ADEMCO 5110XM User manual

5110XM
N8026 4/96
Installation Instructions • Installation Instructions • Installation Instructions
Control/Communicator

TABLE OF CONTENTS
Section 1: GENERAL DESCRIPTION .............................................................................. 6
Basic Hardwired..............................................................................................................6
Remote Keypads ............................................................................................................6
User Codes .....................................................................................................................6
Keypad Emergency Keys ...............................................................................................6
Backup Dialer .................................................................................................................6
Bell Output ......................................................................................................................7
Auxiliary Relay ................................................................................................................7
Built-in Indicators and Switches......................................................................................7
Programming ..................................................................................................................7
Communication Formats Supported ...............................................................................7
AC Power Input...............................................................................................................7
Auxiliary Power Output ...................................................................................................7
Back-Up Battery .............................................................................................................8
Agency Listings...............................................................................................................8
Section 2.: INSTALLING THE CONTROL ......................................................................... 9
Getting the Control Up and Running...............................................................................9
Mounting the Cabinet .....................................................................................................9
Installing the Lock ...........................................................................................................9
Mounting The Control's Circuit Board .............................................................................10
Standard Phone Line ......................................................................................................11
Enabling the Dialer .........................................................................................................11
Telephone Line Supervision ...........................................................................................11
Dialer Operation .............................................................................................................11
Connecting the AC Transformer .....................................................................................12
Earth Ground ..................................................................................................................12
Section 3: INSTALLING REMOTE KEYPADS ................................................................ 13
Wiring To The Keypads ..................................................................................................13
Mounting the Keypads ....................................................................................................14
Preliminary Check-out Procedure ...................................................................................14
Section 4: MECHANICS OF PROGRAMMING................................................................. 15
Entering Program Mode .................................................................................................15
Programming a Data Field..............................................................................................15
Exiting the Programming Mode ......................................................................................16
Section 5: BASIC HARD-WIRED ZONES 1-5 .................................................................. 17
General Information about Hardwired Zones .................................................................17
Wiring Devices To Zones 1-5 ........................................................................................17
Wiring 4-Wire Smoke/Combustion Detectors on Zones 1-5. ..........................................17
Wiring 2-Wire Smoke Detector .......................................................................................18
Fire Alarm Verification for Smoke Detectors ...................................................................19
Turning Off Fire Alarm Sounding ....................................................................................19
Programming Hard-Wired Zones ....................................................................................20
Check-Out Procedure For Detection Zones ...................................................................21
Section 6: SYSTEM ZONES ............................................................................................. 23
General Information ........................................................................................................23
System Zone Assignments .............................................................................................23
Section 7: ALARM INDICATING DEVICES ...................................................................... 24
General Information ........................................................................................................24
Sounder Connections ....................................................................................................25
Programming for External Sounders ..............................................................................25
Testing the Sounder .......................................................................................................26
Section 8: AUXILIARY RELAY CONNECTIONS ............................................................. 27
General Information ........................................................................................................27
Relay Connections .........................................................................................................27
Programming the Auxiliary Relay ...................................................................................28
Section 9. FINAL POWER UP .......................................................................................... 29
AC Power Connections...................................................................................................29
Earth Ground ..................................................................................................................29
Powering Up the System ................................................................................................30
Connecting The Back-Up Battery ...................................................................................30
Calculating the Battery Size ...........................................................................................30
Battery Supervision.........................................................................................................33
Section 10: Alpha Descriptor Programming .................................................................... 34

