Adaptec Ultra Wireless Ultra Wireless Access Point User manual

R
Adaptec Ultra Wireless
TM
Access Point
User’s Guide

ii
Copyright
© 2002 Adaptec, Inc. All rights reserved. No part of this publication may be
reproduced, stored in a retrieval system, or transmitted in any form or by any
means, electronic, mechanical, photocopying, recording or otherwise, without the
prior written consent of Adaptec, Inc., 691 South Milpitas Blvd., Milpitas, CA 95035.
Trademarks
Adaptec, the Adaptec logo, and Ultra Wireless are trademarks of Adaptec, Inc.,
which may be registered in some jurisdictions.
Windows 98SE, Windows Me, Windows 2000, and Windows XP, are trademarks of
Microsoft Corporation in the US and other countries, used under license.
All other trademarks are the property of their respective owners.
Changes
The material in this document is for information only and is subject to change
without notice. While reasonable efforts have been made in the preparation of this
document to assure its accuracy, Adaptec, Inc. assumes no liability resulting from
errors or omissions in this document, or from the use of the information contained
herein.
Adaptec reserves the right to make changes in the product design without
reservation and without notification to its users.
Disclaimer
IF THIS PRODUCT DIRECTS YOU TO COPY MATERIALS, YOU MUST HAVE
PERMISSION FROM THE COPYRIGHT OWNER OF THE MATERIALS TO AVOID
VIOLATING THE LAW WHICH COULD RESULT IN DAMAGES OR OTHER
REMEDIES.

iii
Adaptec Technical Support
If you have questions about installing or using your Adaptec product, check this document
first—you will find answers to most of your questions here. If you need further assistance, use
the support options listed below.
Technical Support Identification (TSID) Number
■Before contacting Technical Support, you need your unique 12-digit TSID number. The TSID
number identifies your product and support status.
■The TSID number is included on two white, bar-coded labels, like the example below.
Support Options
■Search the Adaptec Support Knowledgebase (ASK) at ask.adaptec.com for articles,
troubleshooting tips, and frequently asked questions for your product.
■For support via Email, submit your question to Adaptec's Technical Support Specialists at
ask.adaptec.com.
■To order Adaptec products, including accessories and cables, call [phone]. Or, you
can order cables online at www.adaptec.com/buy-cables.
Europe
■Visit our Web site at www.adaptec-europe.com.
■German and English: Search the Adaptec Support Knowledgebase (ASK) at
ask-de.adaptec.com for articles, troubleshooting tips, and frequently asked questions for
your product.
For support via e-mail, submit your question to Adaptec's Technical Support Specialists at
ask-de.adaptec.com.
■French: Search the Adaptec Support Knowledgebase (ASK) at ask-fr.adaptec.com for articles,
troubleshooting tips, and frequently asked questions for your product.
For support via e-mail, submit your question to Adaptec's Technical Support Specialists at
ask-fr.adaptec.com.
■To order Adaptec products, including accessories and cables,
go to www.adaptec.com/buy-cables.
Australia and New Zealand
■Visit our Web site at www.adaptec.com.au.
■For support via e-mail, submit your question to Adaptec's Technical Support Specialists at
ask.adaptec.com.
Hong Kong and China
■Visit our Web site at www.adaptec.com.
■Fax Technical Support at [phone].
Singapore
■Visit our Web site at www.adaptec.com.
Japan
■Search the Adaptec Support Knowledgebase (ASK) at ask.adaptec.co.jp
■Visit our Web site at www.adaptec.co.jp.

