Advantech ASMB-935 Series Installation and operation manual

ASMB-935 Startup Manual 1
Before you begin installing your card, please make sure
that the following items have been shipped:
• 1 ASMB-935 Startup Manual
• 1 Driver CD
• 2 Serial ATA HDD data cables
• 2 Serial ATA HDD power cables
• 2 CPU power cables (8P)
• 1 I/O port bracket
• 1 Warranty card
If any of these items are missing or damaged, please
contact your distributor or sales representative immediately.
Note 1: Acrobat Reader is required to view any PDF file.
Acrobat Reader can be downloaded at:
https://www.adobe.com/downloads.html
(Acrobat is a trademark of Adobe)
ASMB-935 LGA 3647 Dual Intel Xeon® Processor Scalable
Family Server Board with 24 DDR4, 5 PCIe x16 + 1 PCIe
x8, 10 SATA3, 6 USB3.0, Dual 10GbE, IPMI
Startup Manual
Standard M/B Functions
• CPU: Dual LGA3647-P0 Intel Xeon® processor scalable
family series
• BIOS: AMI 256 Mb SPI BIOS
• Chipset: Intel® C620 PCH
• System Memory: 24* DDR4-1866/2133/2400/2666
registered ECC DIMM, max. capacity 768 GB
Note 2: Due to the inherent limitations of the PC architec-
ture, the system may not fully detect 768 GB
RAM when 768 GB RAM is installed.
• SATA Interface: 10 SATA3 6 Gb/s ports Intel Rapid
Storage (for Windows only) (supporting software RAID 0,
1, 10 & 5 )
• Serial Ports: Two RS-232 (one on rear I/O, and another
one via pin header)
• Keyboard/Mouse Header (KBMS1): Supports the stan-
dard PS/2 keyboard and mouse via PS/2 cable
• Watchdog Timer: 255 sec/min level timer intervals
• USB Port: Supports up to 6 USB 3.0 ports (2 ports from
onboard 20-pin header) and 5 USB 2.0 ports (1*Type-A,
4 ports from onboard 10-pin header)
VGA Interface
• Chipset: ASPEED AST2500/2510
• Display Memory: 64 MB
• Resolution: Supports VGA up to resolution 1920 x 1200
@ 60 Hz refresh rate
Ethernet Interface
• Interface: 10/100/1000 Mbps & 10Gb (only for LAN3 &
LAN4)
• Controller: LAN1/2: Intel I210; LAN3/4: Intel X557
Mechanical and Environment
• Dimensions (L x W): 330 x 304 mm (13” x 12”)
• Power Supply Voltage: +3.3 V, +5 V, ±12 V, +5 Vsb
• Power Consumption (mainboard only, excluding
IO device): Max. load: [email protected], [email protected],
[email protected], [email protected], [email protected],
[email protected], [email protected]
• Operating Temperature: 0 ~ 40° C (depending on CPU)
• Weight: 1.5 kg (weight of board)
Specications Packing List
For more information on this and other Advantech
products, please visit our website at:
http://www.advantech.com
For technical support and service, please visit our
support website at:
http://support.advantech.com
This manual is for the ASMB-935 series Rev. A1
Part No. 2001093500
Printed in China
1st Edition
May 2018

