ABI INTERIORS 15756 User manual

S ENS O R GOO S E NE CK HO B SP O U T
Dis cla imer: P ro d u c ts in th is ma n u a l mu s t by la w b e in s talled b y licen s ed an d reg is tered tra d es p eo p le in a cco rd a n ce w ith th e releva n t stan d a rds . A B I a n d th e ma n u fa ctu rer/d is trib u to r
res erve t h e rig h t to va ry s p ecif ic a tio n s o r d elete mo d els fro m t h eir ra n g e w ith o u t prio r n o tif ic a t io n . Dimen s io n s a re n o min a l mea s u remen ts o n ly. Th e in f o rma tio n lis t ed is co rrect at th e time
o f p u b lica tio n , h o w ever A B I a n d th e man u f a c tu rer/d is trib u to r ta kes n o res p o n s ib ility fo r p rin tin g erro rs. C o p yrig h t © A B I I n terio rs 2 02 2 Pty Ltd
SPECIFICATIONS
RECOMMENDED USE Domestic/Commercial
MATERIAL 304 Stainless Steel
TEMPERATURE RATING Maximum continuous working temperature 75°C
If the water temperature exceeds 75°C,an approved tempering
valve must be fitted
PRESSURE RATING Recommended minimum working pressure 150kPa
Recommended maximum working pressure 500kPa
Hot and cold water inlet pressure should be equal
SUITABLE HOT WATER UNITS Storage tank: Yes
Continuous Flow: Yes
Gravity Feed: Not suitable
STANDARDS WELS 5.5 Star, 6L/min, T41 855
AS/NZS 3718:2005
WM-022852

Regularly clean with mild
liquid detergent or soap
and water
DO NOT use cream
cleaners or bleach.
These substances are
abrasive
DO NOT use cleaning
pads with abrasive
surfaces as this may
scratch the material
INSTALLATION GUIDE
Note: This product must be installed by a licensed plumber. This is a general installation guide - there are many factors involved that
can alter the installation method. AU/NZ: For installations within Australia and New Zealand, this product must be installed in
compliance with AS/NZS 3500. UK: For installations in the United Kingdom this product must be installed in compliance with the
Water Supply (Water Fittings) Regulations and Water Supply (Water Fittings) (Scotland) Byelaws. Other: For installations outside
these countries, this product must be installed in compliance with the standards in your respective country.
1
INTERIORS
Remove locking collar and washers. Feed flexi hose and sensor
cable through countertop cutout one at a time.
*Note: ensure rubber is correctly recessed into baseplate.
2Replace rubber washer first, followed by the locking collar. Firmly
tighten with a spanner.
3Screw solenoid and battery case bracket to
surrounding wall, ensuring flexy hose can reach
solenoid.
4On the solenoid outlet marked "OUT" connect
the spout flexi hose with thread adapter.
Connect sensor line to the solenoid.
5Connect one side of G1/2 flexi hose to the second
solenoid outlet. Connect the other side to cold
water outlet.
*Note a cistern stop is recommended between flexy
and cold water outlet for flow control.
6Install battery case in bracket and connect to solenoid.
Connect sensor cord to solenoid.
Test and commission for leaks

Regularly clean with mild
liquid detergent or soap
and water
DO NOT use cream
cleaners or bleach.
These substances are
abrasive
DO NOT use cleaning
pads with abrasive
surfaces as this may
scratch the material
INSTALLATION GUIDE
Note: This product must be installed by a licensed plumber. This is a general installation guide - there are many factors involved that
can alter the installation method. AU/NZ: For installations within Australia and New Zealand, this product must be installed in
compliance with AS/NZS 3500. UK: For installations in the United Kingdom this product must be installed in compliance with the
Water Supply (Water Fittings) Regulations and Water Supply (Water Fittings) (Scotland) Byelaws. Other: For installations outside
these countries, this product must be installed in compliance with the standards in your respective country.
1
INTERIORS
2
Connect the power chord from the solenoid to the AC adapter.
AC adapter installation
Connect the battery pack to the AC adapter. (If there is a loss of
power from the wall outlet the adapter will automatically switch to
battery power).
3Connect the AC adapter to the wall outlet and power on.
Test and commission.
1.
2.
SOLENOID
BATTERY PACK

Regularly clean with mild
liquid detergent or soap
and water
DO NOT use cream
cleaners or bleach.
These substances are
abrasive
DO NOT use cleaning
pads with abrasive
surfaces as this may
scratch the material
INTERIORS
Disconnect water supply from solenoid.
Then place your hand under the spout tip to
confirm the current distance. Solenoid will
make an audible click noise to notify you of
sensor activation.
1
2
3
Place a magnet* in front of the sensor window
until the sensor starts flashing.
*A fridge magnet may be convenient.
While the sensor is flashing, place your hand under
the spout at the preferred distance of activation and
wait until the flashing stops. If there is nothing in
front of the sensor while it is flashing, then the sensor
will keep the original distance.
Adjusting the distance of sensor activation
INSTALLATION GUIDE
Note: This product must be installed by a licensed plumber. This is a general installation guide - there are many factors involved that
can alter the installation method. AU/NZ: For installations within Australia and New Zealand, this product must be installed in
compliance with AS/NZS 3500. UK: For installations in the United Kingdom this product must be installed in compliance with the
Water Supply (Water Fittings) Regulations and Water Supply (Water Fittings) (Scotland) Byelaws. Other: For installations outside
these countries, this product must be installed in compliance with the standards in your respective country.

Regularly clean with mild
liquid detergent or soap
and water
DO NOT use cream
cleaners or bleach.
These substances are
abrasive
DO NOT use cleaning
pads with abrasive
surfaces as this may
scratch the material
INSTALLATION GUIDE
Note: This product must be installed by a licensed plumber. This is a general installation guide - there are many factors involved that
can alter the installation method. AU/NZ: For installations within Australia and New Zealand, this product must be installed in
compliance with AS/NZS 3500. UK: For installations in the United Kingdom this product must be installed in compliance with the
Water Supply (Water Fittings) Regulations and Water Supply (Water Fittings) (Scotland) Byelaws. Other: For installations outside
these countries, this product must be installed in compliance with the standards in your respective country. INTERIORS
What's in the box
1 x Allen key
4 x Wall plug
4 x M4 screw
1 x Battery case
1 x Battery bracket
1 x Solenoid
1 x G1/2 flexi - 500mm
1 x Sensor hob spout
1 x AC adapter