adeptus 6+2 Drawer Wide Roll Cart 76169 User manual

ASSEMBLY INSTRUCTIONS
6+2 Drawer Wide Roll Cart
#76169 - Matte Black Finish
#76182 - White Finish
1/8
CUSTOMER SERVICE AND REPLACEMENT PARTS:
FOR FASTER SERVICE ON PARTS OR HELP, PLEASE GO TO OUR WEBSITE AT WWW.ADEPTUS.COM;
OR CALL TOLL FREE 1.888.ADEPTUS (1.888.233.7887) FOR ASSEMBLY QUESTIONS.
MON-FRI 10 A.M. TO 4 P.M. E.S.T., CLOSED HOLIDAYS
IF YOU CALL, PLEASE HAVE ON HAND:
•PRODUCT NAME AND STOCK NUMBER
•WHEN AND WHERE THE UNIT WAS PURCHASED
•P.O. NUMBER FROM THE BOTTOM OF THIS PAGE
IF WE ARE BUSY HELPING OTHER CUSTOMERS, PLEASE LEAVE YOU NAME AND NUMBER
TO RECEIVE A RETURN CALL.
YOUR RETAILER MAY ALSO PROVIDE SERVICE OR PARTS.
HELPFUL OVERALL:
•SAVE THESE INSTRUCTION SHEETS AND THE BOX UNTIL YOU ARE SATISFIED WITH THE ASSEMBLY.
•DO NOT GLUE THE PARTS OF THE UNIT TOGETHER UNLESS YOU HAVE TESTED THE ASSEMBLY FIRST.
•PERFORM THE ASSEMBLY ON A CLEAN HARD SURFACE USING THE FLATTENED CARTON OR A TOWEL
TO PROTECT THE SURFACE AND THE FINISH OF THE UNIT. DO NOT ASSEMBLE ON CARPET.
VISIT WWW.ADEPTUS.COM TO REGISTER YOUR PRODUCT AND SEE THE
COMPLETE ADEPTUS LINE. REGISTRATION IS REQUIRED FOR PARTS REQUESTS.
THANK YOU FOR YOUR PURCHASE AND WELCOM TO ADEPTUS!
NOTICE: THE WRITTEN INSTRUCTIONS CONTAINED HEREIN ARE COPYRIGHTED.

8

,$ &,,),,),'$,&, $$,!(&+,$ &$,
,),("&(",$,&$, $,"$,,)&,+,,,$$,
$,"&"$&$,",,&(", +, "(&,, "(,("&(",",&(",&",
,&,*&",",)&,(",")", #&$,
 ,($,",),")"$,$%
 ,")",$$,",&, &,&, , "&&,+(",&$,",,"$,,"$(
 +,$,")", "&$,&,$$,),$&",+(",&$

*.G  ([," >K[3)" [I))[
W/([ C-4[7[([ )2Q"4[ 4[3[
Q44([[ L-X+[4)08[-)&[)(4*7[
*-W7[43O(['([W7F1[([
([/; " ([4P[/4[)$43[)([
D4[4: %[E7I ""33V14[
")I[*/ 4[Q#9[(4H4/7[=U4[4J*4(34[
W(< )([([)/[34(34[
[/4K[334&Q"4[ B&[/W43[
A(3*)-7= )([([I/4N)$ ([
)375[IUMP[U4"*[YSX1[/; "4/[
!44*[7U4 /[*/ 43[ /43)(R"4[()I[
YSW/4[) ( ([=6&[4*@[
I 7P[?4[M[("[3B*[334&Q"[

ZYTW334&Q"4[YSW3H4r

@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@
127,&(7+(:5,77(1,16758&7,216CONTAINED +(5(,1$5(&23<5,*+7('

