Huawei eSpace EGW1500E User manual

eSpace EGW1500E Enterprise Gateway
V100R001C06
Quick Start
Issue 03
Date 2011-12-20
HUAWEI TECHNOLOGIES CO., LTD.

Issue 03 (2011-12-20) Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd.
i
Copyright © Huawei Technologies Co., Ltd. 2011. All rights reserved.
No part of this document may be reproduced or transmitted in any form or by any means without prior
written consent of Huawei Technologies Co., Ltd.
Trademarks and Permissions
and other Huawei trademarks are trademarks of Huawei Technologies Co., Ltd.
All other trademarks and trade names mentioned in this document are the property of their respective
holders.
Notice
The purchased products, services and features are stipulated by the contract made between Huawei and
the customer. All or part of the products, services and features described in this document may not be
within the purchase scope or the usage scope. Unless otherwise specified in the contract, all statements,
information, and recommendations in this document are provided "AS IS" without warranties, guarantees or
representations of any kind, either express or implied.
The information in this document is subject to change without notice. Every effort has been made in the
preparation of this document to ensure accuracy of the contents, but all statements, information, and
recommendations in this document do not constitute the warranty of any kind, express or implied.
Huawei Technologies Co., Ltd.
Address: Huawei Industrial Base
Bantian, Longgang
Shenzhen 518129
People's Republic of China
Website: http://www.huawei.com
Email: [email protected]

eSpace EGW1500E Enterprise Gateway
Quick Start Contents
Issue 03 (2011-12-20) Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd.
ii
Contents
1 Planning and Preparation............................................................................................................1
1.1 Safety Precautions............................................................................................................................................ 1
1.2 Checking the Installation Environment ............................................................................................................ 2
1.3 Unpacking Check............................................................................................................................................. 2
1.4 Customer Requirement Analysis and Network Planning ................................................................................. 3
2 Hardware Installation ..................................................................................................................5
2.1 Preparing Installation Tools.............................................................................................................................. 5
2.2 Installing EGW1500E ...................................................................................................................................... 5
2.3 Connecting Cables ........................................................................................................................................... 6
2.4 Powering On the EGW1500E .......................................................................................................................... 7
3 Product Function Configuration ................................................................................................8
3.1 Logging In to the Web Management System ................................................................................................... 8
3.2 Configuring Internet Access............................................................................................................................. 9
3.3 Configuring Voice Functions.......................................................................................................................... 12
4 FAQs ..............................................................................................................................................20
5 Qualification Card ......................................................................................................................22
6 Declaration on Hazardous Substances in Electronic Information Products ...................23

eSpace EGW1500E Enterprise Gateway
Quick Start 1 Planning and Preparation
Issue 03 (2011-12-20) Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd.
1
1 Planning and Preparation
1.1 Safety Precautions
For more information about safety precautions, see the eSpace EGW1500E Enterprise
Gateway Product Documentation.
Basic Requirements
zThe installation instructions provided should be followed.
zIn the event of a fault, contact the maintenance personnel. Do not open the device.
zAny company or person cannot change the design of the structure or security without
permission.
zThis device must be used in compliance with the legal and regulatory requirements of the
country in which it is being used. Please respect the legal rights of others when using this
device.
Usage Notice
zKeep the power plug clean and dry to avoid risk of electric shock and other potential
risk.
zUse the power supply adapter provided with this product.
zKeep your hands dry when plugging in or out the device cable.
zWhen the device is not in use, the power should be turned off and the mains power cable
should be disconnected from the mains supply.
zKeep water and other liquids away from the device. In the event of liquid coming into
contact with the device, disconnect from the power immediately. Remove all cables,
including network connections and power cables and contact your maintenance
personnel.
zIn the event of unusual behavior, such as smoke emitting from the device, unusual noises
or smells, disconnect from the mains power supply immediately, remove all the cables
connected to the device and contact an authorized maintenance personnel.
Cleaning Notice
zBefore cleaning, the device should be shut down and disconnected from the mains power
supply, removing all power and network cables.
zClean using a soft, dry cloth. Do not use liquid or aerosol cleaners on this device.

