Accusplit Eagle AE120XLG User manual

2 3
4 5
6 7
2
Operating Instructions
ACCUSPLIT®EAGLE
AE120XLG
PEDOMETER
Functions
•Step counter.
•Automatic Activity Timer.
•Goal tracking for Steps, and Activity Time.
For complete Function Specifications, go to page 24.
Key Features
•Built around the Japanese-made JW200 PedometerEngine™
Step Sensor, the current gold standard for accuracy.
•Extra Large Digits.
•The ACCUSPLIT exclusive case makes this the slimmest
available pedometer built around the JW200 Step Sensor.
•Chromed, Spring Steel clip resists breakage.
•Case includes two leash slots, for attaching safety leash
on either side. Made from tough polycarbonate plastic.
•Step filter, can be set from 0-5 steps to further increase
accuracy.
HOW TO OPEN YOUR PEDOMETER
See diagrams at right.
The cover must be closed for the
pedometer to work.
USE IT NOW!
Your pedometer is preset with standardized settings
that allow you to use it now!You can customize the
settings later. Skip to pages 14-19 to use it now!
SETTING UPYOUR PEDOMETER
It’s a good idea to set up your pedometer before first using it.
You can change the daily Goal setting from Set mode.
See page 9 when ready to begin setting up your unit.
ACCUSPLIT
EAGLE
DigiwalkerXL.com
STEP TIME DIST CAL
SET
4728
MODE
RESET
S3– S1, S2, S4 S3+
190
XL
G
0 20% 40% 60%80%100%
Getting Acquainted
•Press the MODE button to cycle through the display
modes (Steps, ActivityTime, …)
See page 17 and Specifications for details.
•The RESET button sets your counts back to zero.
See page 19 for details.
MODES
•STEP: STEP mode shows step count.
•TIME: AUTO ACTIVITYTIMER MODE shows total
activity time in min and sec.
Both of the above also display progress towards user-defined
goal.
STEP TIME SET
80604020
0 100%
DIGI-WALKERXL.COM
120
XLG
S3- S3+S1,S2,S4
JW200
MY
GOAL
Mode
indicator
Goal
Display
Steps
Counted
MODE Button
SET Button
RESET Button
ACCUSPLIT, Inc.
3090 Independence Drive, Suite 148
Livermore, CA 94551 USA
800-935-1996 • 925-290-1900 • FAX [phone]
www.ACCUSPLIT.com • [e-mail]
Eat Right! Walk More! Live Well!
e ACCUSPLIT Lifestyle 970-079
Sept 07

10
8
11
9
12 13
15
Choosing Step and Time Goals: This unit can store
your personal goals for steps and activity time during step
activity.The default values are 3,500 steps and 30 minutes of
activity time. These are modest daily goals created with the
assumption that you will reset the unit daily. Most wellness
experts recommend that healthy people should work towards
10,000 steps and one hour of activity time each day. As your
activity level increases, you can change to more aggressive
goals at any time. Choose goals to fit your current activity
level.
SETTING PROCEDURE
ACCUSPLIT products use a common setting procedure
known as “S1- S2-S3-S4.” Here’s how it works:
Press S1 for 2 seconds: Enter the SET mode
Press S2: Change the field to be set
Press S3: Change the field value
Press S4 for 2 seconds: Exit the SET mode
You can enter and exit Set mode from any of the regular
display screens. Once in Set mode, you can cycle through all
of these settings by pressing S2 repeatedly:
Set Step Goal gSet ActivityTime Goal gSet Step Goal
We recommend that you adjust the settings all at once, using
the procedure below.
Entering set mode and setting Step Goal
1. Repeatedly press the MODE button until the pedometer
displays the current step count. (The display will show
a line underneath the word “STEP” on the label.)
2. Press and hold the S1 (SET) button for 2 seconds.
The step count display will start to flash, showing that
you’ve entered SET mode.The indicator bar will still be
underneath the word “STEP” on the label.You’ll also
notice the “G” indicator has come on, indicating that you
are ready to set your Step Goal.
3. Press the S3+ (MODE) button to increase the Step Goal
value. Press the S3– (RESET) button to decrease the Step
Goal. Hold the buttons down to change values quickly.
STEP TIME SET
80604020
0 100%
DIGI-WALKERXL.COM
120
XL
G
S3- S3+S1,S2,S4
JW200
MY
GOAL
G
Setting Step Goal Mode
“G” for
Goal
Setting
Steps
flash
while
setting
Step
Goal
4. Press the S2 (SET) button to select the next setting
(adjust the ActivityTime Goal).
Setting Activity Time Goal
1. (Continuing from above) - After pressing S2 (SET),
you will see the indicator bar shift to be underneath
“TIME” on the label.The “G” indicator will be on. The
display will show a flashing time, which is your Activity
Time Goal set point.
2. As before, press the S3+ (MODE) button to increase the
Activity Time Goal, and press the S3– (RESET) button to
decrease the ActivityTime Goal. Hold the buttons down to
change values quickly.
Note: If you need to go back and change some of the values,
simply press S2 (SET) to cycle through all of the set points
until you see the one you want to change.
Exiting Set Mode
Press and hold the S4 (SET) button for 2 seconds. The unit
will exit setting mode – no values will be flashing anymore.
Note: The unit will save any changes and exit set mode after
30 seconds unattended.
WEARING YOUR PEDOMETER
Gently slide the pedometer
onto your belt or the top edge
of your pants or skirt.
It should fit snugly and level,
above one knee.The strong
steel clip makes it easy.
Note: The pedometer should be as vertical as possible.
Walkers with larger stomachs may find it helpful to wear
the pedometer farther back on the body, toward one hip.
The cover must be closed for the pedometer to work.
To avoid losing or dropping your pedometer, use the
included leash and clip to fasten the pedometer securely
to your clothing.
yes
no
Attaching the Leash
1. Attach the pedometer to the leash by looping the thin
side of the leash through one of the leash slots on the
sides of the pedometer case, near the bottom of the unit.
2. Put the pedometer onto your clothing as discussed above.
3. Attach the alligator clip to a belt loop or the top edge of the
pants or skirt.
Note: You can also use a safety pin to fasten the leash to
your clothing, loop the leash through your belt or belt
loop, or use a badge holder.

