Abus TVAC20000 User manual

10
TVAC20000
User manual
Version 01/2010
Original English user manual. Keep for future use.

11
English
Introduction
Dear Customer,
Thank you for purchasing this product.
This product meets the requirements of the applicable European and national guidelines. The
corresponding declarations and documents can be obtained from the manufacturer
(www.abus-sc.com).
To maintain this condition and to ensure risk-free operation, you as the user must observe these operation
instructions!
Before initial start-up, read through the complete operating instructions observing operating and safety
instructions.
All company and product names mentioned in this document are registered trademarks.
All rights reserved.
If you have any questions, please contact your installer or your local dealer!
Disclaimer
This user manual was prepared with greatest care. If you should notice omissions or inaccuracies, please
inform us about these on the back of this manual given address.
The ABUS Security-Center GmbH assumes no liability for technical and typographical faults and reserves
the right to make at any time modifications to the product or user manual without a previous announcement.
The company is not liable or responsible for direct and indirect subsequent damages which are caused in
connection with the equipment, the performance and the use of this product.
No guarantee for the content of this document is taken.

12
English
Icon explanation
A flash in the triangle is used if there is danger for the health, e.g. by an electric shock.
An exclamation mark in the triangle points to an important note in this user manual
which must be minded.
This symbol can be found when you are to be given tips and information on operation.
Important safety advice
The warranty will expire for damage due to non-compliance with these operating
instructions. ABUS will not be liable for any consequential loss!
ABUS will not accept liability for damage to property or personal injury caused by
incorrect handling or non-compliance with the safety-instructions.
In such cases the warranty will expire.
The device has been manufactured in compliance with international safety standards. Please read these
safety advices carefully.
Safety advice
1. Mains supply
90 - 250V AC 50/60Hz
Operate this product only from the type of power supply indicated on the marking label. If you are not sure
of the type of power supplied to your home, consult your local power company. Disconnect the product
from the mains before you start any maintenance or installation procedures.
2. Overloading
Do not overload a wall outlet, extension cord or adapter as this may result in electric fire or shock.
3. Liquids
Setup the device only in dry and dust-protected rooms. Protect the device from any kind of liquids
entering.
4. Cleaning
Disconnect the product from the wall outlet before cleaning. Use a light damp cloth (no solvents) to dust
the product.
5. Ventilation
The slots on top of the product must be left uncovered to allow proper airflow into the unit. Do not stand
the product on soft furnishings or carpets. Do not stack electronic equipments on top of the product.
6. Accessories
Do not use any unsupported accessories as these may be hazardous or cause damage the product.
7. Location
xSetup the device only in dry and dust-protected rooms.
xProtect the device from any kind of liquids entering.
xDo not place the device near a radiator or heat register.
xSetup the device only in areas with the advised operating temperatures of 0° ~ 50°C.

13
English
Warnings
Follow all safety and operating advises before starting-up the device!
1. Follow these directions in order to avoid damage of the power cord or plug:
xDo not modify or process the power cord or plug arbitrarily.
xDo not bend or twist the power cord.
xMake sure to disconnect the power cord holding the plug.
xKeep heating appliances as far as possible from the power cord in order to prevent the cover
vinyl from melting.
2. Follow these directions. Failure to follow any of them may cause electrical shock:
Do not open the main body or the power supply.
xDo not insert metal or inflammable objects inside the product.
xIn order to avoid any damage during lighting use a surge protection.
3. Do not use the product when it is out of order. If you continue to use the product when defective, serious
damage can be caused to it. Make sure to contact your local product distributor if the product is out of
order.
During the installation into an existing video surveillance system make sure that all devices are
disconnected from the low and supply voltage circuit.
If in doubt allow a professional electrician to mount, install and wire-up your device. Improper
electrical connection to the mains does not only represent at threat to you but also to other
persons.
W
ire-up the entire system making sure that the mains and low voltage circuit remain separated
and cannot come into contact with each other in normal use or due to any malfunctioning.
Unpacking
While you are unpacking the device please handle it with utmost care.
If you notice any damage of the original packaging, please check at first the device.
If the device shows damages, please contact your local dealer.