eSpace EGW1500E Enterprise Gateway
Quick Start 1 Planning and Preparation
Issue 03 (2011-12-20) Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd.
2
1.2 Checking the Installation Environment
Before installation, check the installation environment.
Table 1-1 lists the major check items in the installation environment.
Table 1-1 Major check items in the installation environment
Item Requirement
Damppr
oof
Working humidity: 5%–95% relative humidity (RH), no condensing. The
dehumidifier devices such as air conditioners with the dehumidifier function and
special dehumidifiers must be installed in the equipment room where the
relative humidity is higher than 95%. Water seepage, dripping, and dew
producing are forbidden in the room.
Dustpro
of
If the equipment room is close to a dust source, such as a coal mine, a country
road or a farmland, install aluminum alloy windows and fireproofing doors.
Lightpr
oof
Place the device in an environment without direct and strong sunlight.
Interven
tion-pro
of
Prevent the device from other RF devices within 50 meters. Place the device at
the center of the working area by considering the WLAN coverage range. Install
the antennas vertically to get the best WLAN performance.
AC
power
In the equipment room, a stable AC power supply that meets the power
requirements of the equipment must be available.
Heat
dissipati
on
Place the device in an environment with good ventilation and without heat
sources. Leave more than 10 cm space for heat dissipation at the top and all four
sides of the device.
1.3 Unpacking Check
You need to check the received equipment according to the packing list and check whether all
the materials (such as hosts, cables, and CD-ROMs) are complete and undamaged.If any
material is damaged or lost, contact the local merchant.
Table 1-2 Packing list
Item Quantity Remarks
eSpace EGW1500E including
antennas
1 -
Power supply adapter 1 -
Straight-through network cable 1 A straight-through network cable is 2
meters long.
Swell fixtures 2 Swell fixtures are used to install the
EGW1500E on the wall.

eSpace EGW1500E Enterprise Gateway
Quick Start 1 Planning and Preparation
Issue 03 (2011-12-20) Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd.
3
Item Quantity Remarks
Document and CD-ROM 1 Product document and open source code
notice.
eSpace EGW1500E Enterprise
Gateway Quick Start
1 Containing the product certificate and the
Declaration on Hazardous Substances in
Electronic Information Products.
1.4 Customer Requirement Analysis and Network
Planning
This topic describes the customer requirements that you need to obtain and the typical
networking.
Collecting Customer Requirements
You need to obtain customer requirements as listed in Table 1-3 before installing and
configuring the device.
Table 1-3 Customer requirements
Item Description
Internet access Determine the access mode (ADSL or WAN) and whether the
customer requires 3G network backup.
Number of POTS users Determine the number of POTS phones.
Number of SIP users Determine the number of IP phones and soft terminals.
Internal number Learn about the customer's requirements on internal numbers.
FXO ports The EGW1500E connects to the PSTN network by means of
FXO ports. It supports FXO-based switchboard and dedicated
line functions.
... ...
Network Planning
Figure 1-1 shows the typical networking of the EGW1500E.

eSpace EGW1500E Enterprise Gateway
Quick Start 1 Planning and Preparation
Issue 03 (2011-12-20) Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd.
4
Figure 1-1 Typical networking

eSpace EGW1500E Enterprise Gateway
Quick Start 2 Hardware Installation
Issue 03 (2011-12-20) Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd.
5
2 Hardware Installation
2.1 Preparing Installation Tools
This topic describes the tools for installing the EGW1500E on the wall. If you want to install
the EGW1500E on a horizontal surface, place it on the surface.
Table 2-1 Installation tools
Phillips screwdriver
Claw hammer
Hammer drill
Level ruler
2.2 Installing EGW1500E
Install an EGW1500E on a horizontal surface or on the wall.
Installing EGW1500E on a horizontal surface is easy. You only need to place it on the surface
and leave 10 cm space around for heat dissipation.
To install an EGW1500E on the wall, fix the swell fixtures and ensure that 5 mm of the swell
fixtures is exposed for mounting the EGW1500E, as shown in Figure 2-1.

eSpace EGW1500E Enterprise Gateway
Quick Start 2 Hardware Installation
Issue 03 (2011-12-20) Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd.
6
Figure 2-1 Mounting an EGW1500E on the wall
2.3 Connecting Cables
This topic describes how to connect cables for the EGW1500E.
Select a cable connection mode based on the site requirements. Figure 2-2 and Figure 2-3
show the cable connection modes.
Figure 2-2 ADSL access
The ADSL splitter separates voice and data signals. You can connect the splitter to ADSL and FXO ports
of the EGW1500E or connect ADSL ports on user devices to the ADSL port of the EGW1500E.

