Acolyte NEONLYTE User manual

1
Neonlyte
Installation manual

2
Please Read instructions fully prior to assembly
•These products may represent a potential shock or fire hazard if
improperly installed or attached in any way. Products
should be installed in accordance with these instructions, current
electrical codes and/or the current National Electric Code (NEC).
•Do not connect directly to high voltage power (120v-277v)!
•To avoid electrical shock, disconnect or disable power at the source
prior to installation or maintenance.
•To avoid electrical shock, use only with 12v or 24v DC hardwire or
plug in power supply. Factory warranty will be void if used otherwise
•To avoid product failure, pair the correct voltage power supply to
the correct voltage e.g., 24v with a 24v power supply. Factory
warranty will be void if used otherwise
•Do not use if there is any damage to the unit or to the power Cord’s
insulation. Inspect periodically.
•Ensure proper gauge wires are installed between Power Supplies,
Controls & Linear LED lighting to avoid voltage drop.

3
Available Neonlyte accessories
Aluminium Channel flexible silicone channel
Mounting clip
Milky Channel
Green Channel red channel blue channel

4
NOTE- Neonlyte is not Field Cuttable factory warranty will be void if any
alterations are made.
Metal channel installation
Step 1- install Neonlyte metal channel to solid structure.
Step 2 - Carefully unreel Neonlyte from cardboard reel (Avoid excessive
twisting)
Step 3–cut the cable tie holding the Neonlyte cable

5
Step 4 - Install Neonlyte channel into the metal channel by gently
pushing into position as shown ( Note: do not pull Neonlyte when
installing otherwise excessive length can occur).
Step 5 –Connect feed cable to power supply, switch on breaker and
test.

6
Flexible channel Installation
Step 1 - Carefully unreel Neonlyte from cardboard reel (Avoid excessive
twisting)
Step 2–cut the cable tie holding the Neonlyte cable
Step 3- Insert the Neonlyte into the flexible channel

7
Step 4 –secure the Neonlyte and flexible channel to a solid structure
using the mounting clips provided ensuring clip spacing is every 24
inches/2ft
Step 5 –Connect feed cable to power supply, switch on breaker and
test.

8
VOLTAGE DROP CHARTS
For best performance and lumen output, ensure proper wire gauge is installed to compensate for voltage drop of
low voltage circuits.
Example: 12V Voltage Drop & Wire Length Distance Chart
Wire
Gauge
10 W
.83 A
20 W
1.7 A
30 W
2.5 A
40 W
3.3 A
50 W
2.1 A
60 W
4.2 A
18 AWG
34 ft.
17 ft.
11 ft.
8 ft.
6 ft.
5 ft.
16 AWG
54 ft.
27 ft.
18 ft.
13 ft.
10 ft.
9 ft.
14 AWG
86 ft.
43 ft.
29 ft.
21 ft.
17 ft.
14 ft.
12 AWG
134 ft.
68 ft.
45 ft.
34 ft.
27 ft.
22 ft.
10 AWG
199 ft.
99 ft.
66 ft.
49 ft.
39 ft.
33 ft.
1Determine load size. Let’s assume load is 55W Round up to the nearest load.
2Determine distance from driver to load. Let’s assume the distance is 20ft
3 It’s Recommended to install 12AWG to eliminate excess voltage drop
12V Voltage Drop & Wire Length Distance Chart
Wire
Gauge
10 W
.83 A
20 W
1.7 A
30 W
2.5 A
40 W
3.3 A
50 W
2.1 A
60 W
4.2 A
18 AWG
34 ft.
17 ft.
11 ft.
8 ft.
6 ft.
5 ft.
16 AWG
54 ft.
27 ft.
18 ft.
13 ft.
10 ft.
9 ft.
14 AWG
86 ft.
43 ft.
29 ft.
21 ft.
17 ft.
14 ft.
12 AWG
134 ft.
68 ft.
45 ft.
34 ft.
27 ft.
22 ft.
10 AWG
199 ft.
99 ft.
66 ft.
49 ft.
39 ft.
33 ft.
24V Voltage Drop & Wire Length Distance Chart
Wire
Gauge
10 W
.42 A
20 W
.83 A
30 W
1.3 A
40 W
1.7 A
50 W
2.1 A
60 W
2.5 A
70 W
2.9 A
80 W
3.3 A
100 W
4. 2 A
18 AWG
134 ft.
68 ft.
45 ft.
33 ft.
27 ft.
22 ft.
19 ft.
17 ft.
14 ft.
16 AWG
215 ft.
109 ft.
72 ft.
54 ft.
43 ft.
36 ft.
31 ft.
27 ft.
22 ft.
14 AWG
345 ft.
174 ft.
115 ft.
86 ft.
69 ft.
57 ft.
49 ft.
43 ft.
36 ft.
12 AWG
539 ft.
272 ft.
181 ft.
135 ft.
108 ft.
90 ft.
77 ft.
68 ft.
56 ft.
10 AWG
784 ft.
397 ft.
263 ft.
197 ft.
158 ft.
131 ft.
112 ft.
98 ft.
82 ft.

9
Thank you for Purchasing Acolyte Products please visit
our website for the latest products
WWW.ACOLYTELED.COM