Accusplit Eagle AE140XL User manual

2 3
4 5
6 7
2
Operating Instructions
ACCUSPLIT® EAGLE
AE140XL
PEDOMETER
Functions
•Step counter.
•Distance in mi or km.
For complete Function Specifications, go to page 24.
Key Features
•Built around the Japanese-made JW200 PedometerEngine™
Step Sensor, the current gold standard for accuracy.
•Extra Large Digits.
•The ACCUSPLIT exclusive case makes this the slimmest
available pedometer built around the JW200 Step Sensor.
•Chromed, Spring Steel clip resists breakage.
•Case includes two leash slots, for attaching safety leash
on either side. Made from tough polycarbonate plastic.
•Step filter, can be set from 0-5 steps to further increase
accuracy.
HOW TO OPEN YOUR PEDOMETER
See diagrams at right.
The cover must be closed for the
pedometer to work.
USE IT NOW!
Your pedometer is preset with standardized settings
that allow you to use it now!You can customize the
settings later. Skip to pages 13-16 to use it now!
SETTING UPYOUR PEDOMETER
It’s a good idea to set up your pedometer before first using it.
To record your distance accurately, you will need to set your
stride length.
See page 9 when you are ready to set up your unit.
ACCUSPLIT
EAGLE
DigiwalkerXL.com
STEP TIME DIST CALSET
4728
MODE
RESET
S3– S1, S2, S4 S3+
140S
XL
Getting Acquainted
•Press the MODE button to cycle through the display
modes (Steps and distance.)
See page 16 and Specifications for details.
•The RESET button sets your counts back to zero.
See page 17 for details.
MODES
•STEP: STEP mode shows step count.
•DIST: DISTANCE mode shows distance traveled (mi/km).
STEP DIST SET
DIGI-WALKERXL.COM
140
XL
S3- S3+S1,S2,S4
JW200
Mode
indicator
Steps
Counted
MODE Button
RESET Button (yellow)
ACCUSPLIT, Inc.
3090 Independence Drive, Suite 148
Livermore, CA 94551 USA
800-935-1996 • 925-290-1900 • FAX [phone]
www.ACCUSPLIT.com • [e-mail]
Eat Right! Walk More! Live Well!
e ACCUSPLIT Lifestyle 970-086
Nov 07

10
8
11
9
12 13
1514
SETTING PROCEDURE
ACCUSPLIT products use a common setting procedure
known as “S1- S2-S3-S4.” Here’s how it works:
Press S1 for 2 seconds: Enter the SET mode
Press S2: Change the field to be set
Press S3: Change the field value
Press S4 for 2 seconds: Exit the SET mode
You can enter and exit Set mode from any of the regular
display screens.
Entering set mode
Press and hold the S1 (MEMORY) button for 2 seconds.
The display will start to flash, showing that you’ve entered
SET mode.
Setting Stride Length
1. You will see the mode indicator bar underneath DIST
and the “in” indicator come on. The display will show
a flashing number, which is your Stride Length set point
(in inches).
2. Press the S3 + (MODE) button to increase the Stride
Length (in increments of ¼ inch), and press the S3-
(RESET) button to decrease the Stride Length. Hold
the buttons down to change values quickly.
Finding Your Stride Length: Your stride length is the
length of one of your steps, measured from “toe to toe.”To
measure, walk 10 steps with your normal stride and measure
theTOTAL DISTANCE from the toe of your starting step to
the toe of your 10th step (see diagram below). Divide the
TOTAL DISTANCE by 10, and multiply the decimal portion by
12 to find your stride length in feet and inches. Example:You
walk 23 feet and 6½ inches in 10 steps. Convert to feet only =
23.542 feet (6½ ÷ 12 = 0.542). Divide by ten to get the stride
length in feet = 2.354 feet. Now, convert back to feet and
inches to get your stride length = 2 feet 4.25 inches (0.354 ×
12 = 4.25).
10 steps
Exiting Set Mode
Press and hold the S4 button for 2 seconds. The unit will exit
setting mode – no values will be flashing anymore.
Note: The unit will save any changes and exit set mode after
30 seconds unattended.
WEARING YOUR PEDOMETER
Gently slide the pedometer
onto your belt or the top
edge of your pants or skirt.
It should fit snugly and
level, above one knee.The
strong steel clip makes it
easy.
Note: The pedometer should be as vertical as possible.
Walkers with larger stomachs may find it helpful to
wear the pedometer farther back on the body, toward
one hip.
The cover must be closed for the pedometer to work.
yes
no
To avoid losing or dropping your pedometer, use the included
leash and clip to fasten the pedometer securely to your
clothing.
Attaching the Leash
1. Attach the pedometer to the leash by looping the thin
side of the leash through one of the leash slots on the
sides of the pedometer case, near the bottom of the unit.
2. Put the pedometer onto your clothing as discussed above.
3. Attach the alligator clip to a belt loop or the top edge of the
pants or skirt.
Note: You can also use a safety pin to fasten the leash to
your clothing, loop the leash through your belt or belt
loop, or use a badge holder.
First, loop leash
through slot on side
of pedometer
Next, clasp clothing
Or, loop a
badge holder, then
put into pocket
(Badge holder
not included)
Or, loop a belt
or belt loop
STEP DIST SET
DIGI-WALKERXL.COM
140
XL
S3- S3+S1,S2,S4
JW200
in
Setting Stride Length
Stride
Length
Flashes
“in” indicator
for inches

