Adidas ADBE-10244 User manual

ADBE-10244 MULTI PURPOSE BENCH
ASSEMBLY INSTRUCTONS

EXPLODED DIAGRAM

PARTS LIST
NO. DESCRIPTION QTY NO. DESCRIPTION QTY
1 BARBELL CRUTCH 2 20 WEIGHT TUBE 2
2 MAIN BASE 1 21 HEX BOLT(M10*135MM) 2
3 SUPPORT BAR 1 22 WASHER (M10*25MM) 3
4 CENTRAL BRACE 1 23 HEX NUT(M10*12MM) 2
5 FRONT LEG 1 24 WEIGHT CLIP 3
6 LEG LIFT 1 25 FOAM TUBE 2
7 LEFT BUTTERFLYARM 1 26 PLASTIC KNOB 2
8 BACKREST SUPPORT 2 27 ROLLER PADS 6
9 BACKREST 1 28 HEX BOLT(M8*40MM) 4
10 SEAT 1 30 SQUARE PLUG(25.4MM) 4
10L SAFETY HOOK 1 31 ROUND HEAD PHILLIPS
4
10R SAFETY HOOK 1 32 HEX BOLT(M8*60MM) 2
11 HEX NUT(M8*8MM) 17 33 HEX BOLT(M8*15MM) 1
12 BUFFER BUSHING 2 34 FOAM TUBE 2
13 CARRIAGE BOLTS(M8*50MM) 10 35 HEX NUT(M8*10MM) 1
14 WASHER(M8*25MM*2.0MM) 20 36 ROUND PLUG(25.4MM) 2
16 SQUARE PLUG(38MM) 11 37 WEIGHT TUBE 1
17 BACKREST HT. BAR 1 39 BUFFER BUSHING 1
18 RIGHT BUTTERFLYARM 1 40 HEX BOLT(M10*60MM) 1
19 HEX BOLT(M8*50MM) 3 42 WASHER (M6*16MM) 4

PARTS CHECK LIST

HARDWARE PACK CHECK LIST

ASSEMBLY STEPS
**PLEASE DO NOT FULLY TIGHTEN UNTILASSEMBLY IS COMPLETE.
STEP 1
ATTACH TWO BARBELL STANDS (1) ONTO MAIN BASE(2) AND FASTEN WITH 4 CARRIAGE BOLTS M8*50 (13), 4
WASHER 8*25MM (14) AND 4 HEX NUT M8 (11). ATTACH THE SUPPORT BAR (3) ONTO BARBELL STAND (1) AND
FASTEN WITH 4 CARRIAGE BOLTS M8*50 (13), 4 WASHER 8*25MM (14) AND 4 HEX NUT M8 (11). FOLLOW THE
DIAGRAM TO ATTACH SAFETY HOOK (10L) AND SAFETY HOOK (10R) ONTO BARBELL STANDS (1) FIRSTLY
REMOVE THE PRE-INSTALLED NUTS AND RE-ATTACH AFTER THE SAFETY HOOKS ARE INSTALLED CORRECTLY.
INSTALL BACKREST BAR (17) THROUGH BARBELL STANDS (1) AT CORRECT HEIGHT.

STEP 2
ATTACH FRONT LEG (5) ONTO CENTRAL BRACE (4) AND FASTEN WITH 2 HEX BOLT M8*60MM (32), 2 WASHER
8*25MM (14) AND 2 HEX NUT M8 (11). FASTEN ANOTHER HEX BOLT M8*15MM (33) WITH WASHER 8*25MM (14)
FROM UNDERNEATH OF BRACKET ON FRONT LEG (5).
ATTACH CENTRAL BRACE (4) ONTO BARBELL STAND WHICH IS ASSEMBLED IN STEP 1 WITH 2 CARRIAGE
BOLTS M8*50MM (13), 2 WASHER 8*25MM (14) AND 2 HEX NUT M8 (11)
FIT SEAT (10) ONTO CENTRAL BRACE (4) AND FASTEN WITH 4 ROUND HEAD PHILLIP SCREWS M6*15MM (31)
AND WASHER 6*16MM (42). ATTACH TWO BACKREST SUPPORTS (8) ONTO THE SHAFT OF THE CENTRAL
BRACE (4) AND HOLD THEM. ATTACH BACKREST (9) ONTO BACKREST SUPPORT (8) AND FASTEN WITH 4 HEX
BOLT M8*40 (28) AND 4 WASHER 8*25MM (14).

STEP 3
ATTACH LEG LIFT (6) ONTO FRONT LEG (5) AND FASTEN WITH HEX BOLT M10*63MM (40), WASHER 10*25MM (22)
AND HEX NUT M8 (35). INSTALL WEIGHT TUBE (37) THROUGH LEG LIFT (6) AND FASTEN WITH HEX BOLT
M8*50MM (19), WASHER (8*25MM) (14) AND HEX NUT M8 (11), THEN ATTACH RUBBER CAP (39) TO END OF
WEIGHT TUBE (37).
INSTALL LEG LIFT PAD BAR (34) THROUGH EACH END OF THE LEG LIFT (6); ATTACH 4 ROLLER PADS (27) ON
BOTH SIDES OF EACH LEG LIFT PAD BAR (34).

STEP 4
ATTACH LEFT BUTTERFLY ARM (7) TO BARBELL STAND USING HEX BOLT M10*133 (21), WASHER 10*25MM (22)
AND HEX NUT M10 (23). INSTALL THE WEIGHT TUBE (20) THROUGH LEFT BUTTERFLY ARM (7) AND FASTEN
WITH HEX BOLT M8*50MM (19), WASHER 8*25MM (14) AND HEX NUT M8 (11). ATTACH FOAM TUBE (25) ONTO
LEFT BUTTERFLYARM (7) AND SECURE WITH PLASTIC KNOB (26), AFTERWARD ATTACH ROLLER PADS (27) ON
IT.
REPEAT THE ABOVE PROCEDURES ON RIGHT BUTTERFLYARM (18).
**PLEASE FULLY TIGHTEN ALL FASTENERS OF ENTIRE EQUIPMENT.