– 3–
Assigning Zone Descriptors ........................................................................................... 34
Entering Zone Descriptors ............................................................................................. 34
Programming the Descriptors ........................................................................................ 34
Alternate Method For Programming Zone Descriptors .................................................. 36
Adding Custom Words ................................................................................................... 37
ALPHA VOCABULARY LIST ......................................................................................... 38
CHARACTER (ASCII) CHART....................................................................................... 39
Section 11: SYSTEM COMMUNICATION ...........................................................................40
General Information ....................................................................................................... 40
Report Code Formats .................................................................................................... 40
TABLE OF CONTACT ID EVENT CODES .................................................................... 42
Programming Communication Options ......................................................................... 43
Section 12: Zone Response Type Definitions ..................................................................47
General Information ....................................................................................................... 47
Zone Response Types ................................................................................................... 47
Section 13: DATA FIELD DESCRIPTIONS.........................................................................49
Description of System Data Fields ................................................................................. 49
Section 14: REMOTE PROGRAMMING ..............................................................................56
General Information ....................................................................................................... 56
Equipment Required ...................................................................................................... 56
Initial Download ..............................................................................................................56
Remote Programming Information ................................................................................. 57
Section 15: SYSTEM OPERATION .....................................................................................58
User Codes ....................................................................................................................58
Keypad Functions ......................................................................................................... 59
Section 16: TESTING THE SYSTEM...................................................................................60
Dialer Test ......................................................................................................................61
Trouble Conditions ......................................................................................................... 61
General Information ....................................................................................................... 61
Telephone Line Failure .................................................................................................. 61
Power Failure ................................................................................................................. 61
Other Displays................................................................................................................61
Section 17: TROUBLESHOOTING GUIDE .........................................................................62
CONTACTING TECHNICAL SUPPORT ........................................................................ 63
Section 18: SPECIFICATIONS & ACCESSORIES .............................................................64
Specifications ................................................................................................................. 64
AGENCY LISTINGS ...................................................................................................... 65
Accessories ....................................................................................................................66
Sounders ........................................................................................................................66
Compatible 2-Wire Smoke Detectors............................................................................. 66
REGULATORY AGENCY STATEMENTS .................................................................................67
LIST OF FIGURES
Figure 1. Installing the cabinet lock..................................................................10
Figure 2. Mounting the 5110XM pc board......................................................... 10
Figure 3. Keypad connections to the Control board.......................................... 14
Figure 4. 4-wire smoke detector connections..................................................... 18
Figure 5. 2-wire smoke dectector connections................................................... 19
Figure 6. Sounder wiring ................................................................................... 25
Figure 7. Wiring the auxiliary relay output for unsupervised
alarm output........................................................................................ 27
Figure 8. Wiring the auxiliary relay output for 4-wire smoke
detector power usage........................................................................... 27
Ademco 5110XM Summary of Connections...............................Inside Back Cover

– 4–
HOW TO USE THIS MANUAL
This manual is written to accommodate both the new and the experienced installer of
Ademco products. A general description of the entire system is located at the
beginning of the manual. The wiring and physical setup of the hardware follows.
The sections at the core of the manual include both hardware setup and programming
requirements of each device to make that specific device operational in the system. A
checkout procedure is included at the end of each section. We recommend this method
to ensure that each device is working properly before proceeding to the next section. It
must also be used if you are making a particular addition to the system of one of these
devices.
Each of the sections covering the installation of peripheral devices includes the
programming for that device. Without an understanding of the programming of the
system, you will not be able to successfully perform the required programming in each
of these sections. We therefore urge you to read the Mechanics of Programming
section before any programming is performed.
If you are an experienced user of Ademco products, you may choose to wire and then
program the entire system at once. If so, refer to the Mechanics of Programming
section and the Data Field Descriptions section after the hardware setup is complete.
A blank pull-out programming form is included with this manual.
This manual uses various icons to denote critical notes and technical tips to assist you
with the installation of this system. These are easily seen in the left-hand column of
the relevant information.

– 5–
CONVENTIONS USED IN THIS MANUAL
MAIN SECTION TITLES ARE SHOWN IN REVERSE TYPE
Before you begin using this manual, it is important that you understand the meaning
of the following symbols (icons).
ULThese notes include specific information which must be followed if you are
installing this system for a UL Listed application.
These notes include information that you should be aware of before continuing
with the installation, and which, if not observed, could result in operational
difficulties.
This symbol indicates a critical note that could seriously affect the operation of
the system, or could cause damage to the system. Please read each warning
carefully. This symbol also denotes warnings about physical harm to the
installer.
Enter Zn Num.
(00 = Quit) 01
Many system options are programmed in an
interactive mode by responding to Alpha keypad
display prompts. These prompts are shown in a
double-line box.
∗00 When programming the system, data fields are
number.
PRODUCT MODEL NUMBERS: References to specific model numbers,
unless noted otherwise, represent Ademco products.

