Accurist IA04 Manual

Instruction Guide
IA04

Service and Repairs
Your ACCURIST watch is guaranteed against defects in materials and
workmanship for a period of 2 years from the date of purchase. During
this period, we will exchange or repair, at our discretion, any defective
components free of charge.
IMPORTANT - Not covered by Guarantee
1. Batteries, straps and bracelets.
2. Damage caused by accident, misuse or lack of care.
3. Water penetrations except in watches marked as “Water Resistant”.
SERVICING AND REPAIRS UNDER GUARANTEE
Please post your watch, together with the Retailer’s Sales Receipt
or proof of purchase, the completed Guarantee slip, and a brief note
to explain the nature of the fault, by Registered Post or Recorded
Delivery to the address shown. Do not send the presentation box as
this will NOT be returned.
SERVICING AND REPAIRS OUTSIDE OF GUARANTEE
Available at a reasonable charge after an estimate has been sent by
T.P. (UK) Ltd. Send your watch to us by Registered Post or Recorded
Delivery to the address shown.
Important Note
It is important to identify your watch correctly. If, after reading this
Instruction Guide, you have any further questions regarding the use,
operation or adjustment of your watch, please call us during ofce
hours on 0116 288 2500.
T.P. (UK) Ltd, Alexander House, Chartwell Drive, Wigston, Leicester
LE18 2EZ
United Kingdom.

Water Resistance
If your watch is water resistant, it will clearly state “Water Resistant” or
have a static water pressure indication (e.g. “30/50/100/200 metres”)
on the dial and/or case back.
If it is not marked as water resistant, it should not be allowed to come
into contact with water or be worn in conditions that could expose
it to moisture (e.g. washing, heavy rain etc.). Certain chemicals in
water may damage the watch seals. To maintain water resistance, we
recommend that your watch is serviced and re-sealed at least every
12 months by T.P. (UK) Ltd.
IMPORTANT
Buttons must not be operated while in contact with water.
WATER RESISTANT or RESISTANT TO 30 METRES
Suitable for normal everyday use and will resist exposure to splashes
and rain; it is NOT designed to be used whilst bathing or swimming.
WATER RESISTANT TO 50 METRES
As 30 metres plus bathing or swimming.
WATER RESISTANT TO 100 METRES
As 50 metres plus pool side diving and snorkelling, but not high board
or scuba diving.
WATER RESISTANT TO 200 METRES
As 100 metres plus scuba diving, but not high board diving.

3 eye chronograph (1/10th sec)
with date
* Chronograph timing up to 60 minutes including 1/10th of
a second.
A
B
1 2 3
SEC
1/10th
MIN

3 eye chronograph (1/10th sec)
with date
Resetting the chronograph function:
• Before setting the time please check that all
chronograph hands are at the “0” / 12 o’clock
position.
• To reset the hands to the “0” / 12 o’clock position
press the buttons on your watch in the following
sequence:
1. If the chronograph is counting then press ‘A’ to stop
the chronograph and then ‘B’ to reset back to “0”.
2. If split timing is displayed then press ‘B’ then ‘A’
followed by ‘B’ again to reset.

3 eye chronograph (1/10th sec)
with date
Setting the time:
* The chronograph measurement must be stopped before
the time can be set.
1. Pull the crown out to position ‘2’.
2. Turn the crown clockwise until the previous date is
displayed.
3. Now pull the crown out to position ‘3’ and adjust the
hands to the desired time.
4. Push crown back to position ‘1’.
* Do not attempt to set the date between 9:00 PM and 1:00
AM as the date change cycle is already in progress.

3 eye chronograph (1/10th sec)
with date
Using the stop watch/chronograph feature:
* The chronograph measurement can time up to 60 minutes.
• Standard measurement:
1. Press ‘A’ to start the chronograph timing, then press
‘A’ to stop the timing.
2. Press ‘B’ to reset the chronograph.
• Accumulated elapsed time measurement:
1. Press ‘A’ to start timing, then press ‘A’ to stop the
timing.
2. Restart the timing by pressing ‘A’ as many times
as required.
3. Press ‘A’ to stop the chronograph and ‘B’ to reset.

3 eye chronograph (1/10th sec)
with date
Using the stop watch/chronograph feature
continued:
• Split time measurement:
1. Press ‘A’ to start the timing, then press ‘B’ to split
the timing.
2. Press ‘B’ to release the timing as many times as
required.
3. Press ‘A’ to stop the chronograph timing.
4. Press ‘B’ to reset the chronograph.