Adcraft HCD-5 User manual

SL
Chocofairy
04/2010
MANUALE ISTRUZIONI
Leggere attentamente queste istruzioni d’uso prima di utilizzare la macchina
MANUAL DE EMPLEO
Leer atentamente estas instrucciones de uso antes de utilizar la máquina
Lire attentivement ce mode d’emploi avant d’utiliser la machine
MODE D’EMPLOI
Diese Bedienungsanleitung ist vor dem ersten Gebrauch der Maschine
aufmerksam zu lesen
BETRIEBSANLEITUNG
Read these operating instructions carefully before using the machine
OPERATING INSTRUCTIONS

English version .......................................................... Pag.2 - EN
Deutsche version ....................................................... Pag.2 - DE
Version française........................................................ Pag.2 - FR
Versión española ....................................................... Pag.2 - ES
Versione Italiana .......................................................... Pag.2 - IT
Lingua originaria di riferimento per traduzione

7.14. Resetting the temperature sensor ......................19
7.15. Periodic maintenance..........................................19
8. SCRAPPING..............................................19
9. TROUBLESHOOTING...............................20
10. BASIC WIRING DIAGRAM........................21
04/2010

04/2010

Mod. 10 Liters
L=28 cm (11.02 inch)
P=41 cm (16.14 inch)
A=46,50 cm (18.31 inch)
L=28 cm (11.02 inch)
P=41 cm (16.14 inch)
A=58 cm (22.83 inch)
6,8 Kg
(14.96 Ib)
7,5 Kg
(16.5 Ib)
17 Boiler tank drainage cap
17
04/2010

3. SAFETY
3.1. General safety rules
Carefully read the whole instruction manual.
The connection to the electricity mains must comply with the current safety
Do not clean the machine with gasoline and/or solvents of any kind.
Do not site the machine near heating equipment (stoves or radiators).
standards in the user’s country.
The machine must be connected to an electric outlet that is:
The power cord must not be:
compatible with the plug provided with the machine;
of dimensions conforming to the data shown on the rating plate on the
side of the machine;
properly grounded;
connected to a system provided with a differential switch and circuit break-
connected to a system that has been certified according to the current
standards and regulations in the country of use.
er;
allowed to come into contact with any kind of liquid: danger of electric
shocks and/or fire;
crushed and/or brought into contact with sharp surfaces;
used to move the machine;
used if it shows any damage;
handled with damp or wet hands;
wound into a coil when the machine is on.
tampered with.
Repair work may be performed only by a Service Center authorized by the
Manufacturer and/or specialized, trained personnel.
ln case of fire, use carbon dioxide (CO2) extinguishers. Do not use water or
powder extinguishers.
In the event of improper use, all warranty rights will be forfeited
and the manufacturer will accept no liability for injury or dam-
age to persons and/or property.
The following are to be considered improper use:
- any use other than the intended use and/or with methods other than those
- any operation on the machine that is in contrast with the directions provided
- use of the machine after any components have been tampered with and/or
- use of the machine after it has undergone repair with components not au-
- outdoor installation of the machine.
The machine is shut down by turning off the on/off switch.
thorized by the manufacturer;
safety devices have been changed;
herein;
described herein;
3.2. Stop functions
04/2010

375 mm
(14.76 inch)
375 mm
(14.76 inch)
510 mm
(20.08 inch)
8,8 kg
(19.36 Ib)
375 mm
(14.76 inch)
375 mm
(14.76 inch)
600 mm
(23.62 inch)
9,5 kg
(20.9 Ib)
04/2010

Chocofairy
04/2010

remove the lid and pour the beverage prepared accor dl ng to the manu-
facturer’s lns tructlons lnto t he bowl;
04/2010

the machlnes wlth LCD offer the opportunlty to make a visual check to see
hen the product has reached the required temperature inside the bowl.
w
arnlng: during bowl and/or boller switch off the machine us-
To dispense hot chocolate proceed as follows;
place a cup beneath the tap;
use the lever on the tap (the product is dispensed when the lever is pressed
or pulled) until the required amount of product has been poured inside the
gradually release the tap lever so that it returns to the standby position (tap off).
cup;
ing the main swltch (LED off).
Warning: check to make sure that the water level never falla be-
low the minimum level, whlch is marked -MIN-; this will prevent
machine operations from being shut down.
- 115 V madel:
- 230 V model:
W
A level sensor wlll shut down machine operation as soon
as the water level falls below the minimum; to restore op-
eration, the boiler tank must be topped up. lf the machine
does not restart after the tank has been topped up, contact
a specialized technician.
The machine is not equipped with a level sensor and
therefore, as soon as the water level falls below the mini-
mum, the lntervention of a specialized technician will be
necessary to restore correct machine operation.
Warning: never operate the machine without water in the boiler
as this would damage the heating element. a temperature sen-
sor will in any case cut out power to the heating element if there
is no water in the boiler. To restore the machine to normal op-
lf the product is especially thick, it is advisable to keep the rod
pulled out at the maximum position; any clogging in the dis-
pensino line may be removed by sliding the rod back and forth
while keeping the machine, as shown in the Fig. 12.
Warning: never touch the bowl or lid while the machine is oper-
ating, since they are very hot, Always use the knob when mov-
ing the bowl lid.
eration press the pushbutton underneath the base.
Warning: power will still be supplied to the machine, even dur-
ing the shutdown.
Warning: for correct machine operation, only use demineralized
water in the boiler tank.
SL320001846 Ed.03 - 06/2008
6.2 Dispensing the product
Warning: the product dispensed from the machine has a very
high temperature; risk of scalding.
It is advisable to keep the rod in the maximum dispensing posi-
tion to help the product to flow at the required rate.
- 9_EN -
04/2010