18 19
16 17
20 21
22 23
VIEWING YOUR RESULTS
Once you put on your pedometer with the cover closed, it
will automatically begin to record your steps and activity
time. Repeatedly press the MODE button to cycle through the
pedometer modes:
STEPS gTIME gSTEPS
Activity time is counted automatically whenever steps are
being counted.
• TIME is time spent in step activity.
Note: For extra accuracy, the default Step Filter Setting is 1.
See page 21 to learn more.
GOAL TRACKING
As discussed in beginning of instructions, this unit keeps
track of your progress towards the Step andTime goals you
set. Progress is shown as a series of small bars appearing
on the bottom of the display, with each bar representing
5% of the total. For example, if you set your step goal to
4,000 steps, and you’ve walked 2,000 steps so far, the goal
indicator in STEP mode will show as 50% complete. Progress
towards each goal is shown on the corresponding screen
– for example, when viewingTIME, you will see both the time
traveled in hours and minutes, and also the progress towards
your time goal on the bottom of the display.
RESETTING YOUR PEDOMETER
Most people prefer to reset counts daily. To reset your
counts: From STEP or TIME mode, press and hold the yellow
RESET button for at least 2 seconds. You’ll see the values all
go back to zero.
OTHER SETTINGS
The Step Filter setting is accessed through a special “deep
set” mode.
To enter this mode, press and hold the S1 (SET) button for
4 seconds.The screen will display a flashing single digit.
CHANGING STEP FILTER SETTING
While the JW200 PedometerEngine™ Step Sensor is
extremely accurate, some people like to have the ability to
filter out false steps. Therefore, the unit has a variable setting
step filter, to allow fine-tuning to your specific preferences.
You can set the value to any value from 0 – 5 steps. For
example, if the filter is set to “3”, the unit will wait to start
counting steps until more than three steps have been taken in
less than five seconds.
Press S3+ (MODE) or S3– (RESET) to change the step filter
setting. Press and hold S4 (SET) for 2 seconds to exit Deep
Set Mode.
Note: The unit will save any changes and exit set mode after
30 seconds unattended.
Set Step Filter set point
STEP TIME SET
80604020
0 100%
DIGI-WALKERXL.COM
120
XL
G
S3- S3+S1,S2,S4
JW200
MY
GOAL
Can be set
from 0-5
steps
REPLACINGTHE BATTERY AND MASTER RESET
When the display starts to dim or goes blank, it is time to
replace the battery.
If the display is not uniformly dim or blank, and appears to
display “erroneous data”, do a Master Reset by pressing all
3 buttons simultaneously for 3 seconds and then release.
The display should go blank, then turn all segments on, then
display 0 steps in Step Mode.
Note: All the settings will return to their default setting values.
If you need to change the battery, the settings will also revert
to default settings.
Battery
First, loop leash
through slot on side
of pedometer
Next, clasp clothing
Or, loop a badge
holder, then
put into pocket
(Badge holder
not included)
Or, loop a belt
or belt loop
To replace the battery:
1. Insert a coin into the slot on the
bottom of the case, and twist to
loosen the faceplate. Remove
faceplate and set aside.
2. Locate the battery holder as seen
on sketch. Pull out the old battery,
and push a new LR-44 battery into the holder,
with positive terminal (+) facing up.
3. Snap faceplate back into place, hooking the bottom
two tabs first, then closing by pressing together at the
top two tabs.

26 27
24 25
SPECIFICATIONS, FEATURES, and FUNCTIONS
Description of Functions
• Counts Steps up to 99,999 then rollover.
• Keeps track of progress towards Step Goal (default setting
is 3500 steps, but can be set from 0-99,990 steps, in 100
step increments).
• CountsTime spent in step activity, up to 999 Min 59 sec,
then rollover. Automatically counts whenever step activity
is occurring.
• Keeps track of progress towards ActivityTime Goal
(default setting is 30 minutes, but can be set from 0-999
min, in 1 min increments).
• Adjustable Step Filter (default setting is 1 step, but can
be set from 0-5 steps) to increase step count accuracy.
REGISTER NOW Please return
your AE120XLG Registration to
the Repair Center address in the
warranty, and we will let you know
about future products.
Email (preferred)
User
NO-PROOF-OF-PURCHASE LIMITED WARRANTY
Free service for first year of ownership;
$12 fee for service thereafter. See label inside unit for date.
See www.ACCUSPLIT.com/support for details
INDEX
Battery, replacing . . . . . . . . . . . . . . . . . .22-23
Current day’s results, viewing . . . . . . . . . . 17
Set Mode, exiting .................... 13
GoalTracking ...................... 8,18
Open your pedometer . . . . . . . . . . . . . . . . . 4
SafetyLeash......................15-16
Setting Function . . . . . . . . . . . . . . . . . . . .9-13
Setting Step filter . . . . . . . . . . . . . . . . . .20-21
Wearing your pedometer . . . . . . . . . . . . . . 14
Warranty ........................... 25