eSpace EGW1500E Enterprise Gateway
Quick Start 2 Hardware Installation
Issue 03 (2011-12-20) Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd.
7
Figure 2-3 Broadband access
zThe EGW1500E provides eight LAN interfaces, which can connect to terminals such as computers
and IP phones. To use more than eight LAN interfaces, connect the EGW1500E to an Ethernet
switch or hub.
zThe EGW1500E provides four POTS interfaces (PHONE1 to PHONE4), which can connect to
common phones or fax machines. To use more than four POTS interfaces, connect the EGW1500E
to an IAD.
2.4 Powering On the EGW1500E
After cables are connected, press the power button to power on the EGW1500E. View the
power supply indicators and verify that the EGW1500E is working properly. Before pressing
the power button, ensure that all cables are connected correctly to the ports.
Figure 2-4 shows the location of the power button. If the POWER indicator is on, the
EGW1500E works properly.
Figure 2-4 Power button

eSpace EGW1500E Enterprise Gateway
Quick Start 3 Product Function Configuration
Issue 03 (2011-12-20) Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd.
8
3 Product Function Configuration
3.1 Logging In to the Web Management System
The web management system allows users to set parameters, detect faults, and upgrade
devices.
Procedure
Step 1 Set the mode in which IP addresses are obtained to Obtain an IP address automatically.
Step 2 Log in to the EGW1500E using Internet Explorer 6.0 or later. The default URL is
http://192.168.1.1.
The default IP address of the EGW1500E, login user name, and password can be obtained from the label
at the bottom of the EGW1500E.
Step 3 Enter the user name admin and default password Admin@123, and click Log In. The page is
shown in Figure 3-1.

eSpace EGW1500E Enterprise Gateway
Quick Start 3 Product Function Configuration
Issue 03 (2011-12-20) Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd.
9
Figure 3-1 Logging in to the web management system
----End
3.2 Configuring Internet Access
This document describes how to configure the basic Internet access functions, as shown in
Table 3-1. For the 3G, MAN, VLAN, static route, QoS, network security, and other
network-related functions, see the eSpace EGW1500E Enterprise Gateway Product
Documentation.
Table 3-1 Internet access function
Description
Through ADSL
Through the
WAN port
Select one out of the two.
NOTE
zThe EGW1500E connects to the IP network using an ADSL port, a WAN port,
or a 3G data card. The 3G data card is the backup of an ADSL or WAN port.
When the ADSL or WAN port is unavailable, the EGW1500E can connect to
the IP network through the 3G data card, ensuring nonstop service transmission.
zFor details about 3G configurations, see the eSpace EGW1500E Enterprise
Gateway Product Documentation.
WLAN function Enable the WLAN function and set a password to access the WLAN.

eSpace EGW1500E Enterprise Gateway
Quick Start 3 Product Function Configuration
Issue 03 (2011-12-20) Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd.
10
Procedure
Step 1 On the web management page, choose Quick Setup from the navigation tree.
Figure 3-2 Quick Setup
Step 2 Complete the configuration according to Figure 3-3, Table 3-2, Figure 3-5, Table 3-4, Figure
3-4, and Table 3-3.
Figure 3-3 Setting ADSL parameters
Table 3-2 ADSL parameters
Parameter Description
VPI Virtual path identifier (VPI), which is obtained from the network carrier.
VCI Virtual channel identifier (VCI), which is obtained from the network
carrier.
PPPoE User
Name
User name to access the network, which is obtained from the network
carrier.
PPPoE
Password
Password to access the network, which is obtained from the network
carrier.

eSpace EGW1500E Enterprise Gateway
Quick Start 3 Product Function Configuration
Issue 03 (2011-12-20) Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd.
11
Figure 3-4 Setting WAN parameters
Table 3-3 WAN parameters
Parameter Description
PPPoE Indicates that Point-to-Point Protocol over Ethernet (PPPoE) is used.
zPPPoE User Name: user name to access the network, which is
obtained from the network carrier.
zPPPoE Password: password to access the network, which is obtained
from the network carrier.
Static IP Indicates that the static IP address of the EGW1500E is used. The
setting must be the same as that on the Broadband Remote Access
Server (BRAS) of the network carrier.
DHCP As a DHCP client, the EGW1500E obtains the IP address from the
DHCP server. The IP address must be the same as that on the BRAS of
the network carrier.

