ACTi CAM-7300 series User manual

IP Outdoor Rugged Dome
(with DC 12V / PoE / AC24V)
CAM-7300 series
Ver. 070307
Quick Installation Guide

0-1
0Getting Started
1.1 PACKAGE CONTENTS
CAM-7300 series Power Adaptor (Option)
(DC12V / PoE / AC24V)
Product CD Terminal Blocks for Power, DI/O & Audio
Warranty Card Accessory
1

0-2
1.2 PHYSICAL DESCRIPTION

0-3

0-4
1. LAN
The IP Camera connects to the LAN (local area network) via a
standard RJ45 connector. Supporting NWAY, this IP outdoor
rugged dome can auto detect the speed of local network segment
(10Base-T/100Base-TX Ethernet).
2. WAN
The IP Camera connects to the WAN (wide area network) via a
standard RJ45 connector. Supporting NWAY, this IP outdoor
rugged dome can auto detect the speed of local network segment
(10Base-T/100Base-TX Ethernet).
3. Power Input
If your power input is DC12V. Please follow the description on
the connector to connect to power.
If your power input is AC24V. Please follow the description on
the connector to connect to power.
PIN NAME DESCRIPTION
1 N
2 L
AC Power Input
3 GND E-Ground of power
4. Analog Video Output
The IP outdoor rugged dome supports one channel analog video
output.
5. DI/O
PIN NAME DESCRIPTION
1 12V DC Power Input
2 GND Ground Pin

0-5
DI: To Trigger Logic Level 0: 0~0.4V; Normal Logic Level 1:
3.3~30V
DO: To Trigger Logic Level 0: 0.1~0.6V; Normal Logic Level1:
2.4~5V
6. Conduit Hole
These conduit holes are used for cables to go through.
7. Zoom Lever
Move this lever to adjust the optical zoom. After adjusting, rotate
it clockwise to fix it.
8. Focus Lever
Move this lever to adjust the Focus. After adjusting, rotate it
clockwise to fix it.
9. Video DC level Adjustment
Rotate it adjust the overall lighting for this camera.
10. CCD Functions DIP-switch
11. Reset Button
Step 1: Switch off IP device by disconnecting the power cable
Step 2: Press and continue to hold the Reset Button. Reconnect
the power cable while continuing to hold the reset button.
Step 3: Keep holding the reset button depressed around 6 seconds,
release the reset button. The unit will start up with factory default
settings.
PIN NAME DESCRIPTION
1 A_Out Audio Output
2 GND Ground Pin
3 A_In Audio Input
4 GND Ground Pin
5 DO Digital Output
6 GND Ground Pin
7 DI Digital Input
Item Description ON OFF
AES Auto Electric Shutter Default
BLC Backlight Compensation Default
AGC Auto Gain Control Default
F.L. Flickerless Default

0-6
1.3 INSTALLATION PROCEDURE
There are three types of installation of this IP outdoor rugged dome series.
Surface mount Flush mount Wall mount
Pictures
Optional Bracket
required
●●
The mounting procedure can be divided into two parts,
1st: Connect the IP outdoor rugged dome series
2nd: Mount the IP outdoor rugged dome series
1.3.1 Connect the IP Outdoor Rugged Dome
1.3.1.1 Remove the cover
Remove the dome cover with special hex wrench in the accessory bag.
1.3.1.2 Insert the cable
There are two conduit holes, one is at the dome bottom and the other one is
at the side of rugged dome with plug. Remove the plug if your cable will go
through the one at the side of rugged dome

0-7
1.3.1.3 Connect cables to connectors
Please follow the instruction at Chapter 2: Physical Description, for how to
connect to each connector.
1.3.1.4 LED Description
There are three LEDs in the system. They are indicators for power, fan and
heater respectively. According to operating temperature, the different LED
will be lighted for different situation.

0-8
NOTE: Temperatures indicate here is spec for internal IC temperature,
not for operating temperature.

0-9
1.4 Mount the IP Outdoor Fixed Dome (Surface)