Acme Furniture 21610Q User manual

Queen
Storage
Bed
MODEL
21610Q
DESCRIPTION:
Queen Headboard
Queen Footboard
Queen Side Rails
Queen Slat & Support Legs
Storage Drawer
INSTALLATION AREA
+
Caution : Please read instructions thoroughly before unpacking assembly parts.
Sharp, exposed staple tips can cause injury, therefore, for your protection,
please remove any exposed staples used in packing.
1. We recommend that you should assemble this product with the assistance of another person ;
this will make assembly easier, and will help to eliminate damage to the product or injury to
persons during assembly.
2. Be sure to check all packing materials carefully for small parts that may have come loose inside
the carton during shipment.
3. Please do not over tighten screws or bolts.
4. Please put all parts on a non - abrasive floor before assembly. and follow the assembly step to
assemble your newly purchased product correctly and efficiently .
Drawer N Q & N R are identical & compatible, to each other regardless left or right.
During assembly, do not tighten any hardware until the complete unit has beeb assembled.
2 PERSON
installation recommended
20 - 25
mins 20 - 25
minutes for installation
PAGE 1 OF 11
A
C
B
Assembly
Installation
Guide
+
=
!
N :R
N :R
N :Q

BOX 1
Box of Headboard & Footboard
Headboard x 1
255 x 1420 x 1593 mm Footboard x 1
42 x 570 x 1591mm
Triangle Support Panel x 2
-9 x 200 x 200
Hardware List
N 1
Flat Head Chipboard
Screw x 8
m4 x 32mm RBW
BOX 2
Box of Side rail Hardware List
BOX 3 & 4
Box of Parts & Hardware
PAGE 2 OF 11
N A N B
N C(L)
Headboard Drawer x 2
N A1
N C(R) N D
Headboard Leg (L) x 1 Headboard Leg (R) x 1
N E
Drawer Support Rail 2 x 4
20 x 40 x 633mm
N F
Support Leg 2 x 1
30 x 30 x 95mm
N G
Support Leg 3 x 1
30 x 30 x 107mm
N H
Side Rail x 2
39 x 570 x 2060mm
N I
Bed Slat x 3
18 x 45 x 1545mm
N J
F/Board Drawer Frame x 1
40 x 220 x 1545mm
N K
Concealed Panel x 5
9 x 295 x 2040mm
N L
H/Board Back Support 1 x 1
19 x 30 x 1559mm
N M
Drawer Support Rail x 1
30 x 30 x 1545mm
N N
Supprt Leg 1 x 5
30 x 30 x 518mm
N O
H/Board Back Support 2 x 1
18 x 45 x 1559mm
N P
Bed Slat With Marking x 2
18 x 45 x 1545mm
N 2
Pan Head Chipboard
Screw x 8
m3.5 x 20mm BLK
N 3
JCBC Bolt x 4
m6 x 35mm
BLK
N 4
JCBC Bolt x 2
m6 x 50mm
BLK
N 5
Spring Washer x 6
1/4" RBW
N 6
Flat Washer x 6
1/4" ID x 13mm OD
BLK
N 7
Allen Key x 1
m4 x 110mm BLK
N 8
Flat Head Chipboard
Screw x 16
m4 x 32mm RBW
N 9
Pan Head Chipboard
Screw x 27
m3.5 x 20mm BLK
N 10
JCBC Bolt x 15
m6 x 35mm
BLK
N 11
JCBC Bolt x 6
m6 x 50mm
BLK
N 12
Spring Washer x 15
1/4" RBW
N 13
Flat Washer x 15
1/4" ID x 13mm OD
BLK
N 15
Allen Key x 1
m4 x 110mm BLK
N 14
Z - Bracket x 1
N Q
Drawer 1 x 4
N R
Drawer 2 x 2
N 16
Handle x 8
N 17
Truss Head M.
Screw Handle x 4
m4 x 48mm BLK
N 18
Truss Head M.
Screw Handle x 4
m4 x 50mm BLK

A
Headboard
Assembly
Installation
Rotate the Headboard (A) down and
turn to back.
N A
Attach and tighten the Headboard Leg
L/R (C) to the Headboard (A).
Left
Right
Back
Insert Spring washer (5) , Flat Washer (6) , tighten JCBC bolt (3) by using
an Allen Key (7).
x4
Insert Spring washer (5) , Flat Washer (6) , tighten JCBC bolt (4) by using
an Allen Key (7).
x2
PAGE 3 OF 11
Box 1 : N A Box 1 : N C(L) + N C(R)
N C(L)
Left
Right
Box 1 : N 3 + N 5 + N 6 + N 7
N 7 N 3 N 5 N 6
N 4
Box 1 : N 4 + N 5 + N 6 + N 7
N 3
N A
N C(R)
N 7N 4N 5N 6
N 4N 3