iv
Limited 2-Year Hardware Warranty
1. Adaptec, Inc. (“Adaptec”) warrants to the purchaser of this product that it will be free from
defects in material and workmanship for a period of two (2) years from the date of purchase.
If the product should become defective within the warranty period, Adaptec, at its option,
will repair or replace the product, or refund the purchaser’s purchase price for the product,
provided it is delivered at the purchaser’s expense to an authorized Adaptec service facility
or to Adaptec.
2. Repair or replacement parts or products will be furnished on an exchange basis and will
either be new or reconditioned. All replaced parts or products shall become the property of
Adaptec. This warranty shall not apply if the product has been damaged by accident,
misuse, abuse or as a result of unauthorized service or parts.
3. Warranty service is available to the purchaser by delivering the product during the warranty
period to an authorized Adaptec service facility or to Adaptec and providing proof of
purchase price and date. The purchaser shall bear all shipping, packing and insurance costs
and all other costs, excluding labor and parts, necessary to effectuate repair, replacement or
refund under this warranty.
4. For more information on how to obtain warranty service, write or telephone Adaptec at 691
South Milpitas Boulevard, Milpitas, CA 95035, [phone].
5. THIS LIMITED WARRANTY DOES NOT EXTEND TO ANY PRODUCT WHICH HAS
BEEN DAMAGED AS A RESULT OF ACCIDENT, MISUSE, ABUSE, OR AS A RESULT OF
UNAUTHORIZED SERVICE OR PARTS.
6. THIS WARRANTY IS IN LIEU OF ALL OTHER EXPRESS WARRANTIES WHICH NOW
OR HEREAFTER MIGHT OTHERWISE ARISE RESPECT TO THIS PRODUCT. IMPLIED
WARRANTIES, INCLUDING THOSE OF MERCHANTABILITY, FITNESS FOR A
PARTICULAR PURPOSE AND NON-INFRINGEMENT SHALL (A) HAVE NO GREATER
DURATION THAN 2 YEARS FROM THE DATE OF PURCHASE, (B) TERMINATE
AUTOMATICALLY AT THE EXPIRATION OF SUCH PERIOD AND (C) TO THE EXTENT
PERMITTED BY LAW BE EXCLUDED. IN THE EVENT THIS PRODUCT BECOMES
DEFECTIVE DURING THE WARRANTY PERIOD, THE PURCHASER’S EXCLUSIVE
REMEDY SHALL BE REPAIR, REPLACEMENT OR REFUND AS PROVIDED ABOVE.
INCIDENTAL OR CONSEQUENTIAL DAMAGES, INCLUDING WITHOUT LIMITATION
LOSS OF DATA, ARISING FROM BREACH OF ANY EXPRESS OR IMPLIED WARRANTY
ARE NOT THE RESPONSIBILITY OF ADAPTEC AND, TO THE EXTENT PERMITTED BY
LAW, ARE HEREBY EXCLUDED BOTH FOR PROPERTY DAMAGE, AND TO THE
EXTENT NOT UNCONSCIONABLE, FOR PERSONAL INJURY DAMAGE.
7. SOME STATES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL
OR CONSEQUENTIAL DAMAGES FOR CONSUMER PRODUCTS, AND SOME STATES
DO NOT ALLOW LIMITATIONS ON HOW LONG AN IMPLIED WARRANTY LASTS, SO
THE ABOVE LIMITATION OR EXCLUSIONS MAY NOT APPLY TO YOU.
8. This warranty gives you specific legal rights, and you may also have other rights which vary
from state to state.

