ACTOR-MATE Rock Star AL12-05R User manual

Introduction
Thank you for purchasing Rock Star. Rock Star is a three-channel DMX laser which
can be controlled via a standard DMX controller. It is a lightweight, mini intelligent
fixture and is an ideal product for discos, clubs, exhibitions and any place that need
visionary effect. Rock Star provides 100 effects include text effects. For safe operation,
read this manual before powering or installing the fixture, follow the safety precautions
listed below, and observe all warnings printed in this manual and on the fixture.
Safety Precautions
Do not spill liquids in to or on to your unit. If this ever happens, disconnect the main
power immediately. Do not connect this unit to any dimmer pack.
Always disconnect from main power before making any type of connection.
Be sure to locate this unit in a place with adequate ventilation at least 15 cm from a
wall, and mount this unit in safe and stable matter.
To prevent fire or shock hazard, do not expose this unit to a high temperature or
high humidity area. Please unplug unit when not in use.
Always keep combustible materials away from the fixture.
Class 3B laser should be mounted at or above 3 meters height. Project Class 3B
laser light above eye level. Do not project Class 3B Laser light on specular material.
The entrance to area where Class3B laser is used should be posted with
appropriate warning signs.
This unit is intended for indoor use. Use of this unit outdoors voids all warranties.
Always refer service to a qualified technician. Never look directly into laser beam.
Occasional breaks are necessary to prevent breakdowns.
Caution - Use of controls or adjustments or performance of procedures other
than as specified herein may result in hazardous radiation exposure!
Set Up
Unpacking Rock Star comes with: 1 hanging bracket, 2 clamp levers, 2 washers,
1 power cord, and 1 user guide. Unpack carefully and be sure that no damage has
occurred during shipping. If there is anything missing or appear to be damaged
please contact your dealer.
Power Connection Be sure the source voltage in your area matches the required
voltage for your Rock Star before plugging your unit in. Incorrect voltage selection
will detrimentally affect the operation of this product.
DMX Cable Connection Rock Star is a three-channel DMX fixture that can be
operated with universal DMX controller. This unit and DMX controller require a
standard 3-pin XLR connector for data input and data output.
Installation/Mounting Rock Star should be properly mounted by using a suitable
hanging clamp and safety cable. Use in a well-ventilated area. Be sure no
ventilation slots are blocked.
Specifications
Product Name Rock Star
Model No. AL12-05R/ 30R/ 50R/ 100R/ 200R AL12-60B
Laser Diode 4.9/ 30/ 50/ 100/ 200mW 60mW
Laser Color Red Blue
Model No. AL12-05G/ 20G/ 30G/ 50G/ 100G/ 200G/ 300G/ 500G
Laser Diode 4.9/ 20/ 30/ 50/ 100/ 200/ 300/ 500mW
Laser Color Green
Net Weight 4Kgs
Power AC 100V~120V or 220V~240V 50/60HZ
Classification 4.9~50mW: 3R/ 100~500mW: 3B
Size (mm) L180 ×W240 ×H165
Fuse 20mm×2A
Housing Metal
Beam Divergence < 1.5 mrad
Operating temperature 18℃~25℃

Trouble Shooting
If there is no light from the unit, please check the main power supply and fuse.
If unit does not respond to DMX, please check the DMX cables are connected
properly and are wired correctly.
If unit does not response to the music please adjust the sound-active sensitivity level
by Sensitivity Adjustment Knob.
If problems cannot be solved please contact your dealer for service
Fuse Replacement
Always disconnect from main power supply before attempting to replace the fuse
Remove the old fuse from the holder and replace with the exact same type fuse.
Replacement with anything other than the specified part may damage your unit.
Cleaning
Use a soft cloth and normal glass cleaner to clean the outside casing. Cleaning
frequency depends on the environment in which the fixture operates. Be sure to dry
all parts before plugging the unit back in.
Operating Modes
1. Stand-Alone Operation (Sound Active Mode)
Sound Active mode
This unit has built-in program that will react to sound and music under Sound
Active mode. Set all DIP switch pins to OFF to run Sound Active mode
2. DMX Operation
DMX operation gives the users freedom to create their own programs tailored to
their own individual needs.
To run this unit in DMX mode, connect the unit to any standard DMX controller
via XLR connectors.
Please consult DMX controller manual to determine address.
DMX Signal Levels
Channel 1 Channel 2 Channel 3
Laser pattern and effect
controls
Movement speed control.
Channel-2 is functional only
when value at channel-1 is
set between 100 and 189.
Value Effect Value Speed
0-1 OFF 0-42
2-99 49 patterns 43-85
100-189 45 animations 86-128
190-255 Sound Active 129-171
172-214
215-255
FAST
SLOW
Line effect control. User
can change the patterns
to dot-line patterns by
control this channel.
e.g.
Function Selection Chart
DIP SWITCHES CHART
12345678910
FUNCTION
OFF OFF OFF OFF OFF OFF OFF OFF OFF SOUND MODE
SETADDRESS DMX MODE

Control Panel Introduction
1Power Cord Connection 2Fuse 3Power Switch
4Sensitivity Adjustment Knob 5Microphone 6DMX In & Out
7DIP Switch Pin jInterlock connector kKey control
Safety Label Position
Bottom
Front Panel
Identification label
Certification label
Warning label
Aperture label
5
4
1
2
3
6
7
1 2 4 8 16 32 64 128 256 .
OFF
ON
DMX 512 Address
jk
ON
OFF

Rock Star
AL12 Series User Manual
Your Best Mate
in Laser Lighting! ©2003 ACTOR-MATE CO., LTD.
No.15, Lane 83, Lungshou St.,
Taoyuan City, Taiwan 330. R.O.C.
Tel:[phone] / Fax:[phone]
www.actlaser.com.tw [e-mail]