Accurist MB 119 User manual

CASEBACK MARKINGS
Model Number
Calibre Number
Battery Number

CARE OF YOUR WATCH
Avoid temperature extremes
1. Avoid leaving your watch in direct sunlight or in extremely warm
conditions for long periods of time: this will cause malfunctioning and
shorten the life of the battery.
2. Do not leave your watch for long periods of time in extremely cold
places; this may cause your watch to gain or lose time. Should it begin to
gain or lose time, place your watch on your wrist to restore it to its normal
working temperature.
Avoid wet conditions
1. Do not operate the buttons when your watch is wet, even on models
marked ‘Water Resistant’.
2. Check caseback markings and refer to the Resistance to water section.

Care Of Your Watch
Avoid strong shocks
1. This watch will withstand the bumps and jars normally incurred during
sports activities.
2. Avoid dropping your watch on the ground or otherwise imparting severe
shock to it.
Avoid strong magnetic fields
1. Keep your watch away from strong magnets.
2. Generally, your watch is not affected by magnetic fields from household
appliances such as television sets and stereo equipment.

Care Of Your Watch
Avoid harmful chemicals, solvents & gases
1. Avoid wearing your watch in the presence of strong chemicals, solvents
or gases.
2. Avoid materials such as gasoline, benzene, paint thinner, alcohol, spray
cosmetics, nail polish, nail polish remover, adhesives or paint.
Periodic inspection
1. A regular 4 to 5 years service by an authorised Accurist technician will
ensure trouble free operation.
2. Refer to the After Sales Service section for details.

Care Of Your Watch
IMPORTANT
1. Keep the batteries out of reach of infants and small children. Should
accidental ingestion occur consult a doctor immediately.
2. Do not attempt to replace the battery yourself as this invalidates your
guarantee.
Keep your watch clean
Wipe off any moisture that adheres to the case, glass or band with a soft,
clean cloth.

BRACELET ADJUSTMENT
The bracelet requires a small adjustment and the model has
a Z-type clasp.
1. Depress the end of the spring bar
on the centre clasp with a pin.
2. Relocate the spring bar in an
alternative hole.

Bracelet Adjustment
The bracelet requires a significant adjustment or the model does not have
a Z-type clasp.
1. Use the enclosed wrist gauge to measure and mark the size of your wrist.
2. Return the completed wrist gauge with your watch.
3. Follow the instructions in the After Sales Service section to return your
watch for adjustment. Your watch will be adjusted free of charge.

RESISTANCE TO WATER
Indications on dial or caseback Light spray,
Perspiration,
Light rain, etc.
Swimming,
etc.
Dial Caseback
-Water resistant Ok X
Water resistant
50M (5 ATM)
Water resistant Ok Ok
Water resistant
100M (10 ATM)
Water resistant Ok Ok
Water resistant
150M (15 ATM)
and deeper
Water resistant Ok Ok

QUARTZ ANALOGUE OPERATING INSTRUCTIONS
Position A
Position B

Quartz Analogue Operating Instructions
Please note:
The second hand will not start moving until the crown has been returned
to Position A.
To set the time:
1. Gently pull out crown to Position B.
2. Turn crown either way to correct time.
3. Push in crown to Position A.

QUARTZ ANALOGUE WITH DATE OPERATING INSTRUCTIONS
24 hour hand
Second hand
Date
Date position may be located at different position depends on model.
1st position
2nd position
Minute hand
Normal crown position

Quartz Analogue With Date Operating Instructions
Setting the time:
1. Pull the crown out to the 2nd position.
2. Turn the crown to set hour and minute hands.
3. When the crown is pushed back to the normal position, second hand
begins to run.
Setting the time:
1. Pull the crown out to the 1st position.
2. Turn the crown counter-clockwise to set the date.
* If the date is set between the hours of around 9:00 PM and 1:00 AM,
the date may not change the following day.
3. After the date has been set, push the crown back to the normal position.

Quartz Analogue With Date Operating Instructions
For Calendar Models
Positions: A B C

Quartz Analogue With Date Operating Instructions
To set the calendar/date:
1. Gently pull out crown to Position B.
2. Turn crown anti-clockwise to adjust date, clockwise to adjust the day.
3. Push in crown to Position A.
Note: The Day will start to change at 11.25 p.m. and complete its change by
12 0’ clock midnight. The Date will start to change at 12 0’ clock midnight
and complete its change by 4 a.m. Day/Date models have Bi-Lingual day
settings; if you select English, the watch will continue to display in English.

QUARTZ ANALOGUE OPERATING INSTRUCTIONS WITH DATE:
6P29 / 6P20 / 6P21
Positions: A B C
Day
24 hour display
Date
Positions: A B C
Day
Age of the moon
Date

Quartz Analogue Operating Instructions With Date: 6P29 / 6P20 / 6P21
To set the time/day:
1. Gently pull out crown to Position C.
2. Turn crown either way to set the time.
3. Push in crown to Position A.
To set the day of the week:
1. Gently pull out crown to Position C.
2. Turn crown clockwise to advance the hour hand by 24 hours per day.
3. Push in crown to Position A.

Quartz Analogue Operating Instructions With Date: 6P29 / 6P20 / 6P21
To set the date:
1. Gently pull out crown to Position B.
2. Turn crown anti-clockwise to adjust date.
3. Push in crown to Position A.
To set the moon age:
Note: More accurate settings can be made during a new moon (when the
centre of the moon aligns to ‘0’ on the scale) or during a full moon (when
the centre of the moon aligns to ‘15’ on the scale)
1. Gently pull out crown to Position B.
2. Turn crown clockwise to adjust the moon age.
3. Push in crown to Position A.
0
.
.
.
.
5
.
.
.
.
1
0
.
.
.
.
2
0
.
.
.
.
2
5
.
.
.
.

Quartz Analogue Operating Instructions With Date: 6P29 / 6P20 / 6P21
To read the moon age:
Note: The age of the moon is determined by the period between each new
moon. This period is approximately 29.5 days. The moon dial can be used
as a guide to moon phase and tides.
New Moon
Moon’s age: 0
Spring tide
First quarter
moon
Moon’s age: 7
Neap tide
Full Moon
Moon’s age: 15
Spring tide
Last quarter
moon
Moon’s age: 22
Neap tide

QUARTZ ANALOGUE OPERATING INSTRUCTIONS WITH DATE:
6P27 / 6P77
Day
(of the week)
Hour hand
24 hour hand
Second hand 1st position
2nd position
Date Minute hand
Normal crown position

Quartz Analogue Operating Instructions With Date: 6P27 / 6P77
Setting the day:
1. Pull the crown to the 2nd position to stop the second hand
at 0 (12 o’clock).
2. Turn the hour/minute hands in a clockwise direction to set a day.
In order to set the day, you must advance the hour hand by
24 hours per day.
Note: Do not set the day by turning the crown in counter-clockwise
direction. The day changes somewhere between 0:00 a.m. and 5:30 a.m.
or a little later.