AddPac AP-GS1001 User manual

www.addpac.com
GSM Gateway
High Performance GSM Gateway Solution
WEB Setup Guide
AP-GS1001 / AP-GS1002 / AP-GS1004

www.addpac.com 2
1. WEB Connection
2. Network Setup
3. Language
4. GSM Setup
5. VoIP Setup
6. Callback Service
7. LCR
8. SMS
9. Advanced Service
10.Monitoring
Contents

www.addpac.com 3
WEB Connection
1. Web Connection via Console Port
2. Web Connection via LAN 1 Port

www.addpac.com 4
WEB Connection
Serial port
Console
Port
Baud rate 9600
No parity
1 stop bit
No flow control
login ID/Password : root/router
GSM> enable => Enter the enable mode
GSM# configure terminal => Enter the configuration mode
GSM(config)# interface FastEthernet 0/0
GSM(config-if)# ip address <IP Address> <Subnet Mask> => Ex) ip address 172.17.109.1 255.255.0.0
GSM(config-if)# exit
GSM(config)# ip route 0.0.0.0 0.0.0.0 <Defualt Gateway> => Ex) ip route 0.0.0.0 0.0.0.0 172.17.1.1
GSM(config)# write => saving
Proceed with write? [confirm]y
1. Connect to GSM G/W via console port to enter IP
address in order to set Interface 0/0
2. Input IP address of interface 0/0 using below command
3. Connect to the IP address via web after saving
1. Web Connection via Console Port (AP-GS1002, AP-GS1004)
* Following information is not applicable to AP-GS1001

www.addpac.com 5
WEB Connection
Cross Cable
LAN 1
LAN 1 Default IP
IP Address : 192.168.10.1
Subnet mask : 255.255.255.0
1. It is the way to connect to GSM G/W via LAN 1 port
2. The factory default of LAN 1 port
- IP Address : 192.168.10.1
- Subnet mask : 255.255.255.0
3. After set PC with same IP address subnet, connect to GSM G/W
- Connect PC to GSM G/W using Cross UTP-Cable. You may use Ethernet switch with normal UTP-cable
- Enter IP address 192.168.10.1 on your web browser
2. Connection Web via LAN 1 Port (AP-GS1001, AP-GS1002)
•Following information is not applicable to AP-GS1004

www.addpac.com 6
WEB Connection
1. The screen of Web connection
•The Shown log-in screen is connection to Web page.
Please enter the below log-in information
ID : root
Password : router

www.addpac.com 7
Network Setup
1. WAN Setup -1
①
Click
①WAN Setup
-Hostname : Enter the device name of GSM G/W
-Static IP
-PPPoE(ADSL)
-DHCP
* Please make sure to press the apply button for saving

www.addpac.com 8
Network Setup (Tunneling Setup)
1. WAN Setup -2
①
①PPTP ( Point-Point Tunneling Setup)
-PAP ( PPP Authentication Protocol) , CHAP (Challenge Handshake Authentication Protocol)
- Source : Setup the interface to connect with PPTP server.
- Destination : Enter the Tunnel End Point Address regard of Source.
- Service : Decide whether to apply Ethernet interface regard of Voice and Data communication.
* Please make sure to press the apply button for saving
Click

www.addpac.com 9
Network Setup (LAN Setup)
2. LAN Setup
LAN Setup
- IP Share (IP Connect)
- Static : 1. Setup LAN 1 Port Static IP
2. Setup DHCP Server
* Please make sure to press the apply button for saving

www.addpac.com 10
GSM Setup
1. GSM Dial Plan / Prefix
2. GSM Extension
3. FXS Extension
4. Hotline

www.addpac.com 11
GSM Setup > Dial Plan
1. GSM Dial Plan / Prefix -1
②
①
Dial Plan / Prefix : Setting for making outgoing call to GSM Networks using FXS or VoIP
①Plan Table : Outgoing call to GSM network can be made with number conversion
②Prefix Table : it is for outgoing call to GSM Networks. Both 1 Stage and 2 Stage are available
1 Stage : Making call after hearing the first dial-tone. Setting Prefix field is required
2 Stage : Making call after the second dial-tone. Setting 2nd Prefix field is required.
In case of 2nd stage using, the Prefix can be used a number for hearing the Second dial-tone