– 6–
Section 1. GENERAL DESCRIPTION
The Ademco 5110XM is a UL Listed, microprocessor-based fire alarm
control/communicator that supports 5 style B (for further explanation of
style B, refer to NFPA 72 National Fire Alarm Code Chapter 3: Protected
Premises Fire Alarm Systems) hardwired zones. It may be used as a slave
Digitial Alarm Communicator Transmitter (DACT) providing central or
remote station service for a central or remote station listed Fire Alarm
Control Panel (FACP). It may also be used as a standalone non-coded local,
central station or remote station control.
Basic Hardwired Zones
Provides 5 style B hardwired zones having the following characteristics:
• EOLR supervision supporting N.O./N.C. sensors such as smoke
detectors, water flow switches, etc. or N.O./N.C. contacts from a listed fire
alarm control panel
• 300 – 500ms response time
• Individually assignable to bell output and/or aux. relay
• Supports up to 16 2-wire smoke detectors on Zone 5
• Supports 4-wire smoke detectors on any zone (power to these should be
supplied from the control's auxiliary relay power output; see the section
on Hardwired Zones)
• Tolerance of 300-ohm resistance on zones 1-4, 100-ohm resistance on zone
5 (excluding EOLR)
Remote Keypads
• When used as a DACT only, a keypad is not required, but may be used to
provide supplementary status annunciation.
• When used as a control, a keypad must be used.
The following keypads may be used:
Fixed-Word Keypads: 6137 (gray) or 6137R (red)
Alpha Keypads: 6139 (gray) or 6139R (red)
A 6139 or 6139R keypad must be used for keypad programming.
User Codes (for use with remote keypads)
• 1 Master code for entire system (user 1– intended for use by installer)
• 5 secondary user codes (users 2–6; user 2 intended for use by principle
end user)
Keypad Emergency Keys
Provides up to 3 programmable emergency key functions:
• Designated as Zones 7, 95, and 96
• Can be programmed for 24-hr. silent, audible, auxiliary, or fire responses
• Intended to be used only when the 5110XM is installed as a stand alone
control.
Backup Dialer
Has built-in backup dialer for connecting to a second supervised telephone line.

– 7–
Bell Output Provides one 12VDC (nominal), 1 AMP output, which may be configured for
Style Y (for further explanation of style Y, refer to NFPA 72 National Fire
Alarm Code Chapter 3: Protected Premises Fire Alarm Systems), EOLR
supervision (for use with polarized alarm sounding devices) or for no
supervision (no EOLR used)
Auxiliary Relay
Provides a built-in 12V wet or dry (jumper selectable) "Form C" relay which can
be used for one of the following:
• Alarm activation on selected zones, silenced by Code + Off
• Trouble/Supervisory activation
• 4-wire smoke detector reset
• Battery saving feature (disconnects power from non-critical loads 4 hours
after AC power loss)
• Alarm activation on selected zones, silenced by Code + #67 (can be used for
elevator recall)
Built-in Indicators and Switches
• A built-in warning buzzer that provides alarm, supervisory, and trouble
sounds
• 7 LED indicators provide visual status of (1) AC Power, (2) Battery Trouble,
(3) Communication Failure, (4) Telco Line Fault, (5) Silenced Audible
Conditions, (6) Main Dialer Line Seize, and (7) Backup Dialer Line Seize
• A Silence/Reset push-button allows audible warnings to be silenced and
smoke detectors to be reset.
Programming Programmed options are stored in electrically erasable, non-volatile EEROM
memory (information can be reprogrammed at any time and will not be lost
in the event of a power loss). The system can be programmed by one of the
following methods:
• Uploaded, downloaded, or controlled via an IBM compatible computer, V-
Link software and a HAYES modem specified by Ademco
• Programmed through an alpha keypad (6139, 6139R)
ULRemote programming may only be used when a service technician is at the site
during downloading.
Keypad programming consists of:
• Data field programming
• Interactive (menu) mode programming
Communication Formats Supported
• Ademco Low Speed (Standard or Expanded)
• Sescoa/Radionics (Standard or Expanded)
• Ademco Express
• Ademco Contact ID
AC Power Input
Uses an enclosed, permanently-wired,120VAC transformer rated @ 18.0 VAC,
40VA (supplied) with manually resettable circuit breaker.
Auxiliary Power Output
Provides 12VDC, 350 mA maximum for peripherals such as keypads. Uses
Positive Temperature Coefficient Thermistors (PTCs) for protection. There are
no replaceable fuses.

