Accurist 7024474 Manual

Instruction Guide
and
2 year Guarantee
IA05A

Service and Repairs
Your ACCURIST watch is guaranteed against defects in materials and
workmanship for a period of 2 years from the date of purchase. During
this period, we will exchange or repair, at our discretion, any defective
components free of charge.
IMPORTANT - Not covered by Guarantee
1. Batteries, straps and bracelets.
2. Damage caused by accident, misuse or lack of care.
3. Water penetrations except in watches marked as “Water Resistant”.
SERVICING AND REPAIRS UNDER GUARANTEE
Please post your watch, together with the Retailer’s Sales Receipt
or proof of purchase, the completed Guarantee slip, and a brief note
to explain the nature of the fault, by Registered Post or Recorded
Delivery to the address shown. Do not send the presentation box as
this will NOT be returned.
SERVICING AND REPAIRS OUTSIDE OF GUARANTEE
Available at a reasonable charge after an estimate has been sent by
T.P. (UK) Ltd. Send your watch to us by Registered Post or Recorded
Delivery to the address shown.
Important Note
It is important to identify your watch correctly. If, after reading
this Instruction Guide, you have any further questions regarding
the use, operation or adjustment of your watch, please call us
during ofce hours on 0116 288 2500.
T.P. (UK) Ltd, Alexander House, Chartwell Drive, Wigston, Leicester
LE18 2EZ
United Kingdom.

Water Resistance
If your watch is water resistant, it will clearly state “Water Resistant” or
have a static water pressure indication (e.g. “30/50/100/200 metres”)
on the dial and/or case back.
If it is not marked as water resistant, it should not be allowed to come
into contact with water or be worn in conditions that could expose
it to moisture (e.g. washing, heavy rain etc.). Certain chemicals in
water may damage the watch seals. To maintain water resistance, we
recommend that your watch is serviced and re-sealed at least every
12 months by T.P. (UK) Ltd.
IMPORTANT
Buttons must not be operated while in contact with water.
WATER RESISTANT or RESISTANT TO 30 METRES
Suitable for normal everyday use and will resist exposure to splashes
and rain; it is NOT designed to be used whilst bathing or swimming.
WATER RESISTANT TO 50 METRES
As 30 metres plus bathing or swimming.
WATER RESISTANT TO 100 METRES
As 50 metres plus pool side diving and snorkelling, but not high board
or scuba diving.
WATER RESISTANT TO 200 METRES
As 100 metres plus scuba diving, but not high board diving.

Digital Instructions
Time/Date Settings
System Settings
A
B
D
C
A
B
D
C
A
B
D
C
A
B
D
C

Digital Instructions
Using the backlight feature
1. Press ‘A’ button to activate the backlight for 3 seconds.
System settings:
Using the night feature
1. Hold down ‘C’ button and press ‘B’ button to enter the system
settings mode.
2. Press ‘D’ button to select “NGT” on/off.
• When “NGT” is on, the backlight will activate when any button is
pressed.
Setting the time schedule
• Before setting the time, please check that the correct time schedule
is selected.
• To select the time time schedule, press the buttons in the following
sequence.
1. Hold down ‘C’ button and press ‘B’ to enter system settings mode.
2. Press ‘C’ to cycle through the time zones and press ‘D’ to select
either “STD” standard time or “DST” daylight saving time.
3. Press the ‘B’ button to conrm selection and return to real time
mode.

Digital Instructions
Setting the time
1. When in real time mode, hold down ‘B’ button to enter time
setting mode.
2. When the whole display is ashing, press the ‘D’ button to se-
lect the chime hourly function on/off, then press the ‘C’ button.
3. When the time zone display is ashing, press the ‘D’ button to
cycle through the time zones, then press the ‘C’ button.
4. When the seconds display is ashing, press the ‘D’ button to
reset to zero, then press the ‘C’ button.
5. When the minute display is ashing, press the ‘D’ button to
increase the value or hold the ‘D’ button to increase quickly,
then press the ‘C’ button.
6. When the hour display is ashing, repeat step 5. Pressing the
‘C’ button at this stage will enter the date setting display.
Setting the date
• Continuing on from setting the time, press the buttons in the
following sequence to set the date.
1. When the month display is ashing, press the ‘D’ button to
cycle through the values, then press the ‘C’ button.
2. When the day display is ashing, press the ‘D’ button to cycle
through the values, then press the ‘C’ button.
3. Repeat step 2 to select the year. Pressing the ‘C’ button at this
stage will enter the 24 hour setting display.
Selecting 12/24h format
• Continuing on from setting the date, when the display is ashing,
press the ‘D’ button to select either 12h or 24h format. To conrm
the time, date and 24h settings, press the ‘B’ button to return to
real time mode.
* Instructions continued overleaf

GUARANTEE
PLEASE USE BLOCK CAPITALS
NAME
ADDRESS
POST CODE
DAYTIME TELEPHONE NUMBER
IMPORTANT
This guarantee slip should be retained by the owner of
the product and should be sent to Timeproducts (UK) Ltd.
together with the product and £12 to cover the handling
and postage when service under Guarantee is required.

