adapt X1 Wall Track User manual

*Professional installation is highly recommended
X1 Wall Track
Installation Instructions
IMPORTANT WALL TRACK SAFETY NOTICE
•To use the X1 requires the installation of the provided Wall Track. *
•Do not commence installation until you have read and understood the instructions and
warnings contained in this installation sheet.
•Professional installation is highly recommended.
•Improper installation or use of the X1 or Wall Track may cause damage or serious injury.
•Be aware of electrical wiring before any drilling or screwing into walls.
•Only mount the Wall Track to a structural wall or structural stud. Examples of structural
walls include:
oSolid walls (brick, masonry) or
oPlaster walls with approved structural stud
•If mounting to timber or steel wall studs, make sure that the mounting screws are anchored
into the centre of the studs. Use of a stud finder is highly recommended.
•The wall must be flat. If the Wall Track is not installed onto a flat surface then it will be
difficult to use the X1 properly.
•Due to forces experienced by the Wall Track when the X1 is in use, each screw must be
installed firm and tight.
•Regularly check each screw is firm and tight in Wall Track. Tighten each Wall Track screw
as required.
•Do not conduct the Wall Track installation process within 5m (16ft) of others as this will
present a safety risk.
•Any personal or property damage or injury caused by a lack of personal care or not
following the instructions fully is not covered by the warranty.
•Do not place the X1 or the Wall Track in the following environments:
oAn area of high humidity such as a bathroom
oNear any heat source such as stoves and other devices that produce heat
oNear kitchen counters
oAn area exposed to wind or rain
oDo not install in excessively dusty places

*Professional installation is highly recommended
Required Tools
(not supplied with X1):
•Power Drill
•Stud finder (not required for brick or masonry wall)
•Phillips Head Screw Driver Bit No 2
•Spirit Level
Included Parts
(supplied with X1):
Image:
a. Wall Track (3 Pieces)
b. Top Piece of Track (1 Piece)
c. Track Connectors (6 Pieces)
d. Bottom Piece of Track (1 Piece)
e. Steel Drill Bit (1 Piece)
f. Masonry Drill Bit (1 Piece)
g. Grub Screws
h. Hex Key for Grub Screws (1 Key)
i. Screws (10 Screws)
j. Solid Wall/Steel Stud Plugs (10 Plugs)

*Professional installation is highly recommended
WALL TRACK INSTALLATION GUIDE
Please note –The Wall Track installation guide is provided to support
professional installation of the wall track. A professional installer must satisfy
themselves that the Wall Track has been secured appropriately.
Step 1 –Assemble the Wall Track:
a. There are three (3) pieces of Wall Track in the box plus the Top Piece (1) and
Bottom Piece (1) of Track
b. We recommend you use all three pieces of Wall Track however you may choose to
only use two pieces. (Each piece of Wall Track is 50cm long)
c. Find a flat surface (like the floor) to put the Wall Track down with the front of Wall
Track face down
d. Select one piece of Wall Track and insert two track connectors into each end (4 in
total). Secure them firmly with the provided grub screws (see Image 1)
e. Turn this piece (upside down –with the grub screws facing upwards) in the centre of
the floor and connect the remaining two pieces of wall track to each end (see Image
2)
f. Add the Top Piece of Track to one end of the Wall Track. Secure firmly with the
provided grub screws (see Image 2)
g. Add the Bottom Piece of Track to the other end of the Wall Track. Secure firmly with
the provided grub screws (see Image 2)
h. The Wall Track should now be fully connected. Please ensure that all grub screws (8
total) are tight and the Wall Track is fully connected together in a very tight manner.
Carefully turn the Wall Track over (see Image 3)
i. Note –be very careful to support the Wall Track at the connection points if it is
carried to the installation location
Image 1:
Image 2:
Image 3:

*Professional installation is highly recommended
Step 2 - Find the right location:
a. A minimum of 0.5m (20in) of side space and 2.0m (6ft 7in) of floor space around the
X1 for training (see Image 4)
b. A structural wall or structural stud (as described above) –To be clear; if you are
installing onto a plaster wall you must install screws into the wall stud
c. A flat surface where you can achieve a firm and tight Wall Track installation
Image 4:
0.5m (20”)
2.0m (6’7”)
0.5m (20”)