– 8–
Back-Up Battery
Uses a rechargable 12VDC, 7AH/14AH maximum lead acid (gel cell) battery for
back-up power (dual battery cable supplied)
Agency Listings
• UL864/NFPA 72 Central and Remote Station DACT and Local, central
Station and Remote Station Control.
• FM pending
• CSFM pending

– 9–
Section 2. INSTALLING THE CONTROL
This section provides instructions for getting the system up and running quickly, as well as
detailed instructions for the following:
• Getting the control up and running
• Installing the cabinet lock
• Mounting the control cabinet
• Installing the main PC board
• Standard phone line connections
• Installing the back-up battery in the cabinet
• Connecting the AC transformer
• Making earth ground connections
Getting the Control Up and Running
The following procedure is recommended for getting the 5110XM up and
running quckly. Refer to each individual section (as indicated in parenthesis)
for a more detailed overview of each step:
1. Mount the cabinet, pc board and lock (*see the paragraphs following this
procedure for details on Mounting the Cabinet, and Installing the Lock)
2. Unpack the LED indicator pc board and plug it into the J5 header on the
5110XM PC board.
3. Wire the telephone lines, AC transformer, earth ground, optional remote
keypads (if used), zones and supplementary alarm sounders (if used). (refer
to the appropriate sections as required)
4. Program the control's telephone numbers and subscriber account numbers.
Select the desired report format and program the desired report codes.
Refer to the section on System Communications for more information on
related programming. A 6139 or 6139R must be used to program the
5110XM locally.
5. Revise the default program selection as required.
Refer to the sections on Mechanics of Programming and Data Field
Descriptors and the Program Form for details on the various programming
options.
6. If a remote keypad is to be permanently installed, program a user 2 code for
the system's principle user. The Master Code as programmed in field *20
is meant for the installer's use only and must not be given to the system's
user.
Refer to the section on System Operation for details on entering user codes.
7. Test the system to verify proper operation (refer to the section on TESTING
THE SYSTEM).
Mounting the Cabinet
Mount the control cabinet to a sturdy wall using fasteners or anchors (not
supplied), in a clean, dry area which is not readily accessible to the general
public. Four mounting holes are provided at the back of the cabinet. When
used as a slave DACT for a listed FACP, it is recommended (but not required)
that the 5110XM be mounted near the FACP.
Installing the Lock
Use an Ademco No. N6277 Cam Lock and No. N6277–1 Retainer Clip
(supplied).

– 10–
CABINET DOOR BOTTOM
RETAINER
CLIP
RETAINER CLIP
(NOTE POSITION)
RETAINER
SLOTS
LOCKED
UNLOCKED
Figure 1. Installing The Cabinet Lock
1. Remove the cabinet door. It is
easily removable for servicing
and is easily re-installed.
2. Remove the lock knockout from
the control cabinet door. Insert
the key into the lock. Position
the lock in the hole making cer-
tain that the latch will make
contact with the latch bracket
when the door is closed.
3. Hold the lock steady, and insert
the retainer clip into the
retainer slots. Position the clip
as illustrated in order to permit
easy removal.
Before installing the cabinet's contents, remove the metal cabinet knock-outs
required for wiring entry. Do not attempt to remove the knockouts after the
circuit board has been installed.
Mounting The Control's Circuit Board in The Cabinet
1. Hang three black mounting clips (provided) on the raised cabinet tabs (see
Detail B in Fig. 2).
2. Insert the top of the circuit board into the slots at the top of the cabinet.
Make sure that the board rests on the correct row (see Detail A ).
3. Swing the base of the board into the mounting clips and secure the board to
the cabinet with the accompanying screws (see Detail B in Fig. 2).
DETAIL B
SIDE VIEW OF SHORT
MOUNTING CLIPS
DETAIL A
SIDE VIEW OF
BOARD INSERTED
INTO SLOTS
Figure 2: Mounting the 5110XM PC Board