Precor CW-816 User manual

CW-816


CW-816 Assembly Guide
page 3
IMPORTANT SAFETY INSTRUCTIONS
Important Safety Instructions
Important Safety Instructions
When using exercise equipment, basic precautions
should always be taken, including the following:
• Readallinstructionsbeforeassemblingthe
CW-816. These instructions are written for your
safety and to protect the unit.
• Readeachstepintheassemblyinstructionsand
follow the steps in sequence. Do not skip ahead. If
you skip ahead, you may learn later that you have
to disassemble components and that you may
have damaged the equipment which would void the
Precor Limited Warranty.
• AssembleandoperatetheCW-816 on a solid, level
surface. Locate the unit a few feet from walls or
furniture to provide easy access.
• Donotallowchildrenorthoseunfamiliarwithits
operation on or near the equipment. Do not leave
children unsupervised around the unit.
• Usetheequipmentonlyforitsintendedpurpose.
Do not use accessory attachments that are not
recommended by the manufacturer, as such
attachments may cause injuries.
• DonotattempttoservicetheCW-816yourself.The
unit does not contain any user-serviceable parts.
Obtaining Service
For information about product operation or service,
refer to the Precor web site at www.precor.com where
you can also find customer support numbers or a list of
Precor authorized service centers.
If you contact Customer Support, have the serial
number available.
You can find the serial number printed on a label
affixed to the CW-816. For future reference, write the
serial number in the space provided below.
Serial number: _______________________

CW-816 Assembly Guide
page 4
Table of Contents
1
2
Important Safety Instructions .................................................................................. 3
Obtaining Service...................................................................................................................................... 3
Preparations............................................................................................................... 5
UnpackingtheEquipment ......................................................................................................................... 5
RequiredTools ......................................................................................................................................... 5
InstallationRequirements.......................................................................................................................... 5
Hardware Kit ............................................................................................................................................. 6
Assembly Instructions .............................................................................................. 7
Open the Box ........................................................................................................................................... 7
AssembletheUnit ..................................................................................................................................... 8
CleantheUnit ........................................................................................................................................... 9
Specifications............................................................................................................................... Back cover
Table of Contents

CW-816 Assembly Guide
page 5
1Preparations
Preparations
The CW-816 parts are inspected before shipment.
Eachunitcontainsseveralpiecesthatrequire
assembly.You may find it helpful to ask for assistance
during the assembly process.
Unpacking the Equipment
When you open a box, carefully unpack the pieces and
lay them on the floor near the location where you plan
to use them.
CAUTION: Be careful when you remove the
packaging material with a utility knife. Do not
scratch the paint.
If any items are missing, contact the dealer from whom
you purchased the unit. For more information, refer to
Obtaining Service.
Required Tools
Tools that you need to obtain before assembling the
unit include:
❏Wire cutter or utility knife
Installation Requirements
Follow these installation requirements when
assembling the unit:
• Review the Important Safety Instructions.
• Assemble the unit where it will be used.
Provide ample space around the unit.
• Install components in the sequence shown.
•Insert all fasteners in the same direction.
For aesthetic purposes, insert all the fasteners
in the same direction unless specified (in text or
illustrations) to do otherwise.
• Leave room for adjustments. Tighten the
fasteners to keep the unit stable, but leave room
for adjustments. Do not fully tighten fasteners until
instructed to do so.

CW-816 Assembly Guide
page 6
½x1¼-inchButtonheadscrew(A) 3
½-inch Washer (C) 5
½ x 1-inch Buttonhead screw (D) 2
³⁄₈x¾-inchButtonheadscrew(E) 8
Fastener Qty Fastener Qty
Hardware Kit
Preparations, continued
³⁄₈-inch Split washer (F) 8
½-inch Split washer (B) 5
Spacer (G) 3
Bumper (H) 6

CW-816 Assembly Guide
page 7
2Assembly
Instructions
Assembly Instructions
AssemblyoftheCW-816takesabout20minutesto
complete. If this is the first time you have assembled
this type of equipment, plan on allowing more time.
Be careful to open boxes and assemble components in
the sequence presented in this manual.
Note: With so many assembled parts, proper alignment
and adjustment is critical. While tightening the
fasteners, be sure to leave room for adjustments. Do
not fully tighten fasteners until instructed to do so.
Open the Box
Usewirecutterstoopentheboxandremovethe
packing materials.
The illustration shows how the CW-816 will look when
you have completed its assembly. The callouts identify
specific pieces.
Weight plate
holders
Upright Support
Stabilizer
Upright
Bumper

CW-816 Assembly Guide
page 8
Assemble the Unit
1. AttachtheUprightSupporttotheStabilizersusing
eight¾-inchbuttonheadscrews(E)
eight ³⁄₈-inch split washers (F)
Wrench tighten.
2. AttachtheUprighttotheUprightSupportusing
two 1-inch buttonhead screws (D)
two ½-inch split washers (B)
two ½-inch flat washers (C)
Wrench tighten.
3. Insert the three Weight Plate Holders into the
Upright.TurntheWeightPlateHolderssothe
mountingholesalignwiththeholesintheUpright.
4. Secure the Weight Plate Holders using
three1¼-inchbuttonheadscrews(A)
three ½-inch split washers (B)
three ½-inch flat washers (C)
three spacers (G)
Wrench tighten.
Note: For ease of assembly, place a split washer,
a flat washer, and a spacer onto each screw before
inserting the screw.
5. Slide a Bumper (H) onto each end of the Weight
PlateHolders,andpressrmlyagainsttheUpright.
Note: Make sure the small side of the Bumper
facestheUpright.
This completes the assembly of the CW-816.
Assemble the Unit
8 - ¾” buttonhead screws
8 - split washers
3 - 1¼” buttonhead screws
3 - split washers
3 - washers
3 - spacers
2 - 1” buttonhead screws
2 - split washers
2 - flat washer

CW-816 Assembly Guide
page 9
Clean the Unit
Clean the Unit
To clean the unit, moisten a clean, soft cloth in a mild
solution of soap and water and wipe all the parts
thoroughly.
Frequently vacuum the floor underneath the CW-816 to
prevent the accumulation of dust and dirt.

page10
Notes: