Abus SHGW10000 User manual

S H G W 1 0 0 0 0
Q U I C K G U I D E
ABUS Security-Center • Linker Kreuthweg 5 86444 Affing •Germany •
abus.com

ABUS Z-Wave Gateway SHGW10000 Quickguide
Installing the Gateway
Supported Smartphone System Version:
iOS: iPhone or iPad
Requires iOS 6.0 or later
Android Smartphone or Tablet
Requires Android 4.0 or later
Step 1: Download the ABUS Z-Wave One APP
Step 2: Add the Gateway
Click on the „Add a gateway“ and follow the
further instructions in the app.
Step 3: Login
Press the Gateway icon to log in to the
Gateway.
Assign a secure administrator access now by
entering an admin account name and
password.
Step 4: Add a Z-Wave Component
To add a Z-Wave device into the Gateway
(Inclusion), follow the steps below:
1. Set the gateway inclusion mode
a. Press "Component"
b. Press „+“
c. Choose between ABUS devices or
other devices
d. Follow the inclusion steps of the
respective device
2. When the gateway detects the Z-
Wave component, a "Di" tone is
output.
3. After you have assigned a name to
the component, the gateway
confirms the successful inclusion with
a success tone.
Note: If the inclusion failed, check whether The Z-
Wave frequency of the device is the same as of the
Gateway (EU). It may be necessary to exclude the
device before attempting to include it again. Select
the "-" symbol in the component view here and
perform the exclusion procedure.

ABUS Z-Wave Gateway SHGW10000 Quickguide
Step 5: Add a new room
1. Press the „Room“ Icon
2. Press „+“
3. Assing a name
After a room has been created, included
devices can be added to it. To do this, either
go to the room overview and press “+” to
add device or assign the room in the device
overview.
If temperature, humidity and/or brightness
sensors have been added to a room, the
respective values are displayed as a preview
in the room overview. If there are several
devices with the same parameter, you can
choose which value shall be displayed in
the preview.
Step 6: Create a new scene
Up to 60 scenes can be created on each
gateway, each scene consists of
IF/THEN/WHEN elements.
"IF"
is the condition under which the scene
is to be triggered, up to 6 conditions per
scene are possible. These can be and/or
based. The "IF" conditions can be set
according to the status of the Z-Wave
devices, Smartvest, room conditions or
gateway status.
"THEN"
are the actions of the scene, up to 6
actions are possible per scene. The "THEN"
actions can be applied to Z-Wave devices,
Smartvest, room actions or gateway status.
"WHEN"
allows the scene to check different
conditions which conditions can be, e.g.
always, every day, every week or during a
certain period of time. When no time
interval is assigned, the condition “always”
will be applied automatically.

ABUS Z-Wave Gateway SHGW10000 Quickguide
FAQ
What should I do if I have forgotten my
password?
During operation, press the reset button on
the back of the device for five seconds. The
gateway then restores the standard admin
access and standard network configuration
(DHCP).
How do I exclude a device from the
component list if it is defective or lost?
If your device can no longer establish a
connection to the gateway, it can be
removed from the gateway by pressing the
following ICON:
Note: If a device does not respond for more
than 24 hours, the symbol appears
Why my device cannot be included?
1. Make sure that your Z-Wave gateway
and the device communicate on the
same frequency.
2. Your device may already be
connected to another Z-Wave
network, so try an exclusion first.
3. The battery of the device is empty.
What is the default admin login?
Standard admin user: admin
Standard admin password: _____ (empty)
Scope of delivery
Gateway
ID / Password Card
Quickguide
Ethernet Cable
Power Supply 5V / 1,5A
(DC-Stecker: 3,5 x 1,35mm)
Product description
1
Z-Wave LED-Indicator
2
Netzwerk LED-Indicator
3
Status LED-Indicator
4
Reset-Button
5
Power Supply (5V DC / 1A)
6
LAN-interface
7
Speaker
Reset – Factory Default
To completely reset your Z-Wave Gateway to factory
settings, connect to the device using the ABUS Z-
Wave One App. Open the configuration and select the
option "Z-Wave Factory Settings" in the admin area.
If this controller is the primary controller for your
network, resetting it will result in the nodes in your
network being orphaned and it will be necessary
after the reset to exclude and re-include all of the
nodes in the network. If this controller is being used
as a secondary controller in the network, use this
procedure to reset this controller only in the event
that the network primary controller is missing or
otherwise inoperable.