2 ASMB-935 Startup Manual
The board has a number of jumpers that allow you to con-
figure your system to suit your application. The table below
lists the function of each of the jumpers and connectors.
Connectors
Label Function
ATXPWR1 ATX 24 Pin main power connector
ATX12V1 Processor power connector
(for CPU0)
ATX12V2 Processor power connector(for
CPU1)
BH2 For optional battery kit
BIOS_SKT1 BIOS ROM
BMC_CN1, BMC_CN2 IPMI module header
CN1 CPLD code update header
COM2 Serial port RS-232
CPUFAN0, CPUFAN1 CPU FAN connector
DIMMA1, DIMMA2,
DIMMB1, DIMMB2,
DIMMC1, DIMMC2,
DIMMD1, DIMMD2,
DIMME1, DIMME2,
DIMMF1. DIMMF2
DDR4 slot from CPU0
DIMMG1, DIMMG2,
DIMMH1, DIMMH2,
DIMMI1, DIMMI2,
DIMMJ1, DIMMJ2,
DIMMK1, DIMMK2,
DIMML1. DIMML2
DDR4 slot from CPU1
DIMMC1, DIMMF1,
DIMMI1, DIMML1
DDR4 slot supporting AEP
memory
EX_THR1 Connector for external thermistor
GPIO1 GPIO connector
HDAUD1 Audio header
JFP1, JFP2, JFP3 Front panel header
KBMS1 External keyboard and mouse
connector (6 pin)
LAN1_USB3_12 RJ-45 LAN port 1 + USB 3.0 port
1/2 connector
LAN2_USB3_34 RJ-45 LAN port 2 + USB 3.0 port
3/4 connector
LANLED1 LAN LED extension connector
LPC2 TPM connector
M2_2280_1 M.2 2280 (PCIe & SATA signal)
PCIEX16_SLOT1 PCIE x16 slot (CPU1)
PCIEX16_SLOT2 PCIE x16 slot (CPU1)
PCIEX16_SLOT3 PCIE x16 slot (CPU0)
Jumpers and Connectors (Cont.)
PCIEX8_SLOT4 PCIE x8 slot (CPU0)
PCIEX16_SLOT5 PCIE x16 slot (CPU1)
PCIEX16_SLOT6 PCIE x16 slot (CPU0)
PCN1 CPU power code update header
PEHP1 CPU SMBUS header
PMBUS1 PMBUS connector to
communicate with power supply
SATA0~SATA7 Serial ATA0~7
SGPIO1 sSATA SGPIO header
Slot12V1 For PCIe slot 12V input only
SMBUS1 SMBus header
SPI_CN1 Connector for BIOS update tool
SPI_SKT1 EC EEPROM
sSATA0, sSATA1 sSATA port 0~1
SYS_LED1 System LED connector
SYSFAN0~SYSFAN4 System FAN connector
USB2_78, USB2_910 USB 2.0 port 7, 8, 9, 10 (9-pin
header)
USB2_11 USB 2.0 port 11 (Type-A)
USB3_56 USB 3.0 port 5,6 (20-pin header)
VGA1_COM1 VGA and COM connector
VOLT1 Alarm board power connector
VROC1 Intel Virtual RAID (VROC) key
Jumper List
Label Function
JCASE1 Chassis case open alarm header
JCMOS1 CMOS clear
JME1 ME update
JTHR_SEL
Internal (deault pin1-2) or external
(pin2-3) thermistor selection
JWDT1 Watch dog reset
PSON1 AT(1-2) / ATX(2-3)
JCMOS1/JME1: CMOS clear/ME update function
Closed pins Result
1-2 Keep CMOS data/Disable ME update*
2-3 Clear CMOS data/Enable ME update
*: Default
Keep CMOS data/Disable ME update Clear CMOS data/Enable ME update
1 2 3
1 2 3
Jumpers and Connectors

ASMB-935 Startup Manual 3
The CD disc contains a driver installer program that will
lead you through the installation of various device drivers
needed to take full advantage of your motherboard.
Caution! The computer is supplied with a battery-powered
realtime clock circuit. There is a danger of explo-
sion if battery is incorrectly replaced. Replace
only with same or equivalent type recommended
by the manufacturer. Discard used batteries ac-
cording to manufacturer’s instructions.
The device complies with the requirements in Part 15 of
the FCC rules. Operation is subject to the following two
conditions:
1. This device may not cause harmful interference;
2. This device must accept any interference received,
including interference that may cause undesired
operation.
JFP1, JFP2
Pin.3 #PWR_SW
Pin.6 GND
Pin.9 #RST_SW
Pin.12 GND
Pin.8, Pin.11 HWM_SMB_DATA, HWM_SMB_CLK
*Power button pin is located in Pin 3 & 6 of front panel
connector.
3 6 9 12 PWRSW RESET
HDDLED
SNMP
JFP1
&
1(+) 4 7 10(-)
HDDLED
SM_BUS
SPEAKER
JFP2
&
PWRLED & KEYLOCK
1(+) 23(-) 45JFP3
2(+) 5(-) 8 11
Software Installation
Figure 1: Board Layout: Jumper and Connector Locations
COM2
HDAUD1
KBMS1
GPIO1
SMBUS1
BMC_CN1
LANLED1
BIOS_SKT1
SPI_CN1
SATA2
USB2_11
PCIEX16
_Slot1
PCIEX16
_Slot2
PCIEX16
_Slot3
PCIEX8
_Slot4
PCIEX16
_Slot5
PCIEX16
_Slot6 LAN34 LAN2_
USB3_34
VGA1_COM1
BMC_CN2
PSON1
SSATA0
SSATA1
SATA0
SATA1
SATA3
SATA4
SATA5
SATA7
SATA6
VROC1
VOLT1
LPC2
USB2_910
USB2_78 Slot12V1
PEHP1
SGPIO1 JME1 JCMOS1
JWDT1
USB3_56CPUFAN0
JCASE1
SYSFAN3 ATX12V1
JFP1/2/3SYS_LED1
JTHR_SEL1
EX_THR1
SYSFAN1
SYSFAN0
SYSFAN2
LAN1_
USB3_12
CPUFAN1
DIMMI1
DIMMI2
DIMMH1
DIMMH2
DIMMG1
DIMMG2
DIMMJ2
DIMMJ1
DIMMK2
DIMMK1
DIMML2
DIMML1
CPU1
DIMMF1
DIMMF2
DIMME1
DIMME2
DIMMD1
DIMMD2
DIMMA2
DIMMA1
DIMMB2
DIMMB1
DIMMC2
DIMMC1
ATXPWR1
ATX12V2
PMBUS1
SYSFAN4
SPI_SKT1
CPU0
M2_2280_1
Jumpers and Connectors (Cont.)
Board Layout
Declaration of Conformity