14
English
Table of contents

1. Intended use .........................................................................................................................................15
2. Scope of delivery..................................................................................................................................15
3. Features and functions........................................................................................................................15
4. Physical descriptions ..........................................................................................................................16
5. Maintenance and cleaning...................................................................................................................17
5.1 Maintenance.................................................................................................................................17
5.2 Cleaning.......................................................................................................................................17
6. Disposal.................................................................................................................................................17
7. Technical data.......................................................................................................................................18

15
English
1. Intended use
This converter attends to convert a Composite- and S-Video signal into a VGA signal. You have the possibility
to use a recorder or camera (B/W and color cameras) with a composite output together with a monitor that
has a VGA input.
You also have an additional VGA input to convert this signal into a higher resolution or to switch between the
analogue video input and a VGA signal (e.g. of a PC).
A detailed description of all functions can be found in chapter „3 Features and functions“.
2. Scope of delivery
3. Features and functions
xConverts BNC or S-Video signal into a VGA signal
xMax. resolution 1280 x 1024 pixel (SXGA)
xImage freeze function
xManual switching between input signals
xPlug & Play
BNC-VGA converter Power supply VGA cable S-Video cable

16
English
4. Physical descriptions
Description of the connectors:
Description of the function keys:
cVGA Output Output of the converted signal into VGA
dVGA input Recorder or PC signal input
eS-Video input Y/C Video signal input
fBNC input Composite video signal input (BNC, female, FBAS, 1 Vpp)
gPower supply 5VDC / 1A
Input Selection of the input signal. At the left top the actual input is
shown.
You can choose between following inputs:
S-Video, VGA and CVBS (BNC)
Menu By pressing this button you enter the menu. If you press the button
several times you can switch between the menu items.
You can do adjust following settings:
Bright= Brightness
Contrast
Color
Hue
For all menu points you can adjust the value in a range between 0
and 99.
Freeze / + During the normal mode you can freeze the picture by pressing
this button. If you press the button again you can switch to live
view.
In the menu you can increase the value by pressing this button. If
you press it for longer time you can increase the value faster.
Spannungs-
versorgung
V
GA Input for
PC / Recorder
S-
V
ideo Input
of recorder or
camera
V
GA output
of monitor
Funktionstasten
d e f
g
Power
supply
BNC input of
camera or
recorder
Function keys
c

17
English
5. Maintenance and cleaning
5.1 Maintenance
Regularly check the product's physical state, e.g. check for damage of the housing.
If you suspect that safe operation cannot be guaranteed anymore, disconnect the product and ensure that it
cannot be used by mistake.
You can assume that safe operation is not possible anymore when
xthe device shows visible damage,
xthe device does not function anymore
Please note:
The product is maintenance free for you. Inside the product are no parts that can be checked or
repaired, so do not ever open it.
5.2 Cleaning
Wipe the product with a clean, dry cloth. If the device is very dirty, you can moisten the cloth with lukewarm
water.
Ensure that no liquids can get into the device.
Do not use any chemical cleaners, since they could damage the housing surface or the screen
(discolorations).
6. Disposal
Devices with this marking should not be put in the household garbage. Dispose of the
product at the end of its lifetime according to the applicable regulations.
Resolution / - By pressing this button you can choose the resolution. By pressing
this button several times you can switch between the different
resolutions.
You can choose between following resolutions:
800x600 Pixel @ 60Hz
800x600 Pixel @ 75 Hz
1024x768 Pixel @ 60 Hz
1280x1024 Pixel @ 60 Hz
Many monitors have an automatic adjusting function therefore it
can take some seconds that the picture calibrates.
In the menu you can decrease the value by pressing this button. If
you press it for longer time you can decrease the value faster.

18
English
7. Technical data
Typenumber TVAC20000
Inputs 1x BNC (FBAS, 1 Vpp), 1x S-Video, 1x VGA
Outputs 1x VGA
Resolution 800x600 Pixel @ 60Hz
800x600 Pixel @ 75 Hz
1024x768 Pixel @ 60 Hz
1280x1024 Pixel @ 60 Hz
Video system PAL / NTSC
Impedance 75 
Power supply 5VDC / 1A
Dimensions (WxHxD) 105 x 65 x 24 mm

19