1
2
4
5
3
6
7
11
2
13
2X
6X
999
101010
888
888
999
101010
111111
12 13
13
10
14
A
Dowel
8.0 x 30mm 12
B
Screw
3.0 x 25mm 64
C
Screw
4.0 x 30mm 12
F
D
Drawer
Runner 16
E
(Ea) Caster and
(Eb) Caster Insert
Pair
04
Nail
1.5 x 19mm 44
1TOP
2RIGHT SIDE PANEL
3
4
LEFT SIDE PANEL
BACK PANEL
6
7
8
9
10
11
BACK CASTOR SUPPORT
FRONT CASTOR SUPPORT
SMALL DRAWER SIDE
SMALL DRAWER BACK
DRAWER BOTTOM
SMALL DRAWER FRONT
3/8
5MIDDLE CROSSBAR
12
13
14
LARGE DRAWER BACK
LARGE DRAWER SIDE
LARGE DRAWER FRONT
TIP: DOWELS (PART A) VARY EVER SO SLIGHTLY.
IF A DOWEL (PART A) IS LOOSE
WE PREFER YOU CALL OUR TOLL FREE NUMBER
FOR ADDITIONAL DOWELS -
VS GLUING THE DOWEL.
IF YOU CHOOSE TO GLUE THE P
ARTS,
COMPLETELY TEST THE ASSEMBLY FIRST.
WE DO NOT SUPPLY GLUE.
127,&( 7+(:5,77(1 ,16758&7,216
CONTAINED +(5(,1$5(&23<5,*+7('

2
A
A
D
D
D
D
D
D
D
D
1
8,0 x 30mm
A=12 Dowel D=16
A
PREPARE PARTS FOR ASSEMBLY
• PUSH THE DOWELS (PART A) INTO THE EDGES
OF THE FOLLOWING PARTS, AS SHOWN:
(PART 2) RIGHT SIDE
(PART 3) LEFT SIDE
(PART 6) BACK CASTOR SUPPORT
(PART 7) FRONT CASTOR SUPPORT
NEXT PREPARE CASTER SUPPORTS:
• USE A HAMMER OR RUBBER MALLET TO INSERT
CASTER INSERT (PART Eb) INTO THE BOTTOM OF
THE FRONT CASTER SUPPORT (PART 7) AND
BACK CASTER SUPPORT (PART 6)
• TAP ABOVE THE BACK OF THE CASTER (ABOVE
THE STEM) TO ASSEMBLE CASTERS (PART Ea)
INTO THE CASTER INSERT (PART Eb).
1st
3rd
2nd
D
6
7
AAA
A
AAAA
Ea
Eb Eb
Ea
Eb
Ea
Eb=04
Ea=04
Ea
Eb
Ea
Eb
4/8
A
A
3
D
D
D
D
D
D
D
G
Drawer Runner Caster & Insert
Perform the entire assembly on a
clean, hard surface using the
flattened box or a towel to protect
the surface and the unit's finish. DO
NOT assemble on carpet.
Carpet creates too much bounce
making assembly difficult and could
lead to damage of the parts.
ATTACHING DRAWER RUNNERS:
• THE DRAWER RUNNERS (PART D) WILL STRETCH
SLIGHTLY AS YOU HAMMER THEM INTO PLACE.
• LINE UP THE PIPS IN DRAWER RUNNERS (PART D)
TO THE PRE-DRILLED HOLES IN THE RIGHT SIDE
PANEL (PART 2).
• EASE THE PIPS INTO THE HOLES BY TAPPING EACH
PIP DOWN HALF WAY. START ON ONE END, THEN
THE MIDDLE, THEN THE OTHER END.
• WHEN ALL 3 PIPS ARE HALF WAY DOWN AND THE
DRAWER RUNNER (PART D) IS STRETCHED,
HAMMER THE RUNNER ALL THE WAY DOWN UNTIL
IT IS FLUSH WITH THE RIGHT SIDE
PANEL (PART 2).
• REPEAT THESE STEPS TO ATTACH THE
DRAWER RUNNERS (PART D) TO THE
LEFT SIDE (PART 3).
TIP: Using a regular
hammer to attach the
runners provides a
clearer line of sight than
a rubber mallet.
127,&( 7+(:5,77(1 ,16758&7,216
CONTAINED +(5(,1$5(&23<5,*+7('

