Abit SI-2PS User manual

SI-2Ps
Dual Xeon Server Board
Socket 604
User’s Manual
4200-0395-01
Rev. 1.00

Copyright and Warranty Notice
The information in this document is subject to change without notice and does not
represent a commitment on part of the vendor, who assumes no liability or
responsibility for any errors that may appear in this manual.
No warranty or representation, either expressed or implied, is made with respect to the
quality, accuracy or fitness for any particular part of this document. In no event shall
the manufacturer be liable for direct, indirect, special, incidental or consequential
damages arising from any defect or error in this manual or product.
Product names appearing in this manual are for identification purpose only and
trademarks and product names or brand names appearing in this document are
property of their respective owners.
This document contains materials protected under International Copyright Laws. All
rights reserved. No part of this manual may be reproduced, transmitted or transcribed
without the expressed written permission of the manufacturer and authors of this
manual.
SI-2Ps

Table Of Contents
Chapter 1. Introduction .................................................... 1-1
1.1. Specifications ......................................................................... 1-1
1.2. Layout..................................................................................... 1-3
1.3. Jumpers & Connectors Description........................................ 1-4
Chapter 2. Hardware Setup.............................................. 2-1
2.1. CPU Socket ............................................................................ 2-1
2.2. System Memory....................................................................... 2-2
2.3. EPS12V Power Connectors.................................................... 2-3
2.4. FAN Power Connectors.......................................................... 2-4
2.5. CMOS Memory Clearing Header ..........................................2-5
2.6. Front Panel Switches & Indicators Connection Headers ....... 2-6
2.7. IDE Disk Drive Connector..................................................... 2-7
2.8. PCI Expansion Slot ................................................................ 2-8
2.9. Additional COM2 Port Connection Header........................... 2-9
2.10. Additional USB Port Connection Header ............................ 2-10
2.11. External Keyboard/Mouse Connection Header ................... 2-11
2.12. System Management Bus Connection Header..................... 2-12
2.13. VGA Output Connection Header ......................................... 2-13
2.14. Compact Flash Memory Card Reader Slot .......................... 2-14
2.15. Status Indicators ................................................................... 2-15
2.16. Parallel Port Header.............................................................. 2-16
2.17. Debug Card Connection Header (Reserved for internal testing)
.............................................................................................. 2-17
2.18. External I/O Panel Connectors.............................................2-18
Chapter 3. BIOS Setup...................................................... 3-1
3.1. Main Menu ............................................................................. 3-2
User’s Manual

3.2. Advanced Menu ..................................................................... 3-5
3.2.1. Advanced BIOS Features ...................................................3-5
3.2.2. Advanced Chipset Features ................................................3-8
3.2.3. Integrated Peripherals .......................................................3-10
3.2.4. Power Management Setup ................................................3-13
3.2.5. PnP/PCI Configurations ...................................................3-15
3.3. Security Menu ...................................................................... 3-17
3.4. PC Health Menu ................................................................... 3-18
3.5. Clk/Misc. Menu.................................................................... 3-20
3.6. Exit Menu ............................................................................. 3-22
Chapter 4. Driver Installation .......................................... 4-1
4.1. Setup Items ............................................................................. 4-2
Appendix A. How to Get Technical Support ..................... A-1
SI-2Ps

