 Sub Controller ............................................................................................................................... 51
5.4.2 Master Controller........................................................................................................................... 52
5.5 GAT NET.Lock 7020 Signalization Overview....................................................................................... 53
5.5.1 General (applicable for all modes)................................................................................................ 53
5.5.2 Personal Locker Mode.................................................................................................................. 53
5.5.3 Dynamic Personal Locker Mode................................................................................................... 53
5.5.4 GAT Lock 5000 Mode................................................................................................................... 54
5.6 Locker Operation for Visitors................................................................................................................ 54
5.6.1 Lock a Locker................................................................................................................................ 54
5.6.2 Unlock and Open a Locker ........................................................................................................... 54
5.6.3 USB Ports ..................................................................................................................................... 54
5.6.4 LED Lighting.................................................................................................................................. 55
5.7 GAT Relaxx Locker Management Software......................................................................................... 55
5.7.1 General.......................................................................................................................................... 55
5.7.2 Installation and Initial Start-Up...................................................................................................... 55
6. CLEANING AND MAINTENANCE ............................................................................................................. 57
6.1 Target Group........................................................................................................................................ 57
6.2 Cleaning ............................................................................................................................................... 57
6.3 Maintenance......................................................................................................................................... 57
6.4 Functional Testing................................................................................................................................ 57
6.5 Disposal................................................................................................................................................ 58
7. TECHNICAL DATA..................................................................................................................................... 59
7.1 GAT NET.Lock 7020 ............................................................................................................................ 59
7.2 GAT NET.Controller S 7020 (Light) ..................................................................................................... 60
7.3 GAT NET.Controller M 7020 (Light)..................................................................................................... 61