2ATTACH THE SIDES TO THE CROSSBARS
C
Screw 4,0 x 30mm
C= 6
5/8
2
3
5
7
6
c
c
cc
cc
ATTACH ONE SIDE FIRST AND THEN THE OTHER.
• PLEASE CHECK THAT THE DISTANCES
MATCH TO THE SQUARE DIAGRAM.
• SECURE BACK CASTER SUPPORT (PART 6) TO THE LEFT
SIDE (PART 3) USING SCREW (PART C).
SEE THE ROUND DIAGRAM, A BLOW UP IMAGE OF THE SCREW
POSITIONING TROUGH THE ANGLED POCKET HOLES.
• SECURE FRONT CASTER SUPPORT (PART 7) WITH SCREWS
(PART C) TO THE LEFT SIDE (PART 3) IN THE SAME MANNER.
• CAREFULLY TURN LEFT SIDE (PART 3) TO ITS BACK EDGE,
AS SHOWN IN THE DIAGRAM.
• POSITION RIGHT SIDE (PART 2) TO LINE UP THE CROSSBARS
(PART 6 AND 7) AT THE DOWEL HOLES AT BASE OF THE RIGHT SIDE
(PART 2).
• SECURE CASTER SUPPORTS (PART 6 AND 7) TO RIGHT SIDE
(PART 2) USING SCREW (PART C) AND SHOWN IN THE DIAGRAM. TIP:
HAND TIGHTEN FOR THE BEST FIT.
• ATTACH (PART 5) MIDDLE CROSSBAR TO BOTH SIDES OF
THE UNIT AT THE SIDE DRILLED HOLE.
DO NOT USE A DRILL. HAND TIGHTEN.
3ATTACH THE TOP
Screw 4,0 x 30mm
C= 6
C
1
c
c
c
c
c
•
•
DO NOT STAND LEFT SIDE (PART 3) UP
ON THE EDGE YET. TO EASE ASSEMBLY,
LAY SIDE FLAT ON THE FLOOR, RUNNER
SIDE VISIBLE.
MATCH UP BACK CASTER SUPPORT
(PART 6) AND FRONT CASTER SUPPORT
(PART 7) AT DOWEL HOLES LOCATED AT
THE BOTTOM OF SIDE .
TIP: This
step is
easier with
two people.
TIP: Turning the
unit upside
down provides a
better angle to
tighten the
screws.
• LINE UP THE DOWEL HOLES IN TOP (PART 1)
WITH DOWELS THE IN UNIT´S SIDES.
• SEE ROUND DIAGRAM:
SLIDE (PART C) SCREWS THROUGH ANGLED
POCKET HOLES.
AND HAND TIGHTEN FOR BEST FIT.
127,&( 7+(:5,77(1 ,16758&7,216
CONTAINED +(5(,1$5(&23<5,*+7('

4
F
FF
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
4ATTACH THE BACK PANEL
89
10
11
8
8
B
F
F
F=28
6X
5ASSEMBLE THE SMALL DRAWERS
3,0 x 25mm
B=48 F=12
6/8
Nail
Nail
Screw
F
FF
F
F
F
F
F
F
F
F
F
Use all back
panels nails.
Evenly spaced,
they help make
the unit strong.
TIP: To make this step easier, place the drawer upside
down on a counter with the drawer front hanging off
the edge. This will allow the drawer box to lay flat and
provide better control for hammering the nails.
• HOLD THE (PART 4) BACK PANEL IN THE
GROOVES INSIDE THE UNIT´S SIDES.
• ALSO MAKE SURE THE BACK PANEL
FITS IN THE
GROOVE AT THE BACK OF THE TOP.
• CHECK THAT THE UNIT IS SQUARE.
• SECURE THE (PART 4) BACK PANEL USING THE (PART F)
NAILS.
• LINE UP THE BOTTOM EDGE OF THE DRAWER
SIDE (PART 8) WITH THE BOTTOM EDGE OF THE
DRAWER FRONT (PART 11).
• JOIN THE PARTS USING TWO SCREWS (PART B)
AS SHOWN IN THE DIAGRAM.
NOTE: THE SCREWS' SHARP TIPS ARE SELF TAPPING, SO THE
DRAWER FRONT DOES NOT NEED A PILOT HOLE. THE SHARP
TIP STARTS THE HOLE, AND THE SCREW THREADS WILL
SECURE THE PART IN PLACE FOR A TIGHT FIT.
• REPEAT ON THE OTHER SIDE OF THE DRAWER.
• SLIDE IN DRAWER BOTTOM (PART 10) TROUGH
GROOVES IN THE DRAWER SIDES (PART 8). THIS WILL
START SQUARING UP THE DRAWER.
• LINE UP DRAWER BACK (PART 9) WITH BOTH DRAWER
SIDES (PART 8). CHECK THAT IT IS SQUARE.
• SCREW THE DRAWER BACK (PART 9) TO THE DRAWER
SIDES (PART 8).
• TURN THE DRAWER OVER. CONFIRM THE DRAWER BOTTOM
(PART 10) COVERS THE DRAWER BACK (PART 9). NAIL THE
DRAWER BOTTOM (PART 10) THROUGH TO THE DRAWER
BACK (PART 9) USING (2) NAILS (PART F).
127,&( 7+(:5,77(1 ,16758&7,216
CONTAINED +(5(,1$5(&23<5,*+7('