*Professional installation is highly recommended
Step 3 - Determine the Wall Track position:
a. Place the Wall Track on the selected wall. Please ensure that the grub screws have
been tightened to keep the track together
b. The bottom of the Wall Track should be 30cm (12in) from the floor. Ensure that it
is not lower than 30cm from the floor (see Image 5)
c. Once you have finalised the Wall Track position we recommend you make a mark for
the first screw hole with a pencil (see Image 6)
Start Here
Image 5:
Image 6:
30cm (12”)
30cm (12”)

*Professional installation is highly recommended
Step 4 - Solid Wall (masonry / brick / concrete) Install Instructions:
a. Before install ensure that you have found the right location (step 2) and positioned
the Wall Track correctly (step 3)
b. If you are drilling into a brick or masonry wall use the supplied masonry drill bit.
Ensure you do not drill into the mortar as this will not be strong enough. Ensure
surface is flat.
c. Drill a hole a minimum depth of 4cm (1 ½”)
d. Put the Wall Track back onto the wall, and push the supplied wall plug into the track
hole. The wall plug should push all the way into the track (you may need to use
something to push it all the way such as a screwdriver)
e. Tighten the screw into the wall plug which will tighten the Wall Track onto the wall
(we recommend the top hole in the middle section of track). Screw the Wall Track on
firmly but not completely tight
f. Using the spirit level ensure that the Wall Track is vertical. Move the Wall Track so
that it is level and tighten the screw to firm. Do not over-tighten. The Wall Track
should hold onto the wall with just 1 screw temporarily whilst the remaining screws
are affixed
g. Drill the remaining holes. The holes can be drilled through the Wall Track holes but
ensure you do not damage the Wall Track holes when drilling
h. To complete installation we suggest an absolute minimum of 7 screws and wall plugs
be used as indicated
i. Once the Wall Track is secured to the wall ensure that all screws are tightened to
firm but do not over-tighten

*Professional installation is highly recommended
Step 4 - Plaster Wall (with steel studs) Install Instructions:
a. Before install ensure that you have found the right location (step 2) and positioned
the Wall Track correctly (step 3)
b. Use the stud finder to find the stud
c. Use the supplied Steel Drill Bit
d. Drill the installation hole into the centre of the stud
e. Drill a hole a minimum depth of 4cm (1 ½”)
f. Put the Wall Track back onto the wall, and push the supplied wall plug into the track
hole. The wall plug should push all the way into the track (you may need to use
something to push it all the way such as a screwdriver)
g. Tighten the screw into the wall plug which will tighten the track onto the wall (we
recommend the top hole in the middle section of Wall Track). Screw the Wall Track
on firmly but not completely tight
h. Using the spirit level ensure that the Wall Track is vertical. Move the Wall Track so
that it is level and tighten the screw to firm. Do not over-tighten. The Wall Track
should hold onto the wall with just 1 screw whilst the remaining screws are affixed
i. Drill the remaining holes. The holes can be drilled through the Wall Track holes but
ensure you do not damage the Wall Track holes when drilling
j. To complete installation we suggest an absolute minimum of 7 screws and wall plugs
be used as indicated
k. Once the Wall Track is secured to the wall ensure that all screws are tightened to
firm but do not over-tighten

*Professional installation is highly recommended
Step 4 - Plaster Wall (with timber studs) Install Instructions:
a. Before install ensure that you have found the right location (step 2) and positioned
the Wall Track correctly (step 3)
b. Use the stud finder to find the stud
c. No hole drilling or wall plugs should be required for a timber stud (just the screw
itself)
d. Put the Wall Track back onto the wall, and screw the track onto the wall (we
recommend the top hold in the middle section of track). Screw the track on firmly but
not completely tight
e. Using the spirit level ensure that the Wall Track is vertical. Move the track so that it is
level and tighten the screw to firm. Do not over-tighten. The Wall Track should hold
onto the wall with just 1 screw whilst the remaining screws are affixed
f. To complete installation we suggest an absolute minimum of 7 screws be used as
indicated
g. Once the Wall Track is secured to the wall ensure that all screws are tightened to
firm but do not over-tighten