v
Adaptec Software License Agreement
PLEASE READ CAREFULLY: THE USE OF THIS SOFTWARE IS SUBJECT TO THE SOFTWARE
LICENSE TERMS OF ADAPTEC, INC. AND OTHER LICENSORS WHOSE SOFTWARE MAY
BE BUNDLED WITH THIS PRODUCT.
BY YOUR USE OF THE SOFTWARE INCLUDED WITH THIS PRODUCT YOU AGREE TO THE
LICENSE TERMS REQUIRED BY THE LICENSOR OF THAT SOFTWARE, AS SET FORTH
DURING THE INSTALLATION PROCESS. IF YOU DO NOT AGREE TO THE LICENSE
TERMS APPLICABLE TO THE SOFTWARE, YOU MAY RETURN THE ENTIRE UNUSED
PRODUCT FOR A FULL REFUND.
In return for acquiring a license to use the Adaptec software (“Software”) and the related
documentation, you agree to the following terms and conditions:
1. License. This Agreement grants you, the Licensee, a license to:
a. Use the Software on a single computer system or on multiple workstations, systems and
servers which incorporate an Adaptec RAID controller and may be accessed by multiple
users from multiple locations. You may make as many installations of the Software as
needed, but must restrict such installation only to systems, workstations or servers
using an Adaptec RAID controller.
b. Make one copy of the Software in machine readable form solely for back-up purposes
provided you reproduce Adaptec’s copyright notice and any proprietary legends.
2. Restrictions. You may not distribute copies of the Software to others. You may not post or
otherwise make available the Software, or any portion thereof, in any form, on the Internet.
You may not use the Software in a computer service business, including in time sharing
applications. The Software contains trade secrets and, in order to protect them, you may not
decompile, reverse engineer, disassemble, or otherwise reduce the Software to a human-
perceivable form. YOU MAY NOT MODIFY, ADAPT, TRANSLATE, RENT, LEASE, LOAN,
RESELL FOR PROFIT, DISTRIBUTE, NETWORK OR CREATE DERIVATIVE WORKS
BASED UPON THE SOFTWARE OR ANY PART THEREOF.
3. Ownership of Software. As Licensee, you own the media upon which the software is
recorded or fixed, but Adaptec and its licensors retain title and ownership of the Software
recorded on the original media and all subsequent copies of the Software, regardless of the
form or media in which or on which the original and other copies may exist. This license is
not a sale of the Software or any copy.
4. Confidentiality. You agree to maintain the Software in confidence and that you will not
disclose the Software to any third party without the express written consent of Adaptec. You
further agree to take all reasonable precautions to preclude access of unauthorized persons
to the Software.
5. Term. This license is effective until January 1, 2045, unless terminated earlier. You may
terminate the license at any time by destroying the Software (including the related
documentation) together with all copies or modifications in any form. Adaptec will have the
right to terminate our license immediately if you fail to comply with any term or condition
of this Agreement. Upon any termination, including termination by you, you must destroy
the Software (including the related documentation), together with all copies or
modifications in any form.
6. Special Terms Applicable to Databases. Where a database is included with the Software, you
acknowledge that it is licensed only in connection with the use of the Software to perform
disc creation, and that the database and all data derived therefrom must be maintained in
confidence in accordance with the provisions of Section 4. This license does not grant you
any rights to distribute or disclose such database or data.

vi
7. Limited Warranty. Adaptec and its Licensor warrant only that the media upon which the
Software is furnished will be free from defects in material or workmanship under normal
use and service for a period of thirty (30) days from the date of delivery to you. ADAPTEC
AND ITS LICENSORS DO NOT AND CANNOT WARRANT THE PERFORMANCE OR
RESULTS YOU MAY OBTAIN BY USING THE SOFTWARE OR DOCUMENTATION. THE
FOREGOING STATES THE SOLE AND EXCLUSIVE REMEDIES ADAPTEC AND ITS
LICENSORS WILL PROVIDE FOR BREACH OF WARRANTY. EXCEPT FOR THE
FOREGOING LIMITED WARRANTY, ADAPTEC AND ITS LICENSORS MAKE NO
WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING, BUT NOT LIMITED, AS TO
NON-INFRINGEMENT OF THIRD PARTY RIGHTS, MERCHANTABILITY OR FITNESS
FOR A PARTICULAR PURPOSE. Some states do not allow the exclusion of implied
warranties or limitations on how long an implied warranty may last, so the above
limitations may not apply to you. This warranty gives you specific legal rights and you may
also have other rights which vary from state to state.
8. The entire liability of Adaptec and its licensors, and your exclusive remedy for a breach of
this warranty, shall be:
a. The replacement of any media not meeting the above limited warranty which is
returned to Adaptec; or:
b. If Adaptec or its distributor is unable to deliver replacement media which is free from
defects in materials or workmanship, you may terminate this Agreement by returning
the Software and your money will be refunded.
9. Limitation of Liability. IN NO EVENT WILL ADAPTEC OR ITS LICENSORS BE LIABLE TO
YOU FOR ANY INCIDENTAL, CONSEQUENTIAL OR INDIRECT DAMAGES,
INCLUDING ANY LOST PROFITS, LOST SAVINGS, OR LOSS OF DATA, EVEN IF
ADAPTEC OR A LICENSOR HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH
DAMAGES, OR FOR ANY CLAIM BY ANY OTHER PARTY. Some states do not allow the
exclusion or limitation of special, incidental, or consequential damages, so the above
limitation or exclusion may not apply to you.
10. Export. You acknowledge that the laws and regulations of the United States and other
countries may restrict the export and re-export of the Software. You agree that you will not
export or re-export the Software or documentation in any form in violation of applicable
United States and foreign law.
11. Government Restricted Rights. The Software is subject to restricted rights as follows. If the
Software is acquired under the terms of a GSA contract: use, reproduction or disclosure is
subject to the restrictions set forth in the applicable ADP Schedule contract. If the Software is
acquired under the terms of a DoD or civilian agency contract, use, duplication or disclosure
by the Government is subject to the restrictions of this Agreement in accordance with 48
C.F.R. 12.212
of the Federal Acquisition Regulations and its successors and
49 C.F.R. 227.7202-1
of the DoD FAR Supplement and its successors.
12. General. You acknowledge that you have read this Agreement, understand it, and that by
using the Software you agree to be bound by its terms and conditions. You further agree that
it is the complete and exclusive statement of the agreement between Adaptec and you, and
supersedes any proposal or prior agreement, oral or written, and any other communication
between Adaptec and you relating to the subject matter of this Agreement. No additional or
any different terms will be enforceable against Adaptec unless Adaptec gives its express
consent, including an express waiver of the terms of this Agreement, in writing signed by an
officer of Adaptec. You assume full responsibility for the use of the Software and agree to
use the Software legally and responsibly. This Agreement shall be governed by California
law, except as to copyright matters, which are covered by Federal law. This Agreement is
deemed entered into at Milpitas, California by both parties. Should any provision of this
Agreement be declared unenforceable in any jurisdiction, then such provision shall be
deemed severable from this Agreement and shall not affect the remainder hereof. All rights
in the Software not specifically granted in this Agreement are reserved by Adaptec.
Should you have any questions concerning this Agreement, you may contact Adaptec by
writing to:
Adaptec, Inc.
Legal Department
691 South Milpitas Boulevard
Milpitas, California 95035.