6ASSEMBLE THE LARGE DRAWERS
3,0 x 25mm
B=16 F=04
• LINE UP THE BOTTOM EDGE OF THE LARGE DRAWER
SIDE (PART 13) WITH THE BOTTOM EDGE OF THE
LARGE DRAWER FRONT (PART 12).
• JOIN THE PARTS USING TWO SCREWS (PART B) AS
SHOWN IN THE DIAGRAM.
• REPEAT ON THE OTHER SIDE OF THE DRAWER.
• SLIDE IN DRAWER BOTTOM (PART 10) TROUGH
GROOVES IN THE BIG DRAWER SIDES (PART 13).
THIS WILL START SQUARING UP THE DRAWER.
• LINE UP DRAWER BACK (PART 14) WITH BOTH DRAWER SIDES
(PART 13). CHECK THAT IT IS SQUARE.
• SCREW THE LARGE DRAWER BACK (PART 14) TO THE
LARGE DRAWER SIDES (PART13)
• TURN THE DRAWER OVER.
CONFIRM THE DRAWER BOTTOM (PART 10) COVERS THE DRAWER BACK
(PART 14). NAIL THE DRAWER BOTTOM (PART 10) THROUGH TO THE
LARGE DRAWER BACK (PART 14) USING (2) NAILS (PART F).
10
13
12
14
F
F
F
13
7INSERT DRAWERS AND COMPLETE ASSEMBLY
• THE DRAWER SIDES HAVE A CHANNEL THROUGH THE
MIDDLE OF THE PART. THIS CHANNEL SLIDES OVER
THE DRAWER RUNNERS (PART D).
• SLIDE ALL DRAWERS IN.
CHECK THE DRAWERS RUN SMOOTH.
ONE DRAWER FRONT SHOULD NOT OVERLAP
ANOTHER DRAWER FRONT EDGE.
• STEP BACK TO LOOK AT UNIT. YOU MAY PREFER TO
MOVE ONE DRAWER TO ANOTHER´S POSITION.
7/8
Screw Nail
TIP: To make this step easier, place the drawer upside
down on a counter with the drawer front hanging off
the edge. This will allow the drawer box to lay flat and
provide better control for hammering the nails.
NOTE: THE SCREWS' SHARP TIPS ARE SELF TAPPING, SO THE
DRAWER FRONT DOES NOT NEED A PILOT HOLE. THE SHARP TIP
STARTS THE HOLE, AND THE SCREW THREADS WILL SECURE THE
PART IN PLACE FOR A TIGHT FIT.
IF THERE IS A PROBLEM, IT IS LIKELY THE DRAWER FRONT IS NOT
ASSEMBLED LEVEL. SIMPLY BACK OUT ONE SET OF THE SCREWS
ON A DRAWER SIDE AND ADJUST UNTIL IT IS TO YOUR
SATISFACTION.
REMEMBER TO LINE UP THE BOTTOM EDGES OF THE DRAWER
SIDE AND DRAWER FRONT.
127,&( 7+(:5,77(1 ,16758&7,216
CONTAINED +(5(,1$5(&23<5,*+7('

COMPLETED ASSEMBLY:
THANK YOU FOR YOUR PURCHASE, AND WELCOME TO ADEPTUS!
8/8
USE AND CARE INSTRUCTIONS:
CARE INSTRUCTIONS:
• NORMAL USE: WIPE WITH A CLEAN CLOTH.
• WHEN NEEDED TO CLEAN SCUFFS:WIPE CLEAN WITH A SLIGHTLY DAMP CLOTH AND A MILD
CLEANER. THEN WIPE DRY WITH A CLEAN CLOTH.
USE:
MULTI-PURPOSE MOBILE STORAGE UNIT FOR HOME, OFFICE, CRAFT ROOM, KITCHEN, OR GARAGE .
127,&( 7+(:5,77(1 ,16758&7,216CONTAINED +(5(,1$5(&23<5,*+7('