Access Lighting 20419LEDDLP User manual

CERTIFICATION: cULus DAMP
NO. 20419LEDDLP
IMPORTANT SAFETY INSTRUCTIONS
MESURES DE SECURITE A RESPECTURE
Before assembling your ACCESS LIGHTING fixture, please make sure that
you carefully read through this instruction sheet. Save this instruction sheet
and refer to it when additions to or changes in the fixture
configuration are made.
Lisez attentivement ce manuel d’instructions. Enregistrer cette feuille
d'instructions et de s'y référer lorsque les ajouts ou changements dans
la configuration de montage sont faites.
CONSULT A QUALIFIED ELECTRICIAN TO ENSURE CORRECT BRANCH
CIRCUIT CONDUCTOR.
CONSULTER UN ELECTRICIEN QUALIFIE POUR VOUS ASSURER QUE LES
CONDUCTEURS DE LA DERIVATION SONT ADEQUATS
THIS PRODUCT MUST BE INSTALLED IN ACCORDANCE WITH THE APPLICABLE
INSTALLATION CODE BY A PERSON FAMILIAR WITH THE CONTSTRUCTION
AND OPERATION OF THE PRODUCT AND THE HAZARDS INVOLVED.
CE PRODUIT DOIT ETRE INSTALLE SELON LE CODE D’INSTALLATION PERTINENT,
COLLECTION APPLICATION MODEL NO.
PAR UNE PERSONNE QUI CONNAIT BIEN LE PRODUIT ET SON FONCTIONNEMENT
AINSI QUE LES RISQUES INHERENTS
NOTE: The important safeguards and instructions that appear in this
manual are not meant to cover all possible conditions and situations that
may occur. It must be understood that common sense, caution and care,
are factors that can’t be built into any product. These factors must be
supplied by the person(s) caring for and operating the fixture.
Read all instructions
Do not install this fixture in hazardous locations.
N'installez pas cet appareil dans des emplacements dangereux.
Do not install any fixture assembly closer than 6 inches from any
curtain or similar combustible material.
Laisser une distance d’au moins 6 pouces entre ce luminaire et la toute
surface combustible.
"WARNING Risk of Fire and Electric Shock."
“CAUTION: Risque d’ Incendie et de Choc Electriques.”
WHAT WE PROVIDE
• Crossbar
• Mounting Hardware
• Mounting plate
• 1 x Glass shade
• 1 x A19 E26 LED bulb
WHAT YOU NEED
•Screwdriver
•Wire Cutters
•Wiring Supplies as Specified
by Electrical Code
GENERAL INFORMATION
All electrical connections must be in accordance with all ordinances,
Local and the U.S. National Electrical Codes (NEC). These fixtures are
intended for mounting to a standard 4” metal octagon outlet box.
The box must be directly supported by the building structure and U.L.
Recognized.
STEP BY STEP INSTRUCTIONS
Before starting your installation disconnect the Power by turning off the
Circuit Breaker or by removing the fuse at the fuse box. Just turning the
light off at the light switch is not sufficient to prevent electrical shock.
1
ELEMENTARY
Wall Fixture
20419LEDDLP

CERTIFICATION: cULus DAMP
NO. 20419LEDDLP
1
PREPARE FIXTURE
If there is an existing fixture remove it.
Expose the supply wires from the J-box.
Mount the supplied crossbar to the J- box.
CONNECT THE WIRES
Gently pull the supply wires. Connect the black
supply wire to the black fixture wire. Secure with
the supplied wire nuts. Connect the white supply
wire to the white fixture wire. Secure with the
supplied wire nuts. Attach
the green J-Box wire
around green hexagonal head screw
or connect it to
the green supply grounding wire of the fixture.
Secure all wires with U.L. Certified electrical tape (not
supplied). Tuck all wires carefully into the J-Box.
MOUNT THE WALL PLATE
Insert the nipple into the central hole of the crossbar
and adjust to suitable length. Fasten the hex nut
against the nipple so that the nipple will not rotate
further. Position the wall plate against the wall and
insert the nipple through the central hole of the wall
plate. Secure the wall plate against the wall by
screwing the decorative cap onto the nipple.
2
3
2

CERTIFICATION: cULus DAMP
NO. 20419LEDDLP
INSERT THE BULB
Insert the supplied bulb. M
DO NOT EXCEED THE MAXIMUM WATTAGE AS
STATED ON THE WARNING LABEL AND INSTRUCTION
ATTACH THE GLASS SHADE
Insert the plastic bushings into the glass side holes to avoid
the glass being broken by the metal finials. Pass the metal
finials through the plastic bushings in the glass side holes
and screw them into the threaded holes on the fixture to
secure the glass shade against the wall. Take care when
assembling or disassembling the shade to avoid breakage
RESTORE THE ELECTRICITY AND
CHECK THE OPERATION OF YOUR
NEW ACCESS LIGHTING FIXTURE
3
CAUTION
Please ensure that the fitting is cool and
switched
off before replacing the
bulb.
DO
NOT use bulbs that might exceed
the
maximumwattage,statedoncautionlabel.
4
5
6
Dimmable fixture - see attached list for compatible dimmer switches.
VER 17 10 1
VER: 17.10.1