vii
Regulatory Compliance Statements
Federal Communications Commission Radio Frequency Interference Statement
WARNING: Changes or modifications to this unit not expressly approved by the party
responsible for compliance could void the user’s authority to operate the equipment.
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses, and
can radiate radio frequency energy, and if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be determined by turning
the equipment off and on, the user is encouraged to try to correct the interference by one or more
of the following measures:
■Reorient or relocate the receiving antenna.
■Increase the separation between equipment and receiver.
■Connect the equipment to an outlet on a circuit different from that to which the receiver is
connected.
■Consult the dealer or an experienced radio/television technician for help.
You are cautioned that changes or modifications not expressly approved by the part responsible
for compliance could void your authority to operate the equipment.
Federal Communications Commission (FCC) Radiation Exposure Statement
This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment.
This equipment should be installed and operated with a minimum distance of 20 cm
between the radiator and your body.
CE Mark Warning
This is a Class B product. In a domestic environment, this product may cause radio
interference, in which case the user may be required to take adequate measures.
This transmitter must not be co-located or operated in conjunction with any other
antenna or transmitter.
Canadian Compliance Statement
This Class B digital apparatus meets all requirements of the Canadian Interference-
Causing Equipment Regulations.
Cet appareil numérique de la classe B respecte toutes les exigences du Règlement sur
le matériel brouilleur du Canada.
Adaptec, Inc. AWN-8060
Tested to Comply
With FCC Standards
FOR HOME OR OFFICE USE

1
In this Guide
Introduction 2
Installation Task List 3
Installing Your Wireless AP 6
Installing the Wireless Access Point Utility 8
Setting Your Wireless AP’s IP Address 12
Opening the Utility and Logging on 13
Connecting to the WLAN 14
Using the Wireless Access Point Utility 19
Changing the Set-up of Your WLAN 20
Troubleshooting 28
About Wireless Technology and LANs 30
Technical Specifications 32
Glossary 33