www.addpac.com 12
GSM Setup > Dial Plan
①Digit to Insert : inserted Number
Number of Digit to Delete : Number of digit to delete
Digit Pattern : Number to apply for conversion
②
①
1. GSM Dial Plan / Prefix - 2 (Example)
It is required to set the same number
on Plan Index of Prefix Table and
Index number of Plan Table
②Prefix , 2nd Prefix : Setting method of 1 stage and
2 stage
(ex : Prefix –T 1 stage method –Forward call
immediately
Prefix –9, 2nd Prefix –T Whe press 9, it is the
method to press dial after hearing 2nd dial-tone
PlanIndex : Set index applied for Plan Table
SlotPort : Set GSM port

www.addpac.com 13
GSM Setup > GSM Extension
GSM Extension Configuration
: Register GSM SIM Number
: Other party’s number can be registered with Call back Service
- Index : Sequential number for each extension.
Existed number makes configuration modified
- Port : Select port to set up
- Numbers : Register SIM number or mobile phone number
to use callback service
2. GSM Extension -1
GSM Extension with Translation
: Use to convert mobile phone number for callback service
- Destination Pattern : Enter mobile phone number to convert
- Digits to Insert : Insert number to make calling number
- Number of Digits to Delete : Delete number to make calling
number
ex) Destination Pattern : 025683848
Digits to Insert : 82
Number of Digits to Delete : 2
------------------------------------
Result : 825683848

www.addpac.com 14
GSM Setup > FXS Extension
3. FXS Extension -1
①The each port information of GSM Gateway
②FXS Extension : Set the number of phone on FXS port
- Index : Enter number in order. Please make sure not to be duplicated
- Port : Select FXS port to be set
- Numbers : Enter FXS number
- Preference : Set priority for each number.
If there is the same number at two ports, a port is selected by this priority
- Hunt Stop : It is a function of forward a call to other party in case of unavailable receiving call.
Activation of this function is recommended
②
①

www.addpac.com 15
GSM Setup > FXS Extension
3. FXS Extension -2 (Example)
②
①
①Set the number to be used for FXS 0/2 port (ex. 2000)
②Set the number to be used for FXS 0/3 port (ex. 3000)
•Setting number on each FXS port is required, so that Dial-tone can be heard on phone.

www.addpac.com 16
GSM Setup > FXS Extension
※Digit Structure※
- 9T : All number started with 9 as the first digit
- 4.. : Three digit number started with 4 as the first digit
- [2-9]T : All number started with 2 to 9 as the first digit
- 00[127]T : All number started with 001, 002, 007 as the first digit
** T: Accept all number entered within Inter Digit Time (Default IDT : 3sec)
** Dot(.) : One dot(.) means one digit
** [ ] : The range of number
※Rule tranfer※
- Digit pattern : 025683848 / Digits to insert : 82 / Number of digits to delete : 1 8225683848
- Digit pattern : 00[127]T / Digits to insert : 123 / Number of digits to delete : 2 123[127]T
- Digit pattern : [2-9]4... / Digits to insert : 823848 / Number of digits to delete : 3 823848..
AddPac Digit Structure

www.addpac.com 17
Direct Incoming call
4. GSM Setup > Hot Line -1
①Hot Line Configuration : Connect incoming and outgoing call directly
- Port : It means GSM and FXS port
- Hot Line Number : Forward call to entered number
It connects to the number of GSM port in case of receiving call (Direct Incoming call)
- Digit Input Timeout : Time to make call to the Hot Line Number when user doesn’t any action after off-hook
①

www.addpac.com 18
VoIP Setup
1. VoIP Setup
- Server SIP
- Server H.323
2. DTMF/CODEC
3. VoIP Dial Plan
4. Static Route

www.addpac.com 19
VoIP Setup (Protocol)
1. Protocol ( SIP or H.323 )
①Protocol
- Setup SIP or H.323 Protocol.

www.addpac.com 20
VoIP Setup
1. SIP Setup