To replace the battery:
1. Insert a coin into the slot on the
bottom of the case, and twist to
loosen the faceplate. Remove
faceplate and set aside.
2. Locate the battery holder as seen
on sketch. Pull out the old battery,
and push a new LR-44 battery into the holder,
with positive terminal (+) facing up.
3. Snap faceplate back into place, hooking the bottom
two tabs first, then closing by pressing together at the
top two tabs.
18 19
16 17
21
22 23
VIEWING YOUR RESULTS
Once you put on your pedometer with the cover closed, it
will automatically begin to record your steps, activity time,
and distance. Repeatedly press the MODE button to cycle
through the pedometer modes:
STEPS gDISTANCE gSTEPS
Distance is counted automatically whenever steps are being
counted.
• DISTANCE is simply stride length x steps.
Note: For extra accuracy, the default Step Filter Setting is 1.
See page 19 to learn more.
20
RESETTING YOUR PEDOMETER
Most people prefer to reset counts daily.To reset your counts:
From STEP or DISTANCE mode, press and hold the yellow
RESET button for at least 2 seconds.You’ll see the values all
go back to zero.
OTHER SETTINGS
The Step Filter and Unit of Measurement settings are
accessed through a special “deep set” mode.
To enter this mode, press and hold the S1 button for 4
seconds.The screen will display a single digit. From within
Deep Set mode, press the S2 button to cycle back and forth
between the Step Filter set point and Choice of Unit System.
CHANGING STEP FILTER SETTING
While the JW200 PedometerEngine™ Step Sensor is
extremely accurate, some people like to have the ability to
filter out false steps. Therefore, the unit has a variable setting
step filter, to allow fine-tuning to your specific preferences.
You can set the value to any value from 0 – 5 steps. For
example, if the filter is set to “3”, the unit will wait to start
counting steps until more than three steps have been taken in
less than five seconds.
Press S3+ (MODE) or S3– (RESET) to change the Step Filter
Setting.
CHANGING UNITS (English vs. Metric)
The Pedometer can display either in English units (in, mi, and lb
- this is the default), or in Metric units (cm, km, and kg). From within
Deep Set mode (see pg. 18), press the S2 button to cycle back and
forth between setting the Step Filter set point and Choice of Unit
System.The unit will show either “US” or “EU” (for European Union)
depending on the unit system chosen. If you change units after using
the pedometer, the unit will convert all of your data into the new unit
system when you exit Deep Set model.You can check to see which
system of units you are using by seeing which measurement units
are displayed on the Stride and Weight setting screens.
Press S3+ (MODE) or S3– (RESET) to change the Measurement Mode.
Press and hold S4 for 2 seconds to exit Deep Set Mode.
Note: The unit will save any changes and exit set mode after 30
seconds unattended.
REPLACINGTHE BATTERY AND MASTER RESET
When the display starts to dim or goes blank, it is time to
replace the battery.
If the display is not uniformly dim or blank, and appears to
display “erroneous data”, do a Master Reset by pressing all
3 buttons simultaneously for 3 seconds and then release.
The display should go blank, then turn all segments on, then
display 0 steps in Step Mode.
Note: All the settings will return to their default setting values.
If you need to change the battery, the settings will also revert
to default settings.
Set Step Filter set point
STEP DIST SET
DIGI-WALKERXL.COM
140
XL
S3- S3+S1,S2,S4
JW200
Set measurement mode
“US” (English)
or “EU” (Metric)
Can be set
from 0-5
steps
STEP DIST SET
DIGI-WALKERXL.COM
140
XL
S3- S3+S1,S2,S4
JW200
Battery

26 27
24 25
SPECIFICATIONS, FEATURES, and FUNCTIONS
Description of Functions
• Counts Steps up to 99,999 then rollover.
• Counts distance traveled during step activity, up to
999.99 mi or km, then rollover. Automatically counts
whenever step activity is occurring.
• Adjustable stride length for greater distance accuracy
(default setting is 21 in/53 cm, but can be set from 12-72 in
(30-180 cm), in 0.25 in / 1 cm increments.
• Adjustable Step Filter (default setting is 1 step, but can
be set from 0-5 steps) to increase step count accuracy.
• Switchable between English and Metric units, without
losing data (default setting is English units).
REGISTER NOW Please return
your AE140XL Registration to
the Repair Center address in the
warranty, and we will let you know
about future products.
Email (preferred)
User
NO-PROOF-OF-PURCHASE LIMITED WARRANTY
Free service for first year of ownership;
$12 fee for service thereafter. See label inside unit for date.
See www.ACCUSPLIT.com/support for details
Battery, replacing . . . . 22-23
Current day’s results,
viewing ..............16
Setting Mode, exiting . . . .12
Open your pedometer . . . .4
Safety Leash . . . . . . . . 14-15
Setting up pedometer. . 8-12
Step Filter Setting,
change . . . . . . . . . . . 18-19
Stride Length,
setting .............8-12
Unit of measure,
changing . . . . . . . . . . 18-21
Wearing pedometer . . . . .13
Warranty ..............25
INDEX