eSpace EGW1500E Enterprise Gateway
Quick Start 3 Product Function Configuration
Issue 03 (2011-12-20) Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd.
12
Figure 3-5 Setting WLAN parameters
Table 3-4 WLAN parameters
Parameter Description
WLAN Indicates whether to enable the WLAN function. This function is
enabled by default.
SSID Indicates the service set identifier (SSID), which identifies a WLAN.
WPA-PSK/WP
A2–PSK Key
Indicates the password to access the WLAN. The password is encrypted
through Wi-Fi protected access II-pre-shared key (WPA2-PSK) and
WPA-PSK. The EGW1500E uses the PSK to encrypt all
communication, which prevents unauthorized listening and access. The
default password is the MAC address of the EGW1500E, which can be
viewed from the bottom label of the device.
----End
Verification
To verify that the ADSL/WAN connection is set up, proceed as follows:
Step 1 Choose System > Network. The Network page is displayed.
Step 2 Check the value of Status.
If the value of Status is Connected, the ADSL/WAN connection is set up. If the value is not
Connected, verify that the configuration is correct.
----End
3.3 Configuring Voice Functions
This topic describes how to configure internal and external numbers to implement voice
communication. For the configuration of voice services, FXO-based switchboard and
dedicated line functions, fax, and power failure survival function, see the eSpace EGW1500E
Enterprise Gateway Product Documentation.

eSpace EGW1500E Enterprise Gateway
Quick Start 3 Product Function Configuration
Issue 03 (2011-12-20) Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd.
13
Before the configuration, plan user numbers and configure the SIP server based on the customer
requirements obtained in 1.4 Customer Requirement Analysis and Network Planning.
User Number Planning (IMS)
Table 3-5 describes the number plan for the phones connected to the IMS network.
Obtain the external number, registration type, SIP trunk ID, SIP trunk user name, and IMS domain name
from the network carrier. The external number corresponds to the SIP trunk ID. If the SIP trunk ID
starts with a plus (+), change the plus to 00 when configuring the external number.
Table 3-5 Number plan for the phones connected to the IMS network
User Internal
No.
External
No.
Registr
ation
Group
Register
Type
Sip
Trunk
ID
Sip
Trunk
Name
IMS
Domai
n
User1 6001 00865718
7654321
User2 6002 00865718
7654322
User3 6003 00865718
7654323
... ... ...
0 Group +86571
8765432
1
+865718
7654321
@abc.de
f.com
abc.def.c
om
User Number Planning (NGN)
Table 3-6 describes the number plan for the phones connected to the NGN network.
Obtain the external number, registration type, SIP trunk ID, and SIP trunk user name from the network
carrier. The value of RegisterType is usually Single for the NGN network. The external number
corresponds to the SIP trunk ID.
Table 3-6 Number plan for the phones connected to the NGN network
User Internal
No
External
No
Registr
ation
Group
Register
Type
Sip
Trunk
ID
Sip
Trunk
Name
IMS
Domai
n
User1 6001 00865718
7654321
0 Single 0571876
54321
0571876
54321
N/A
User2 6002 00865718
7654322
1 Single 0571876
54322
0571876
54321
N/A
User3 6003 00865718
7654323
2 Single 0571876
54323
0571876
54321
N/A
... ... ... ... ... ... ... ...

eSpace EGW1500E Enterprise Gateway
Quick Start 3 Product Function Configuration
Issue 03 (2011-12-20) Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd.
14
SIP Server Planning
Table 3-7 Configuration reference
SIPServer Type Address Type Description
The value can be NGN or
IMS, which is determined
by the network carrier.
IP/Domain IP address or DNS domain name of the
SIP server. The value is provided by the
network carrier. For example, 191.1.1.1.
Configure the Session Initiation Protocol (SIP) server.
Step 1 On the web management page, choose Voice > SIP Server from the navigation tree.
Step 2 Click .
Figure 3-6 SIP Server tab page
Step 3 Perform configurations according to the following tables. Click to save the
settings.
Table 3-8 Parameter description (1)
Parameter Description
Working Mode zMaster: active server. The server that is added first is the active server.
zSlave: standby server.
Recovery Whether to enable the failback function. When the active server fails,
resources and services will be automatically switched to the standby
server. If this function is enabled, resources and services will be
automatically switched back to the original active server after the
original active server has been recovered.
OptionInterval Interval for sending the option messages to the active server. The value
ranges from 10 to 900, in seconds. The default value 60 is recommended.
NOTE
The option messages are sent to active server only, and therefore this parameter is
valid only for the active server.

