Above All LED V-LINE Series User manual

Universal Voltage 26W, 38W, 52W permits operation at
120VAC thru 277VAC or 347VAC or 480VAC, 50 or 60 Hz.
Add: 1501 Industrial Way N, Toms River, NJ 08755 Phone: [phone] E-mail: [email protected]
Web: www.AboveAllLighting.com ©2016 ABOVE ALL Lighting, Inc. All rights reserved
1
LED V-LINE FLOOD LIGHT
Instructions Manual
SUITABLE FOR MODEL
WIRE CONNECTION
Make the following Electrical Connection:
a). Connect the voltage supply line to ACL in Black.
b). Connect the voltage supply Neutral to ACN in White.
c). Connect Green ground lead to the supply ground lead.
SAFETY INSTRUCTION
READ CAREFULLY BEFORE INSTALLING FIXTURE.
PLEASE KEEP THIS MANUAL FOR FUTURE USE.
Fixtures must be wired in accordance with the National
Electrical Code and all applicable local codes. Proper
grounding is required for safety.
THIS PRODUCT MUST BE INSTALLED IN
ACCORDANCE WITH THE APPLICATION CODE BY
A PERSON FAMILIAR WITH THE CONSTRUCTION
AND OPERATION OF THE PRODUCT AND THE
HAZARDS INVOLVED.
MAKE CERTAIN POWER IS OFF BEFORE
INSTALLING OR MAINTAINING FIXTURE.
CHECK THAT VOLTAGE IS COMPATIBLE WITH
FIXTURE DRIVER. USE APPROVED CONNECTORS
FOR ALL ELECTRICAL CONNECTIONS.
MAINTENANCE CAUTION
1. Review the wire connection before beginning, and
make sure xture is grounded properly.
2. For lighting controls, follow control instructions
carefully.
3. Turn power off and wait for xture to cool before
performing maintenance.
4. Maintenance must be done by professionals.
Note: If fxture is furnished with photocell receptacle,
please make sure install the photocell or shorting cap
INSTALLATION
ACCESSORY PACK
WIRE NUT X 5
1. Turn off the power.
2. Locate the mounting points based on the Dimension
Drawing. See Figure 1.
3. Install the trunnion to a desired bracket try by (2)
Bolts, (2) Locking Washers and (2) Nuts (all not
supplied) .
4. Adjust the angle of the xture by trunnion.
a. Loosen the (2) center bolts and (2) angle locking
screws on the trunnion.
b. Swivel xture to a desired angle.
c. Tighten (2) center bolts and (2) angle Locking
Screws.
5. Make the necessary wire connections and waterproof.
Connect wires as above wiring diagram.
TRUNNION MOUNT (TR)
All manuals and user guides at all-guides.com

Add: 1501 Industrial Way N, Toms River, NJ 08755 Phone: [phone] E-mail: [email protected]
Web: www.AboveAllLighting.com ©2016 ABOVE ALL Lighting, Inc. All rights reserved
2
LED V-LINE FLOOD LIGHT
Instructions Manual
TRUNNION MOUNT DRILL PATTERN
1. Turn off the power.
2. Connect wires as above wiring diagram.
3. Knuckle into the pole by thread. Secure the xture with
nut on the pole. Make necessary waterproof for thread.
4. Loosen the locking bolt and swivel xture to a desired
angle.
5. Tighten the locking bolt.
KNUCKLE MOUNT (KN)
1. The sliptter ts a 2-3/8’’ O.D. Tenon. Make
necessary wire connections in the sliptter and knot
wires for strain relief.
2. Place the sliptter over a tenon or pole and secure
the xture with (2) Set Screws on the side of the
Sliptter.
3. Remove the Sliptter Cover Plate by removing (2)
screws on it. Then loosen the Locking Bolt and
swivel xture to a desired angle. Via the scale mark in
the sliptter.
4. Tighten the Locking Bolt and replace the Sliptter
Cover Plate with removed (2) screws.
SLIPFITTER MOUNT (SF)
Ref#:11214-10315
Figure. 1
All manuals and user guides at all-guides.com