2
Introduction
Introduction
This User’s Guide provides detailed instructions for installing and
configuring your Wireless Access Point (Wireless AP) as part of a
Wireless Local Area Network (WLAN). See the
Installation Task List
on page 3 for an overview of the installation process.
This Guide also includes a basic overview of wireless and LAN
technology (see page 30) suitable for novice users. It assumes you
have a working knowledge of your computer and are familiar with
the Windows operating system.
Note: Your Wireless AP is only one element of your WLAN.
Installing this product alone will not create a wireless network.
See
About Wireless Technology and LANs on page 30 for
information on the minimum requirements for creating a WLAN.
Kit Contents
Your Adaptec Ultra Wireless Access Point kit includes:
■Adaptec Ultra Wireless Access Point (AWN-8060)
■Ethernet straight-through cable
■AC Power adapter
■Ultra Wireless Access Point CD, which contains documentation
and the Adaptec Wireless Access Point Utility
■Adaptec Ultra Wireless Access Point Quick Start Guide
System Requirements
To use your Wireless AP, you need a PC-compatible computer with:
■Pentium-class 90MHz (or faster) processor
■Microsoft Windows®98SE, Windows Me®, Windows 2000®, or
Windows XP®
■CD-ROM drive

3
Installation Task List
Installation Task List
To successfully install your Wireless AP, complete these tasks:
❏Follow the tips and suggestions provided in the next section,
Before You Begin.
❏Install the Wireless AP. See page 6.
❏Install the Wireless Access Point Utility. See page 8.
❏Set the IP address for your Wireless AP. See page 12.
❏Open and log on to the Utility. See page 13.
❏Connect to the WLAN. See page 14.
Installation takes approximately twenty minutes to complete.
Before You Begin
Review the features of your Wireless AP in This is Your Wireless
Access Point on page 4.
If you are unfamiliar with wireless technology or Local Area
Networks (LANs), read About Wireless Technology and LANs on
page 30 for a basic overview.
If you have any non-Adaptec brand Wireless products on your
WLAN, or if you have changed the default settings of your other
Adaptec Wireless products, you’ll find it easier to complete the
Installation Checklist if you have this information available before
you begin:
■Wireless Network ID (or SSID)
■Encryption settings
■Security authentication settings
■Preamble type
Caution: Install your Wireless AP as far away as possible from
potential sources of interference, such as microwave ovens,
2.4 GHz wireless telephones, baby monitors, and so on.
!

4
Installation Task List
This is Your Wireless Access Point
Top View
The top of your Wireless AP has four clearly labeled status
indicator lights (or LEDs). Once your Wireless AP is installed, these
LEDs display the status of the network and the condition of your
Wireless AP, as described:
LED On Off Blinking
DIAG Updating
firmware.
LAN LAN connection
is made.
Problem with
LAN connection.
Data is being
transmitted on
LAN.
Wireless Ready to receive
Wireless
connections.
Problem with
WLAN.
Data is being
transmitted on
WLAN.
Power Device is on. Device is off. -

5
Installation Task List
Side View
The DC-IN port connects your Wireless AP to a power source.
The LAN port connects your Wireless AP to your LAN.
The INIT button reboots your Wireless AP and resets it to its
factory default settings. (Press and hold the INIT button for 5
seconds to reset.)
DC-IN port INIT buttonLAN port
Side View

6
Installing Your Wireless AP
Installing Your Wireless AP
Before continuing, ensure that you have followed the tips and
suggestions provided in Before You Begin on page 3.
The next task on the Installation Task List (see page 3) is to install
your Wireless AP. This section helps you locate it in the best
possible position and guides you through the installation process.
Locating Your Wireless AP
For maximum performance, install your Wireless AP in the center
of your network, in a place that has a line of sight to all the devices
connecting to it. Keep it as far away as possible from potential
sources of interference, such as microwave ovens, 2.4 GHz wireless
telephones, baby monitors and other wireless devices.
Note: The higher you place your Wireless AP, the better the
signal coverage will be, especially if you have WLAN stations
upstairs from your Wireless AP.

7
Installing Your Wireless AP
Installing the Wireless AP
Your Wireless AP can fit into your WLAN in multiple ways. It can
be connected to a hub or switch on your network, a router on your
network, or a network adapter that’s installed in a computer on
your network.
To install the Wireless AP:
1Use the mounting screws to secure the Access Point in place, if
desired.
2Connect the Ethernet cable to the LAN port on the Access Point.
3Depending on your network configuration, connect the other
end of the Ethernet cable to the LAN port on:
■a hub or switch on your network.
■a router on your network.
■a network card installed in another computer on your
network.
4Connect the power adapter to the DC-IN port on the Access
Point (as shown in Step 2 on page 7), and plug it into a power
outlet.
5Raise the Access Point’s antennas.
Your Wireless AP is installed. See Installing the Wireless Access Point
Utility on page 8 to continue with your next Installation task.
Step 2:
Connect LAN.
Step 4:
Connect power.

