Enclume PR33 User manual

Enclume Scrolled Arm Oval Cookware Rack
PR33
Enclume racks are the ultimate in
Quality, design, strength and function.
Congratulations for owning one of the finest
Storage racks made.
WARNING:
READ ALL OF THE INSTRUCTIONS
BEFORE ASSEMBLING AND USING
YOUR RACK.
All of our hammered steel racks are finished with an industrial wax designed to
give years of protection to the rack. Cleaning is easily done with a damp cloth. Dry
thoroughly after cleaning. If a touch-up is ever needed we recommend a "Pledge"
like wax product.
Enclosed you will find everything needed for the assembly
and use of your storage rack. Two people make assembly
and installation easier. The parts and hardware included are:
Hardware included:
4 – 3/8” x 3/4” Button Head Screws
2 – 3/8” x 1” Button Head Screws
6 –3/8” Nuts
2 – Ceiling Screw Hooks (Large)
2 – 5” Extension Hooks
1 – 7/32” Allen Wrench
12 – Angled Pot Hooks
12 – Straight Pot Hooks
2 – Grid Brackets
Toggle Kit
Components included:
1 – Oval Base
1 – Grid
4 – Arms
1 – Upper
4 – “L” shaped Grid Brackets
See reverse side for ASSEMBLY AND INSTALLATION INSTRUCTIONS
Limited Warranty:This product is warranted to be free of material defects for a period of five years from the date of purchase. Customer's exclusive remedy shall
be the repair or replacement of the defective product and shall be subject to the following conditions: (1) notice of any defect is received by Enclume within the
warranty period and (2) customer returns the defective product to Enclume Design Products, Inc. , 24 Colwell St.. , Port Hadlock, WA 98339, postage prepaid
within 20 days following a return authorization number (which may be obtained by telephoning the number at the bottom of this instructions) being provided to the
customer by Enclume. There are no other warranties, expressed or implied. THERE ARE NO WARRANTIES OF MERCHANTABILITY OR FITNESS
FOR A PARTICULAR PURPOSE. ENCLUME SPECIFICALLY DISCLAIMS ANY AND ALL INCIDENTAL OR CONSEQUENTIAL DAMAGES
ARISING OUT OF THE PURCHASE OR USE OF ENCLUME'S PRODUCTS.
::
potracks.com Call 1-800-667-8721 anywhere in the US and Canada - www.kitchensource.com
::potracks.com
powered by ::kitchensource.com

ASSEMBLY AND INSTALLATION INSTRUCTIONS for PR33
Hardware included:
4 – 3/8” x 3/4” Button Head Screws
2 – 3/8” x 1” Button Head Screws
6 –3/8” Nuts
2 – Ceiling Screw Hooks (Large)
2 – 5” Extension Hooks
1 – 7/32” Allen Wrench
12 – Angled Pot Hooks
12 – Straight Pot Hooks
4 – “L” shaped Grid Brackets
Toggle Kit
Components included:
1 – Oval Base
1 – Grid
4 – Arms
1 – Upper
Rack Assembly
1) If your rack is stainless steel it is best to keep the tissue on during installation to avoid fingerprinting.
2) Place rack body (also called the oval) on the floor or other “firm” surface.
3) Attach the four arms to the OUTSIDE of the oval using the 3/8” x 1/4” button head screws. From the outside, thread the button
head through the arms, the oval and grid bracket (long side down). Secure with 3/8” Hex nut. Make sure the arm orientation is
correct. The 90 degree bend is facing towards the center of the rack and is approximately even with the bottom of the rack body.
Leave the four button head screws slightly loose.
4) Attach the upper bar to the four arms using the two longer screws, and two nuts. Insert the extension hooks into the holes in the
upper bar.
5) Square up the arms and tighten all the screws with the Allen wrench. The assembly is now complete.
6) Carefully place the grid (from one end) between the arms until it fits into the oval and rests on the arm tabs for support. Two
people make this step easier.
7) We recommend that you anchor your rack into the solid wood of ceiling joists or beams. Carefully measure the area where the
rack is to be hung and install the ceiling screw hooks directly into the wood joists. If it is not convenient to hang your rack
directly into wood joists you may use the new-technology DRYWALL anchors enclosed with your rack. The steel anchors are
very strong and when installed in drywall will hold 200 lbs. each. Two anchors hold about 400 lbs. Follow the instructions in
the Toggler kit.
8) Hang your heavier items on the straight portion of the rack between the hanging arms or from the upper bar between the
extension hooks.
9) All of our hammered steel racks are finished with an industrial wax designed to give years of protection to the rack. Cleaning is
easily done with a damp cloth. Dry thoroughly after cleaning. If a touch-up is ever needed we recommend a "Pledge" like wax
product.
10) The grid has been treated with a finish which will resist corrosion and tarnish. It can be cleaned with a damp cloth and dried
thoroughly. Please do not use abrasive cleaners.
It is important that your rack is assembled correctly. If the unit is assembled or used
incorrectly, it could become unstable and collapse, possibly causing injury.
WARNING
::
potracks.com Call 1-800-667-8721 anywhere in the US and Canada - www.kitchensource.com
::potracks.com
powered by ::kitchensource.com