ACDC HFTV-1 User manual

FOR YOUR OWN SAFETY
1. Read all the instructions before using the fan heater.
2. Only connect the fan heater to a single-phase socket with a mains voltage as specified on the rating plate.
3. This appliance meets the electromagnetic compatibility requirements specified in EN 55104/95 with regard
to interference with radio and TV sets.
4. Do not leave your home while the appliance is in operation: ensure that the switch is in OFF(0) position
and the thermostat is in minimum position. Always unplug the appliance.
5. Keep combustible material such as furniture, cushions, bedding, paper, clothes, curtains etc. at least
100cm away from the fan heater.
6. If wall mounted, do not fix to a combustible material such as wood, synthetic or plastic surfaces. Do not
hang anything on or in front of the fan heater.
7. Always unplug the heater when not in use. Do not pull the cord to unplug the heater.
8. Keep the air inlet and outlet free from obstructions: at least 1m in front and 50cm behind the heater.
9. Do not install the heater directly below a socket.
10. Do not let animals or children touch or play with the fan heater. Pay attention! The air outlet gets hot during
operation (more than 8 0℃, or 175F).
11. Do not cover. If covered, there is the risk of overheating.
12. Do not use this fan heater in the immediate vicinity of a bath, a shower or a swimming pool.
13. Do not use this fan heater in areas where explosive gas is present or while using flammable solvents,
varnish or glue.
14. If the cord of this appliance is damaged, discontinue use of this product and contact the manufacturer for
further instructions.
15. Keep the fan heater clean. Do not allow any objects to enter the inlet or exhaust openings as this may
cause electric shock or fire damage to the heater.
INSTALLATION
The appliance requires no installation. It should be used solely as a portable appliance.
Portable appliances are not suitable for use in a bathroom.
OPERATION
- Turn the thermostat knob (right) in a clockwise direction until it reaches the maximum setting .
- Summer service(ventilation only): turn the knob to setting
- Heating at reduced power: turn the knob(right) to setting Ⅰ (1000W).
- Heating at full power: turn the(right) to setting Ⅱ (1200W)
- Switching off: turn the knob(left) to setting
REGULATING THE THERMOSTAT
When the room has reached the required temperature turn the thermostat knob (where included) in an
anti-clockwise direction up to the point where the appliance switches off and not beyond. The temperature

fixed in this way will be automatically regulated and kept at a constant level by the thermostat.
CLEANING AND MAINTENANCE
Before cleaning always remove the plug from the electrical socket.
Clean the air inlet/outlet grilles frequently.
Never use abrasive powders or solvents.
WARNINGS
- Do not use the appliance in the vicinity of showers, bath tubs, wash basins, swimming pools etc.
- Always use the heater in an upright position.
- Do not use the heater to dry your laundry. Never obstruct the intake and outlet grilles (danger of
overheating).
- The heater must be positioned at least 50cm from furniture or other objects.
- When the appliance is used as a portable unit, do not place it up against walls, furniture, curtains, etc.
- The appliance must be installed so that the switches and other controls cannot be reached by persons
using the bath tub or the shower.
- This appliance comes with a Y-type connection. Replacement of the feed cable can only be done by a
technician authorized by the manufacturer. Because such work requires special tools.
- The appliance must not be positioned directly underneath a fixed power point.
- Do not cover the appliance while it is functioning in order to avoid overheating with the attendant risk of fire.
- Do not use the appliance in rooms less than 4m
2
in area.
The heater is fitted with a safety device which will switch off the heater in case of accidental overheating ( e.g.
Obstruction of air intake and outlet grilles or motor turning slowly or not at all). To reset, disconnect the plug
from the power for a few minutes, remove the cause of overheating then plug the appliance in again.