ABUS Z-Wave Gateway SHGW10000 Quickguide
Z-Wave configuration
Association group
Group
No.
Max.
Nodes
Description
1
1
Z-Wave Plus Lifeline, report
Device Reset Locally when
reset
Device Detection
Added device will detect automatically,
users can control it (on/off, change color,
lighting, etc.) and watch information
(battery, meter, etc.) via Z-Wave ONE App.
Different brands
Z-Wave enabled device can be included and
excluded normally. Included devices will
show on device list. All non-battery
powered nodes can act as repeaters
regardless of manufacturers.
Basis command
Basic command is useful in a scene.
Replication
Controller can transmit protocol replication
data automatically.
About Security
This controller is a security enabled Z-Wave
Plus product. If necessary, it will use
encrypted Z-Wave Plus messages to
communicate to other security enabled Z-
Wave Plus products.
BASIC SET
For unknown device, press device icon will
show on/off icon, select on/off and press
ok will send BASIC SET 0xff/0x00.
Z-Wave Command Classes
Supported Z-Wave Command Classes:
COMMAND_CLASS_ZWAVEPLUS_INFO _V2
COMMAND_CLASS_VERSION_V2
COMMAND_CLASS_ASSOCIATION_GRP_INFO
COMMAND_CLASS_ASSOCIATION_V2
COMMAND_CLASS_MANUFACTURER_SPECIFIC_V2
COMMAND_CLASS_SECURITY
COMMAND_CLASS_SECURITY_2
COMMAND_CLASS_DEVICE_RESET_LOCALLY
COMMAND_CLASS_APPLICATION_STATUS
COMMAND_CLASS_POWERLEVEL
COMMAND_CLASS_CONTROLLER_REPLICATION
COMMAND_CLASS_BASIC
COMMAND_CLASS_CRC_16_ENCAP
COMMAND_CLASS_TRANSPORT_SERVICE_V2
COMMAND_CLASS_SUPERVISION
Controlled Command Classes:
COMMAND_CLASS_BASIC
COMMAND_CLASS_SECURITY
COMMAND_CLASS_SECURITY_2
COMMAND_CLASS_ASSOCIATION_GRP_INFO
COMMAND_CLASS_ASSOCIATION_V2
COMMAND_CLASS_WAKE_UP_V2
COMMAND_CLASS_MULTI_CHANNEL_V4
COMMAND_CLASS_SWITCH_BINARY
COMMAND_CLASS_SWITCH_MULTILEVEL_V2
COMMAND_CLASS_SENSOR_BINARY_V2
COMMAND_CLASS_SENSOR_MULTILEVEL
COMMAND_CLASS_METER
COMMAND_CLASS_COLOR_CONTROL
COMMAND_CLASS_DOOR_LOCK
COMMAND_CLASS_NOTIFICATION_V4
COMMAND_CLASS_BATTERY
COMMAND_CLASS_SENSOR_ALARM
COMMAND_CLASS_INCLUSION_CONTROLLER
COMMAND_CLASS_CRC_16_ENCAP

Eine alternative Inbetriebnahme sowie detaillierte Informationen erhalten
Sie in der Bedienungsanleitung erhältlich auf der Website:
abus.com/product/SHGW10000
Vous trouverez une alternative de mise en service ainsi que des
informations détaillées dans le manuel d’utilisateur disponible sur le site
Internet : abus.com/product/ SHGW10000
Een alternatieve ingebruikname en gedetailleerde informatie vindt u in de
gebruikershandleiding op de website: abus.com/product/SHGW10000
Per informazioni su una messa in funzione alternativa o sui dettagli del
prodotto, consultare le istruzioni per l‘uso disponibili all‘indirizzo:
abus.com/products/SHGW10000
An alternative installation as well as detailed information can be found in
the user manual which is available on the website:
abus.com/product/SHGW10000
Alternativ idrifttagning samt detaljerede oplysninger findes i
betjeningsvejledningen, som findes på hjemmesiden:
abus.com/product/SHGW10000
Informacje dotyczące alternatywnych sposobów uruchomienia oraz
dodatkowe szczegóły znajdują się w instrukcji obsługi, którą można pobrać
na stronie: abus.com/ product/SHGW10000
En el manual de instrucciones disponible en nuestra página web podrá
consultar una puesta en funcionamiento alternativa, así como información
más detallada. abus.com/product/SHGW10000
Alternativ idrifttagning samt detaljerad information finns i bruksanvisningen
som kan hämtas på webbsidan: abus.com/product/SHGW10000