GUARANTEE
DATE OF PURCHASE:
Retailers stamp if required or full name and address:
Please attach the receipt or proof of purchase; failure to attach
these may invalidate this Guarantee.
This Guarantee does not affect your statutory rights.
IA05A/07-2017

Digital Instructions
Stopwatch Mode
Alarm Settings Mode
A
B
D
C
A
B
D
C
A
B
D
C
A
B
D
C

Digital Instructions
Setting the alarm feature
• To set the alarm, press the ‘B’ button repeatedly until the
alarm display is shown, then press the buttons in the following
sequence. Note: the watches covered in this manual have 3
individual alarms labelled AL 1, AL 2 and AL 3.
1. Press the ‘C’ button to cycle through and select the time zone.
2. Hold down ‘B’ button for 2 seconds to enter the alarm
settings mode.
3. Press the ‘D’ button to select alarm on/off, then press the
‘C’ button.
4. Press or hold down the ‘D’ button to set the hour value, then
press the ‘C’ button.
5. Repeat step 4 to set the minute value, then press the ‘B’
button to conrm the alarm settings.
• Each alarm can be set for different times in different time zones
independently.
Using the stopwatch feature
• To use the stopwatch feature, press the ‘B’ button repeatedly until
the stopwatch “CHR” display is shown, then press the buttons in
the following sequence. Note: the stopwatch measurement can
time up to 10 hours.
• Standard and accumulated elapsed time measurement
1. Press the ‘D’ button to start the counter, then press the ‘D’
button again to pause/stop.
2. To continue timing, press the ‘D’ button, then press the ‘D’
button again to pause/stop. This step can be repeated as
often as required.
3. Press the ‘C’ and ‘D’ buttons together to reset the counter
to zero.

Digital Instructions
Using the stopwatch feature conitnued
• Split time measurement
1. Press the ‘D’ button to start the counter, then press the ‘C’
button to split the timing.
2. Press the ‘D’ button to pause and resume counting.
* The stopwatch can record up to 10 laps. If the counter is still running
after the maximum 10 laps have been recorded, any additional
elapsed time will be added to the nal lap time.
* Once the counter has been stopped and no further timing is
required, press the ‘C’ button to cycle through and view the recorded
lap times.
* If the mode is changed by pressing the ‘B’ button whilst the counter
is running, timing will continue in the background until the counter
is stopped.
Using the countdown feature
• To use the countdown feature, press the ‘B’ button repeatedly
until the countdown “TMR” display is shown, then press the
buttons in the following sequence.
1. Press the ‘C’ button to enter the countdown settings mode.
2. When the display is ashing, press or hold the ‘D’ button to
increase the countdown duration. Press the ‘C’ button to turn
on/off the repeat countdown function.
3. Press the ‘B’ button to conrm and set the coundown duration,
then press the ‘D’ button to start and stop the timer.
* The maximum countdown duration is 180 minutes. The repeat count-
down function will automatically restart the same countdown once the
timer reaches zero.
* The countdown duration will automatically set if no button is pressed
after 1 minute.

Digital Instructions
Using the countdown feature continued
4. To reset the countdown, the timer must rst be stopped,
then press the ‘C’ button to enter the countdown settings
mode and then the ‘B’ button to reset the timer to the chosen
countdown duration.
* During the countdown a tone will sound for every 10 seconds
elapsed. During the nal 10 seconds of the countdown a tone will
sound for every second elapsed. Once the countdown is complete, an
alarm tone will sound until any button is pressed.
Countdown Timer Settings Mode
A
B
D
C
A
B
D
C

Analogue Instructions
Setting the time
1. Pull the crown out to position ‘2’.
2. Turn the crown until the hands show the correct time.
3. Return the crown to position ‘1’.
1 2

World Time Zone Reference Table
City Code City Country
Coordinated Universal Time
London
Paris
UTC
LON
PAR
ROM
CAI
MOW
DXB
KHI
DEL
DAC
BKK
SIN
HKG
TYO
SYD
NOU
AKL
HNL
ANC
LAX
DEN
CHI
NYC
CCS
RIO
Rome
Cairo
Moscow
Dubai
Karachi
New Delhi
Dhaka
Bangkok
Singapore
Hong Kong
Tokyo
Sydney
Noumea
Auckland
Honolulu
Anchorage
Los Angeles
Denver
Chicago
New York
Caracas
Rio de Janeiro
New Caledonia
New Zealand
USA
USA
USA
USA
USA
USA
Venezuela
Brazil
UK
N/A N/A
=00:00 UTC
+01:00 UTC
+01:00 UTC
+02:00 UTC
+03:00 UTC
+04:00 UTC
+05:00 UTC
+05:30 UTC
+06:00 UTC
+07:00 UTC
+08:00 UTC
+08:00 UTC
+09:00 UTC
+10:00 UTC
+11:00 UTC
+12:00 UTC
-10:00 UTC
-09:00 UTC
-08:00 UTC
-07:00 UTC
-06:00 UTC
-05:00 UTC
-04:00 UTC
-03:00 UTC
France
Italy
Egypt
Russia
UAE
Pakistan
India
Bangladesh
Thailand
Singapore
China
Japan
Australia
Time Difference