PAGE 4 OF 11
A
Headboard
Assembly
Installation
Attach and tighten the triangle Support Panel (D) to the
Headboard and tighten the Panhead screw (2) using
screw driver . (Not included)
x8
x6
x2
Attach Headboard Back Support (L) & (O) as picture shown. Tighten
the CSK screw (1) using a screw driver. (Not included)
6.1
6.2
Box 1 : N D + N 2
N D
Box 1 : N 1
Box 2 : N L + N O
N C
N L
N L
N O
N C
N O
N 1
N 1
N 1
N 2N 1
N D
N 2
N 2N 1

PAGE 5 OF 11
B
Footboard
Structure
Assembly
Installation
Attach the Side Rail (H) to the Headboard Leg L/R (C). Insert Spring
Washer (12) , Flat Washer (13) , tighten JCBC (10) using
an Allen Key (15).
x4
Attach the Side Rail (H) to the Footboard (B). Insert Spring Washer (12) ,
Flat Washer (13) , tighten JCBC (10) using an Allen Key (15).
x4
Box 2 : N H + N 10 + N 12 + N 13 + N 15
N H
N 13
N 12
N 10
N 15
N C
N C
N H
Box 1 : N B
Box 2 : N 10 + N 12 + N 13 + N 15 N B
N 13
N 12
N 10
N B
N 15
N H
N H
N 11N 10
N 11N 10

PAGE 6 OF 11
B
Footboard
Structure
Assembly
Installation
Attach Support Leg (G) to the Footboard Drawer Frame (J). Insert Spring
Washer (12) , Flat Washer (13) , & tighten JCBC (10) using an Allen Key(15).
Box 1 : N G
Box 2 : N J + N 10 + N 12 + N 13 + N 15
N J
N G x1
N 15
N 10
N 12
N 13
N J
N G
Attach the Footboard Drawer Frame (J) to the Side Rail (H). Insert Spring
Washer (12) , Flat Washer (13) , tighten JCBC (10) using Allen Key (15).
Box 2 : N 10 + N 12 + N 13 + N 15
x2
N 13N 12N 10N 15
N J
N HN J
N H
N 11N 10
N 11N 10

PAGE 7 OF 11
B
Footboard
Structure
Assembly
Installation
Attach the Drawer Support Rail (E) to the Footboard (B) using CSK Screw (8)
and tighten with Screw Driver. ( Not included)
Box 1 : N E
Box 2 : N 8
N E
N B
N 8
x4
N B
N E
Attach the Drawer Support Rail (E) to the Footboard Drawer Frame (J). Insert
Spring Washer (12), Flat Washer (13) & tighten JCBC Bolt (10) using an Allen
Key (15).
Box 2 : N 10 + N 12 + N 13 + N 15
x4
N EN J
N J
N 9N 8
N 11N 10
N 15
N 10
N 12
N 13

PAGE 8 OF 11
B
Footboard
Structure
Assembly
Installation
Attach Support Leg 2 (F) to the Drawer support Rail (M). Tighten
JCBC Bolt (11) using an Allen Key (15)
Box 1 : N F
Box 2 : N M + N 11 + N 15
N 15
N 11
N M
N F
N F
N M
Attach Drawer Support Rail (M) to the Side Rail (H) using CSK Screw (8) and
tighten with Screw Driver. ( Not included)
Box 2 : N 8
x1
x2
N 8
N M
N M
N H
N 11N 10
N 9N 8

PAGE 9 OF 11
B
Footboard
Structure
Assembly
Installation
Attach Bed Slat (I) & (P) to the Bed Slat Support (N) . Tighten JCBC Bolt (11)
using an Allen Key (15). ( Loosen and tighten the Adjuster to
stability of bed)
Box 2 : N I + N N + N O + N P + N 11 + N 15
N 15
N 11
N I
N N
x3
N 15
N 11
N P
N N
x2
Attach Z-Bracket (14) to the Bed Slat Support (N) and Support Leg 2 (F). Use
Panhead Screw (9) and tighten with Screw Driver. ( Not included)
Box 2 : N 9 + N 14
N I
N N
N P
N N
N N
N F
N P
N I
N I
N I
N P
N N
N F
N 9
x2
N 14
N 11N 10
N 9N 8

PAGE 10 OF 11
C
Conceal
Panel & Drawer
Assembly
Installation
Slide Drawer - 2 (R) into position over Draer Support Rail -1 (M). Then slide Drawer - 1 (Q)
into position over Drawer Support Rail - 2 (E). Adjust the adjuster for alignment of drawer box.
Box 3 : N Q + N R
N M
N E
N R
N Q
N R
Install the handle (16) in the front or drawer (R). Tighten the Handle Screw (18) using Screw
Driver. (Not included)
Install the Handle (16) in front of drawer (Q). Tighten the Handle Screw
(17) using Screw Driver. (Not included)
Then Push together the Slide Rail (H) with Bed Slat (I) & tighten with
CSK Screw (8) by using Screw Driver. (Make sure the center of Bed Slat (I) is aligned with the
marked line as shown).
Box 2 : N 8
Box 3 : N 16 + N 17 + N 18
N 16
N 18
N R
N Q
N 8
N H
Marked Line
N I
x4
N 16
N 17
x4
x10
N 18N 17
N 18N 17
N 9N 8