ADATIS TouchEntry-XT User manual

TouchEntry®-XT
Installation Manual
Updated 02/2020 – Version 0.9
All manuals and user guides at all-guides.com

TouchEntry®-XT
1. Preparations
1.1 Content of delivery
•TouchEntry-XT terminal
•1 x all mounting bracket (depending on order option: surface-mounted or
flush-mounted)
•3 x RFID-cards: green, red, grey
•mounting kit
•1 x installation manual
1.2 Location
•Indoor and outdoor use (-20°C to +60°C temperature range)
•The terminal is suitable for outdoor use with high brightness. However, a
direct incidence of sunlight into the lenses (morning/evening sun) should be
avoided:
Recommended mounting height: 1.57 m, Center of the terminal
Installation 2
All manuals and user guides at all-guides.com

TouchEntry®-XT
1.3 Interfaces
All connections are located on the bottom of the terminal.
1.3.1 Ethernet, Power over Ethernet (PoE
An Ethernet connection can be established via the Ethernet
socket.
For power supply via Ethernet (PoE) a PoE-capable switch or
a PoE injector is required.
1.3.2 2Wire connection
If the terminal was ordered with the 2 ire option, the
wire ends of the 2 ire cable must be connected to the
2 ire socket.
For long distances, it is important to ensure a sufficient
wire cross-section.
For more information, refer to the installation guide and
manual of the 2 ire converter.
Installation 3
All manuals and user guides at all-guides.com

TouchEntry®-XT
1.3.3 Connections of the terminal
Bottom
•Ethernet, 10/100BaseT mit RJ45-Buchse
•2-wire socket (for option 2-wire kit)
•iegand output
•1 x Trigger input and 1 x Tamper contact or 2 x Tamper contacts
•1 x Relay, e.g. door opener
•1 x TTL output
Installation 4
All manuals and user guides at all-guides.com

TouchEntry®-XT
2 Wall mounting
The terminal is pre-assembled on delivery. Depending on the order option,
the terminal is delivered with a flush-mounted housing or a wall bracket for
surface mounting. In the following the flush mounting is shown. Surface
mounting can be done in the same way.
Use the appropriate wall bracket:
Flush-mounted: Surface-mounted:
1
Using the Allen key, turn the screws below the display (flush mount) or the
screw below the terminal (surface mount) counterclockwise until the
terminal can be pushed upwards and detached from the wall bracket:
Flush-mounted: Surface-mounted:
2
Installation 5
All manuals and user guides at all-guides.com

TouchEntry®-XT
3Only Flush-mounted:
For flush mounting, a wall cut-out
with the following dimensions must
be made:
288mm (h) x 136mm (w) x 36mm (d)
4 Use the flush housing to mark the
drill holes.
Make sure that the flush-mounted
housing is oriented correctly. hen
correctly mounted, the opening for
the cables is located in the lower
half.
Pull the Ethernet cable through the
cut-out on the back of the terminal.
Use the screws, seals and dowels
from the mounting kit to fix the
flush-mounted housing to the wall.
Installation 6
All manuals and user guides at all-guides.com

TouchEntry®-XT
5 Pull the seal over the Ethernet cable
and press the seal into the cut-out
in the back of the flush-mounted
housing.
6 Plug the Ethernet cable into the
Ethernet socket on the back of the
terminal.
7 Insert the terminal into the flush-
mounted housing and push the
terminal down until it snaps into
place.
Installation 7
All manuals and user guides at all-guides.com

TouchEntry®-XT
8Only Flush-mounted:
Check that the screws in the holes
of the flush-mounted housing have
been inserted correctly.
Tighten the screws (A and B) below
the display clockwise using the
Allen key.
9Only Surface-mounted:
Using the Allen key, tighten the
screw below the terminal
clockwise.
If correctly installed, the terminal must not be able to be moved.
3 Configuration
The manual for configuring and operating the XT door terminals can be
found on the Adatis website under Products - XT:
www.adatis.com
Installation 8
All manuals and user guides at all-guides.com