eSpace EGW1500E Enterprise Gateway
Quick Start 3 Product Function Configuration
Issue 03 (2011-12-20) Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd.
15
Parameter Description
Address Type Address type. The options are IP and Domain.
IP/Domain IP address or DNS domain name of the SIP server. The value is provided
by the network carrier.
DNS Type Mode for the DNS server to parse the IP address. This parameter is valid
when Address Type is set to Domain.
zSRV: Two IP addresses are parsed from one the domain name parsing.
One IP address functions as the IP address of the active server, and the
other functions as the IP address of the standby server.
NOTE
If you set DNS Type to SRV, you do not need to configure the slave SIP server.
zHOST: One domain name corresponds to one IP address. To perform
switchover between the active and standby servers, two SIP servers
need to be configured.
Server Type SIP network type,The value is provided by the network carrier.
Port Port number of the SIP server. The value is provided by the network
carrier. The default value 5060 is recommended.
Expiration
Time
Timeout duration for the registration group to register with the SIP
server. The value ranges from 0 to 14400, in seconds. The default value
360 is recommended.
----End
Configure a registration group
Step 1 On the web management page, choose Voice > SIP Server from the navigation tree.
Step 2 Click .
Figure 3-7 SIP Group tab page
Step 3 Perform configurations according to Table 3-9. Click to save the settings.

eSpace EGW1500E Enterprise Gateway
Quick Start 3 Product Function Configuration
Issue 03 (2011-12-20) Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd.
16
Table 3-9 Parameter description (2)
Parameter Description
RegisterType Registration type. This parameter is specified by the peer SIP server.
zSingle: Only one user can exist in the registration group. The value
of RegisterType is Single for the NGN network.
zGroup: Multiple users can exist in the registration group.
zWildcard: Wildcard registration group. This registration group
registers with the IMS or NGN based on certain wildcard rules,
which are provided by the network carrier.
Authentication Authentication mode when a registration group registers with the IMS
or NGN. The value is provided by the network carrier.
Password The value is provided by the network carrier.
Sip Trunk ID The value is provided by the network carrier.
Sip Trunk Name The value is provided by the network carrier.
IMS Domain The value is provided by the network carrier.
Expiration Time Indicates the time when the SIP group expires. The value is negotiated
by the EGW1500E and the SIP server. The EGW1500E must be
registered with the SIP server at least once within the expiration time to
ensure that the SIP server can exchange information with the
EGW1500E.
----End
Add SIP users
Step 1 On the web management page, choose Voice > Phone Allocation from the navigation tree.
Step 2 Click .
Figure 3-8 Adding SIP users
Step 3 Perform configurations according to Table 3-10. Click to save the settings.

eSpace EGW1500E Enterprise Gateway
Quick Start 3 Product Function Configuration
Issue 03 (2011-12-20) Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd.
17
Table 3-10 Parameter description (3)
Parameter Description
Internal No The internal number is used for the calls between intra-office
subscribers.1-30 digit number, which can be user-defined. It cannot
conflict with any service prefixes, emergency numbers, outer-office
numbers, or other intra-office numbers.
User Name A string of 1-64 characters, which can be user-defined. For example, Jack.
Authenticatio
n
Authentication mode used when a SIP user registers with the EGW1500E.
The value must be the same as that set on the SIP terminal.
Password Authentication password used when a SIP user registers with the
EGW1500E. The value must be the same as that set on the SIP terminal.
Registration
Group
Registration group used when a SIP user registers with the IMS or NGN.
NOTE
If the required registration group does not exist, choose Voice > SIP Server, and
click the SIP Group tab to add it.
External No External number of the user, which is used for outgoing and incoming
calls. It is provided by the carrier. This parameter is valid after you set the
Registration Group parameter. The external number cannot conflict with
any service prefixes, emergency numbers, outer-office numbers, or other
intra-office numbers.
NOTE
Registration Group bound to External No must correspond to Sip Trunk ID. If
Sip Trunk ID starts with +, you need to change + to 00 when you configure
External No.
Digitmap A dialing rule, which determines whether the range and length of the
dialed number comply with the dialing rule. This parameter is valid after
you set the Registration Group parameter. The EGW1500E allows users
to dial numbers that are defined in the digitmap to make calls quickly. If
the dialed number length is the same as that defined in the digitmap, the
EGW1500E stops collecting digits and initiates the call, which reduces the
connection duration. Use the default settings. To customize the settings,
see the eSpace EGW1500E Enterprise Gateway Product Documentation.
User State User status.
IP Address IP address of the IP phone on the LAN.
----End
Add POTS users
Step 1 On the web management page, choose Voice > Phone Allocation from the navigation tree.
Click the POTS User tab page.
Step 2 Click .