Introduction 1-1
Chapter 1. Introduction
1.1. Specifications
Processor
• Supports dual Intel Xeon processor with 512K L2 cache FSB 533/400
MHz up to 3.2GHz and higher
Chipset
• Intel E7501 Chipset Memory Controller Hub (MCH)
• 2x 82870P2 64-bit PCI/PCI-X Controller Hub 2 (P64H2)
• 82801CA I/O Controller Hub 3-S (ICH3-S)
Memory
• Four 184-pin DIMM sockets
• Supports 144-bit wide dual channel DDR 266/200 memory
• Up to 8GB, ECC Registered memory capacity
AGP
• Onboard ATi RAGE XL PCI interface VGA
System BIOS
• Supports Plug-and-Play (PNP)
• Supports Advanced Configuration Power Interface (ACPI)
• Write-Protect Anti-Virus function by AWARD BIOS
• 4MB Flash ROM
LAN
• 3x Intel 82546EB dual ports 64-bit Gigabit Ethernet Controllers
• Front panel LAN Active/Link LED
Networking Security
• Cavium CN-1120
Extension Slot
• 1x PCI-X, 64bit/133MHz (3.3V)
Internal I/O Connectors
• 1x 44-pin IDE connector
• 1x VGA Port
User’s Manual

1-2 Chapter 1
• 1x COM port header (COM2)
• 1x USB 1.1 header (Each header supports two USB 1.1 devices)
• 1x SM Bus header (For SM Bus and I2C)
Front Panel I/O
• 2x USB 1.1 ports
• 1x COM port (COM1)
• 6x RJ-45 w/Transformer and LED single port LAN connector (GbE)
Back Panel I/O
• 1x 50-pin IDE interface Compact Flash Type II socket
Miscellaneous
• EEB 3.0 form factor (12” x 13”)
• Hardware monitoring – Including Fan speeds, Voltages, System
environment temperature
• Chassis intrusion detector header
• 3.3V 64-bit riser card supported (option)
 Specifications and information contained herein are subject to change
without notice.
SI-2Ps

Introduction 1-3
1.2. Layout
User’s Manual

1-4 Chapter 1
1.3. Jumpers & Connectors Description
Jumpers Description Default Setting
CCMOS1 CMOS Memory Clearing Header Pins 1-2 Closed (Normal)
Connectors Description
CF1 Compact Flash Memory Card Reader Slot
COM2 Additional COM2 Port Connection Header
DIMM 1~4 DDR DIMM Slots
EPS12V1 8-Pin EPS12V Power Connector
EPSPWR1 24-Pin EPS12V Power Connector
FAN1~9 Fan Power Connectors
FPIO1 Front Panel Switches & Indicators Connection Headers
FP-USB1 Additional USB Port Connection Header
IDE1 2.5” Hard Disk Drive Connector
KM1 Keyboard/Mouse Connection Header
LPC Debug Card Connection Header (Reserved for internal
testing)
LPT1 Parallel Port Connection Header
PCI1 64bit/133MHz PCI-X Slot
SM-BUS1 System Management Bus Connection Header
VGA1 VGA Output Connection Header
SI-2Ps

Hardware Setup 2-1
Chapter 2. Hardware Setup
2.1. CPU Socket
This server board provides dual 604-pin Zero Insertion Force (ZIF) sockets to install
the Intel Xeon CPU. You may install either one or two CPUs, but to set up system
with only one CPU, it MUST be installed in the primary socket (socket “CPU0” in
this model). To install a second processor, you must verify that the second processor
is identical to the first processor with same voltage and speed. Using non-identical
processors could cause system failure.
User’s Manual

2-2 Chapter 2
2.2. System Memory
This server board provides six 184-pin Double Data Rate (DDR) Dual Inline Memory
Module (DIMM) slots for Registered ECC DIMM modules with memory expansion
size up to 8GB (DDR266/DDR200).
DIMM Registered ECC DIMM Module Total Memory
1 128MB, 256MB, 512MB, 1GB, 2GB 128MB ~ 2GB
2 128MB, 256MB, 512MB, 1GB, 2GB 128MB ~ 2GB
3 128MB, 256MB, 512MB, 1GB, 2GB 128MB ~ 2GB
4 128MB, 256MB, 512MB, 1GB, 2GB 128MB ~ 2GB
Total System Memory 256MB ~ 8GB
ATTENTION: Populate the DDR DIMMs in-order and in-pair (of the same type
and size) by starting from DIMM1+DIMM2 to DIMM3+DIMM4.
SI-2Ps