04/2010

04/2010

unhook the bowl hook-on handles, as illustrated in the figure, to free the bowl
slide the mixing auger upwards with one hand, taking care to grip it by the
place the bowl on a flat surface and using both hands, romove the gasket by
sliding it upwards in the direstion shown by the arrow.
Removing the tap is prohibited if the bowl contains the product
or any other liquid.
To remove the tap, proceed as follows:
move the rod to the maximum dispensing position;
rotation pin;
from the machine body;
release the bowl from the machine body, using two fingers to prise it away
from the fixed steel part of the mixer auger (A) and the others to grip the
outer edge of the bowl (B): Gradually pull the bowl harder until it comes away
from its seating;
slide the bowl upwards using both hands;
7.4. Rem oving the tap
SL320001846 Ed.03 - 06/2008
- 1 2 E N
04/2010

press the button (A) securing the tap to the machine and then remove the
tap (B) with both hands, as illustrated in the figure;
7.5. Cleaning the pan
lt is necessary to remove all parts fitted to the pan.
Remove any product left in the bowl, see paragraph 7.2;
remove the bowl from the machine, see paragreph 7.3;
remove the tap from the machine, see paragraph 7.4;
clean the entire surface of the pan using a damp cloth and/or a non-abrasive
sponge;
clean the channel connecting the bowl and the tap, using a cleaning brush,
as illustrated in the figure;
refit the tap;
pour a little water inside the pan;
use the tap to drain out all of the water from the pan so as to eliminate any
small product residues inside the dispensing channel.
- 1 3_ E N -
SL320001846 Ed.03 - 06/2008
04/2010

04/2010

04/2010

Fig. 37 shows a bpwl which is not correctly assembled;here the bowl does NOT insert the mixer into its seating following the steps descrlbed in paragr
7.3 in reverse order.
perfectly adhere to the machine edge.
Fix the bowl to the machine body using the relevant hook-on handles, as
To reassemble the tap, carry out in reverse all of the disassembly steps
trated previously (Fig. 32 to Fig. 27).
illustrated in the figure;
insert the mixer auger into its seating;
- 16_EN -
aph
7.8.2. Assembling the tap
illus-
To fi t the lever (F) push the rod (D) from the inside until the guides protrude;
SL320001846 Ed.03 - 06/2008
04/2010

To fl t the tap correctly b ack in place proceed as follows;
Note: t he tray needs to be emptied out a nd cleaned every time
that the red float fitted to the grid rises; thi s is to stop llquid
from leaking out.
lift the tray with grid and pull it outwar ds t o rem ove it fro m lts seating;
wash the tray and grid separately with lukewarm water.;
dry all of the components;
reposition the grid on top of the tray ;
fit the tray back in place and press down to secure it to the machine.
Carry out the following steps:
prepare the sanitising solution
(see paragraph 7.7);
fill the bowl with the s anitising solution;
leave the solution to act for about 30 minutes;
empty out the sanitising solution from the bowl;
then rinse out the bowl and inside surfaces thoroughly to eliminate all resi-
dues of sanitizing solution.
SL320001846 Ed.03 - 06/2008 -17 EN -
Rem o ve the b owl lid from the ma c hine;
Warnin g! th e th er m o s t a t m u st b es e t t o - OFF-.
in sanitising product.
rinse thoroughly using clean water.
clean the surface using a damp cloth and/or a non-abrasive spong e soaked
T he drip tray should be emptied and cleaned dally.
hold d o wn t he bu tt on , m akin g sure that the rod is c om p le tely e xtra ct ed;
introduce the tap into the seat provided and push until the pushbutton re-
turns to its initial p osition.
7.8.3 Fitting the tap
7.10. Cleaning the drip tray
7.9. Internal saniti zation
7.11. Cleaning the bowl lid
04/2010

04/2010

The machine must be periodically checked (at least once a
year) by a specialised technician. This periodic check serves
to ensure that all the components installed and the machine
itself are maintained at a high level of safety.
Any worn components must be replaced by an original spare part.
It is forbidden to use the machine when even only one of its
components is faulty or worn. Users are forbidden to perform
periodic maintenance.
8. S CRAPPING
7. 15.Periodic maintenance
Electrical and electronic equipment needs to be disposed of
according to the European Directive 2002/96/CE and in com.
pllance with the standards and regulations in force tor the
country in which the machine is used.
Such equipment may not be disposed of as normal municipalsolid
waste but must rather be separately collected to optimise recovery
and recycling of the materials used to manufacture them.
reminder of separate collection obligations.
will contribute to safeguarding the environment.
All products are marked with the crossed out wheeled bin symbol as a
Correct observance of all of the provisionsfor the disposal of end-of-life pr ducts
- 19_EN -
Fig. 48
Fig. 49
7.14. Resetting the temperature sensor
04/2010