8
Installing the Wireless Access Point Utility
Installing the Wireless
Access Point Utility
Before you continue, make sure that you have:
❏Followed the tips and suggestions provided in Before You Begin
on page 3.
❏Installed the Wireless AP. See page 6.
The next step on the Installation Task List (see page 3) is to install
the Adaptec Wireless Access Point Utility, a tool that helps you set
up and monitor your Wireless AP.
To install the Wireless Access Point Utility:
1Insert the Ultra Wireless Access Point CD into your CD-ROM
drive.
Note: Adaptec recommends that you install the Wireless
Access Point Utility and manage your Wireless AP on a
computer that is wired to your Wireless AP through a
network hub, switch, or router.
2In the Windows Start menu, click Run.
3Click Browse, and browse to your CD-ROM drive.
4Double-click setup.exe.
The InstallShield Wizard opens.

9
Installing the Wireless Access Point Utility
5Click Next.
6Type in your User Name and Company Name (optional), then
click Next.

10
Installing the Wireless Access Point Utility
7 The InstallShield Wizard chooses a default destination folder for
the software files. Click
Next to accept the default destination
(recommended), or click
Browse to select an alternate destination.
8You can choose where to store program icons in the Program
Folder. Accept the default folder name, type a new folder name,
or select one from the Existing Folders list. Click Next.

11
Installing the Wireless Access Point Utility
9Click Finish to complete the installation.
The Wireless Access Point Utility is installed. The Wireless Access
Point Utility icon appears on your desktop. See Setting Your
Wireless AP’s IP Address on page 12 to continue.

12
Setting Your Wireless AP’s IP Address
Setting Your Wireless AP’s
IP Address
Before you continue, make sure that you have:
❏Followed the tips and suggestions provided in Before You Begin
on page 3.
❏Installed the Wireless AP. See page 6.
❏Installed the Wireless Access Point Utility. See page 8.
The next step on the Installation Task List (see page 3) is to set the
IP address for your Wireless AP.
You must set the IP address for your Wireless AP if you have just
installed your Wireless AP, upgraded the firmware, or reset the
Wireless AP using its INIT button or the Reset button in the
Wireless Access Point Utility. You may also need to set the IP
address if you are having trouble connecting to the WLAN.
To set the IP address:
1Double-click the Wireless Access Point Utility icon on
your desktop (shown at right), or open the program
using the Windows Start menu.
The Utility
opens and begins to search for active Adaptec APs.
2Select your Wireless AP, then click Admin and select Set IP
Address.
3Click OK, then click Exit.
The IP address is set. See Opening the Utility and Logging on on
page 13 to continue.

13
Opening the Utility and Logging on
Opening the Utility and
Logging on
Before you continue, make sure that you have:
❏Followed the tips and suggestions provided in Before You Begin
on page 3.
❏Installed the Wireless AP. See page 6.
❏Installed the Wireless Access Point Utility. See page 8.
❏Set the IP address for your Wireless AP. See page 12.
The next step on the Installation Task List (see page 3) is to log on
to the Wireless Access Point Utility.
To log on to your Wireless AP:
1Double-click the Wireless Access Point Utility icon on your
desktop, or open the program using the Windows Start menu.
The Utility
opens and begins to search for active Adaptec Access
Points.
Note: If your Wireless AP is not listed in the Utility and you
are running the Utility on a Wireless network station, try
connecting your station to the same wired network as your
Wireless AP.
2Double-click the Wireless AP.
3In the User Name box, type admin.
4By default, no password is set. (See Changing the Administration
Password on page 26 for instructions on setting or changing the
Password.) However, if you set a password during a previous
session, enter it now.
5Click OK.
You are logged on to the Utility. See Connecting to the WLAN on
page 14 to continue.