ABLE2 SHO-ME 12.5064 User manual

Luminator LED Trio Light Kit
Model 12.5064
General Information:
The Luminator LED Trio Light is equipped with an internal flasher. It comes from the factory in a random flash mode.
Product Specifications:
Optimum Operation Voltage: +13.8 VDC
Operating Current: 1.5 - 3 amps
Recommended Fuse: 5 amp
Flash Pattern Selection:
To change flash patterns, momentarily apply +12v to the Yellow "Sync-Mode" Wire for less than 5 seconds.
To reset to factory default pattern, apply +12v to the Yellow "Sync-Mode" Wire for more than 5 seconds.*
*Do Not ground YELLOW Wire
When changing flash patterns, you may have to re-start before patterns will synchronize.
Synchronization:
Connect all yellow wires together to synchronize. When wired as shown, the Luminator LED Trio Light will be
synchronized.
Group Selection:
The White "Group Selection" Wire will determine which lights flash at the same time when you have 2 or more lights.
For Group 1, connect White "Group Selection" wire with Red Power wire.
For Group 2, DO NOT connect White "Group Selection" wire to anything.
Group 1 & Group 2 will alternate.
*Do Not use White wire if using only one light.*
Wiring Instructions:
When wiring, always connect ground wire first and power wire last.
Flash Patterns
1. Single Flash - 134 FPM
2. Double Flash - 268 FPM
3. Quad Flash - 536 FPM
4. Super Flash - 1070 FPM
5. Single-On - 134 FPM
6. Quad-On - 536 FPM
7. Triple Flash - 401 FPM
8. Hyper Flash - 1873 FPM
9. Steady
10. Random 1-8 (Default)
09-10-08

12-07
Installation Instructions
1a. Luminator LED Trio Light Installation With Bracket (Diagram A)
Drill out the mounting hole, Point A, on each end of the Luminator LED Trio Light to 11/64".
Attach the bracket to desired location using the (2) longer screws.
Then place the Trio Light into the bracket and attach it using the
shorter screws and locknuts. The gasket will not be needed.
1b. Luminator LED Trio Light Installation Without Bracket (Diagram A)
Use Point B. Drill the 2 holes on the mounting surface for the Luminator LED Trio Light using the
Trio Light as a guide. Place the gasket under the Trio Light. Attach the Trio Light using (2)
longer screws provided.
2. Connect wires to switches as shown in "Diagram C".
"A"
End View
"B"
Front View
BLACK to ground RED to +12v power source
RED jumper
Back of switches
RED to Positive in, Light
WHITE to Yellow on light
SHO-ME 11.1002
Switch Assembly
3
2
1
Fuse
Red Wire
8ft. White Wire-Mode
90.4070 Screw
Black Wire-Ground
5 Amp
fuse 3ft. Red Wire 8ft. Red Wire-Positive
Black
Red Wire
Black
Diagram "A"
Diagram "C"
Diagram "B"
SHO-ME
®
SHO-ME
®
SHO-ME
®
Yellow Wire
Yellow Wire
White Wire
White Wire
SHO-ME
®
SHO-ME
®
Red Wire
Black
Red Wire
Black
Yellow Wire
Yellow Wire
White Wire
White Wire
Group 2 Group 1
SHO-ME
Parts Included in Trio Light Kit
Gasket
Part # 90.6743
(4)
Trio Light
Part # 12.5003
(4)
Bracket
Part # 90.4477
(4) Dual Switch
Part # 11.1002
(1)
#90.4590
(8) #90.4140 (8) #90.4021 (8) #90.4070 (2) #90.4410 (2)
®