ADEMCO 4137AD User manual

SURFACE MOUNTING 4137ADK137AD CONSOLES
1. Mark the positions on the wall for the screw mounting holes and the
cut-out for the wiring.
2. Pull the interface wiring in the wall through the cut-out.
3. Remove the console’s back cover. The securing screw at the front
of the console (under the nameplate) must be removed to release
the back cover.
4. Pass tha interface wiring through the opening in the back cover,
then mount the back cover to the wall surface with screws.
5. Splice the interface wiring to the console harness wires and plug in
the harness connector. Insulated solderless wire splices (e.g., 311)
may be used for splicing.
6. Attach the main body of the console to the wall-mounted back
cover. The console is properly attached when it snaps into place.
Use the securing screw (previously removed) to secure the console
to the back cover.
Back cover of VISTA Console
that IS mounted to the wall
Pull interface wr!ng through hole
\ and splice to Console wres.
\ . \ VISTA Console
SPECIFICATIONS
4137AD, 5137AD REMOTE CONSOLES
1. Physical: 8.4”W x 4.75”l-l x 1 .l “D
(213mm x 121 mm x 28mm)
2. Electrical: Voltage Input: 12VDC
Current Drain: 60mA (4137AD)
9OmA (5137AD)
3. Interface Wiring: RED: 12VDC input (+)
BLUE: See Control’s instructions
GREEN: Data Out to Control
YELLOW: Data In from Control
BLACK: Ground,-and if used,
(-) connection from
supplementary power supply
(see Control’s instructions)
www.PDF-Zoo.com

J
OUTLINE OF INSTALLED UNIT
-------- ______ ------ -em----__------
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
TOP
l 7-3/v f
THIS CUT-OUT FOR FLUSH MOUNTING ONLY./
BEFORE CUTTING. REFER TO “FLUSH WALL
MOUNTING” IN THE INSTALLATION MANUAL
FOR COMPLETE INSTRUCTIONS. A
4-13/l 6”
1
*
\
SURFACE MOUNTING
HOLES (A, B) AND CUT-OUT (C) \
I L
I
I
!
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I . .
I
I
L------------------_--____--------
INSTRUCTIONS FOR SURFACE MOUNTING TO “SURFACE MOUNTING” AT LEFT FOR COMPLETE
1. USE THIS TEMPLATE TO MARK LOCATIONS OF HOLES TO BE INSTRUCTIONS.
DRILLED IN MOUNTING SURFACE. HOLES A ARE FOR P.SCREWS INSTALLED IN LOCATIONS A SHOULD HAVE THEIR
KEYSLOT MOUNTING; B ARE FOR OPIIONAL USE FOR EXTRA HEADS PROTRUDING APPROXIMATELY l/16” FROM THE
SECURITY OR FOR USE WITH THE ZONE LOCATOR CARD
(SEE OPPOSITE SIDE OF THIS TEMPLATE); CUT-OUT C IS MOUNTING SURFACE (l/8” WITH THE ZONE LOCATOR CARD
REQUIRED FOR WIRING ACCESS. BEFORE CUlTlNG, REFER DESCRIBED ON THE OTHER SIDE).
SURFACE/FLUSH MOUNTING TEMPLATE FOR CONSOLES
N421 iV4 1 Of93
www.PDF-Zoo.com

ADDRESSABLE CONSOLE DIP SWITCH SETTINGS
(4137AD, 5137AD)
I dn I UPF
UP l
UP
UP
i3
UP
UP
I ID
UP
3
UP
UP
I ID
I I “I I “I 1
1 I UP I UP 1 1
IMPORTANT!
PARTITIONED SYSTEM
The standard default USERS:
enables only these 4
addresses (ID O-3). Set at
least one console to one of
these addresses. Use
programming mode to enable
other console addresses.
NOTE:
Some versions of the 5137AD
console may have a g-position
DIP switch. The sixth switch
is not used with some
controls and should be put
in the UP position. Refer
to control’s installation
instructions.
ADDRESS “31”
Do not use address 31
with partitioned systems.
Address 31 causes the
console to operate in non-
addressable mode (e.g.,
operates like the earlier non-
addressable 5137 console).
Address 31 is intended for
use with controls that do not
support addressable consoles.
DIP SWITCH ON PCB
V \
FRONT VIEW
/ PC8v \
1 I
ADDRESSABLE CONSOLE
www.PDF-Zoo.com

ZONE LOCATOR CARD INSTALLATION’ INSTRUCTIONS
(FOR SURFACE MOUNTED 4137AD FiXED MESSAGE DISPLAY CONSOLES)
The Zone locator Card will serve as a handy reference to the user. Before starting the installation procedures, fill out
the card by writing the zone/sensor desctiptions on the lines provided or have the user fill in the information.
.-
A) Attach the self-adhesive rubber pads below the lower mounting C) Install and tighten the LOWER mounting screws first and then
holes of the case back. tighten the upper screws. Notice that the fiber washers and the
B) Screw the upper mounting screws to the mounting surface using rubber pads have created a space behind the case.
the included fiber washers (see diagram B). Do not tighten the
screws, leaving about l/8’ space between the mounting surface D) Insert the card as shown, positioning the slot in the card onto the left fiber washer.
and the screw heads. Hang the case back on the upper mounting
screws TAKlNG CARE TO POSITION THE CASE BETWEEN THE
SCREWHEADS AND THE WASHERS.
E) The card now pivots on the fiber washer.
rSPACE
FIBER WASHER
MOUNTING
SURFACE
LOWER
MOUNTING
SCREW
RUBBER PAD
FIBER WASHER
MOUNTING
SURFACE
E)
www.PDF-Zoo.com