ACTi CAM-5130 User manual

Day & Night IP
Zoom Camera
CAM-5130/CAM-5140/CAM-5150
Ver. 061030
Quick Installation Guide

1-1
1 Getting Started
1.1 PACKAGE CONTENTS
CAM-5130 CAM-5140/CAM-5150
Indoor D&N IP Zoom Camera Outdoor D&N IP Zoom Camera
Product CD WarrantyCard
Terminal Blocks Power Adaptor (Option)
1

1-2
1.2 Installation
1.2.1 How to set up
Remove the rear cover
1.2.2 Physical description
1. LAN Port & WAN Port
PIN NAME DESCRIPTION
1 LRX+ LAN RX+
2 LRX- LAN RX-
3 LTX- LAN TX-
4 LTX+ LAN TX+
5 WTX- WAN TX-

1-3
6 WTX+ WAN TX+
7 WRX- WAN RX-
8 WRX+ WAN RX+
2. DI/O & Video Output
PIN NAME DESCRIPTION
1 GND Ground Pin
2 DO Digital Output
3 GND Ground Pin
4 DI Digital Input
5 GND Ground Pin
6 Video_Out Analog Video Output
3. LAN Link LED Indicator
When the LAN Link LED light is on, the respective port is
connected to the 10/100Mbps Ethernet network.
4. LAN/WAN ACT LED Indicator
When the LAN Link LED light is on, the respective port is
connected to the 10/100Mbps Ethernet network.
5. WAN Link LED Indicator
When the LAN Link LED light is on, the respective port is
connected to the 10/100Mbps Ethernet network.
6. Action LED Indicator
When the Action LED light is on, the D&N IP Zoom Camera is
successfully completed the boot process.
7. Reset Button
Step 1: Switch off D&N IP Zoom Camera by disconnecting the
power cable
Step 2: Using a suitable pointed object, press and continue to hold
the Reset Button depressed. While continuing to hold the reset
button depressed, reconnect the power cable.
Step 3: Keep holding the reset button depressed around 6 seconds,
release the reset button. The unit will start up with factory default

1-4
settings.
8. Power Input
DC 12V input.
PIN NAME DESCRIPTION
1 DC12V Power Input (DC +12V)
2 GND Ground Pin
3 E-GND E-Ground Pin
1.2.3 Network cable pin define
EIA/TIA-568 defines two kinds of piecing specifications, EIA/TIA-568A
and EIA/TIA-568B. EIA/TIA-568A has already been eliminated, mostly
use EIA/TIA-568B at present, arrange the order as white orange, orange,
white green, blue, white blue, green, white brown, brown in its foot location,
as drawn:

1-5
The definition about Ethernet network card RJ-45 slot foot location is like the form:
Pin 10Base-T/100Base-TX Name Name
1 TX+ LTX+ WTX+
2 TX- LTX- WTX-
3 RX+ LRX+ WRX+
4 Have not used
5 Have not used
6 RX- LRX- WRX-
7 Have not used
8 Have not used

1-6
1.2.4 Water-proof corrugated tubing
Spec of “F1” is 10mm

1
1.3 CONNECT NECESSARY CABLES
The Ethernet cable and power cable are necessary for previewing function. Make sure all
cables are correctly and firmly connected.
1. Connect an analog monitor to D&N IP Zoom Camera video out (BNC connector).
2. Connect the power adaptor to D&N IP Zoom Camera
3. Connect D&N IP Zoom Camera’s LAN port to an Ethernet (RJ45 connectors)
4. Connect a PC to the Ethernet hub (RJ45 connectors)

2
2 Quick Tour
This section guides you with a quick tour on D&N IP Zoom Camera.
2.1 Configure the D&N IP Zoom Camera
2.1.1 Make sure network environment
Default IP of D&N IP Zoom Camera is 192.168.0.100. Please make sure the D&N
IP Zoom Camera and your PC are on the same network segment before running
the installation.
2
Please set the settings as below.
IP address: 192.168. 0.xxx
Subnet mask: 255.255.255. 0
(NOTE: xxx should be a number
from 1 to 254, but 100 is
excepted.)

3
2.1.2 Open Internet Explorer with IP address
NOTE: If your web browser is earlier than IE6, then download IE6 is
recommended.
NOTE: The D&N IP Zoom Camera default IP address is set to
192.168.0.100
2.1.3 Login with default administrator’s account & password
NOTE: Default administrator account is set to Admin, password is set to
123456, and click button.