Adonis WX-2400 User manual
TO BATTERY
WIRELESS MOBILE MICROPHONE
MODEL WX-2400 INSTRUCTION MANUAL
Thank you very much for your purchase of “ADONIS” Wireless Mobile Microphone model WX-2400.
The model WX-2400 is non-directional high-performance mobile microphone with wireless method(between
microphone and control box) by weak radio wave, Integrated microphone and TX/RX Switch and Non-modulation
Prevention circuit with alarm.
Before using, please read this instruction carefully and use this microphone regularly for a long time.
★Matters to be attended to★
！DangerNever re-install or adjust the microphone during driving a car. Be sure to adjust the microphone before actual use.
！DangerBe sure to fix the cords and mount the microphone avoiding the possible trouble for safety driving.
！Warning Do not pull or wind the cords by force . It may cause a traffic accident.
！WarningThe inside of this microphone is already adjusted and never modify or adjust the unit.
！CautionDo not make impact on the microphone. It may cause a trouble or damage.
！CautionThis unit is not waterproof construction. Be sure to keep this unit dry.
！Caution Do not use this unit in the place of direct sunlight, high moisture and temperature, or poorly ventilated place.
！CautionDo not pull or insert the plug and jack under wet condition.
！CautionThis unit is exclusively available with DC12V(
±
2V)power source.
！CautionThis unit is not designed for emergency communication purpose. Please note.
★Warning and Note★
·Do not use this unit nearby microwave oven or electronic products equipped with “blue-tooth”. Please note there may be a
case not to use this unit depending on the environmental condition according to a radio wave, noise and mounting
surroundings.
·When finding any malfunction or damage on operation of this unit, stop your use and contact the dealer.
·Please note we are not responsible for the trouble caused by disassembly, modification and mistake on use.
·Do not use and put the unit in the place of full sunlight or high temperature.
·The design and specifications are subject to change without advance notice.
★PART NAMES★(Please refer to the illustration.) (Fig. 1)
④③②①⑦⑧⑨⑩⑫⑬⑭ ①MICROPHONE
②TX BUTTON
③RX BUTTON
④TX/RX CONTROL PART
⑤CONNECTING CABLE
⑤ ⑮ ⑥BATTERY CASE(TRANSMITTER)
⑦CONTROL BOX
⑧OUTPUT ADJUST. VOLUME
⑨TX INDICATOR LAMP（LED）
⑩POWER FEEDING LINE( RED)
⑪８ＰINTERCONNECT. JACK
TRANSCEIVER （８Ｐ ADONIS ARRANGE）
⑥ ⑪
ACCESSORY
⑫MAGIC TAPE LARGE（１PC.）
⑬MAGIC TAPE SMALL (2 PCS.)
⑭LITHIUM BATTERY(COIN TYPE)
⑮POWER FEED. CONNECTOR
MIC. CONVERSION CABLE
(ADONIS OPTION)
※MIC. CONVERSION CABLE IS NOT PROVIDED TO THIS UNIT.
★HOW TO MOUNT AND CONNECT★
· Put the ④TX/RX CONTROL PART on flat space of steering wheel by using
accessory magic tape small⑬(Fig.2) The ⑬Magic tape(small) should be put on
the place not to cause trouble for safety driving after cleaning the space to put on.
· Insert the coin type Lithium Battery⑭into ⑥TX BATTRY CASE. (Fig.6a)
· Put the ⑥TX BATTERY CASE on flat space of the other(hidden) side of steering
wheel by using the accessory magic tape(small)⑬.(Fig. 2) The place to put ⑬
Magic Tape(small) should be cleaned before put. The ⑤CONNECTING CABLE
should be put on steering wheel closely and firmly so that the driver does not
have any trouble for safety driving.
！WARNINGDO NOT MOUNT ON THE HORN SWITCH OR AIR-BAG.
IT IS VERY DANGEROUS.
· Mount the ⑦CONTROL BOX with accessory Magic Tape(large)⑫to the place
where you may watch the ⑨TX Indicator Lamp (LED).
· Connect the Mic. Conversion cable suitable to the transceiver(Optional) between
⑪８ＰINTERCONNECT. JACK and transceiver.(Fig.1)
（The Microphone Conversion Cable has a directional characteristics. Please
check it before connecting.）
（Fig.2）Put④TX/RX Control Part onto Handle
④
TX/RX CONTROL
⑥
Battery Case
ADONIS ELECTRONICS CORPORATION
TEL(072)893‑3111FAX(072)891‑2240
（Fig.５）8P ADONIS ARRANGEMENT
· Connect the⑩POWER FEEDING LINE (RED) to the (+) side of transceiver Power Source with accessory ⑮POWER FEED.
CONNECTOR (DC12V±2V) (Fig. 3)
※If the transceiver microphone terminal has a output of DC Power feeding, DC5V〜9V 50mA, “D” Series microphone
conversion cable, optionally available, can be connected directly with getting the DC Power from transceiver microphone
terminal. The wiring of Power Feeding Line (RED)⑩is not required.
★⑮HOW TO CONNECT POWER FEEDING CONNECTOR★（Fig. 3）
1. Put the (+) side power cord of transceiver and Microphone
Power Feeding Line (Red) on grooves in the connector.
2. Fix them tentatively.
3. Press the insulation cover down to be locked with pliers.
1. E: Earth (Microphone Signal) … Shield
2. M: Microphone Signal …. Yellow
3. P: PTT(press to talk) …. Red
4. G: Earth (for PTT) …. Purple
5. U: Up …. Green
6. D: Down …. White
7. C: U/D Common …. Orange
8. B: DC Power Feeding(+) …. Gray
★HOW TO USE★
· Press the ②TX BUTTON and the ⑦CONTROL BOX sounds out “pip” and TX INDICATOR lights up for indicating the
transmitting condition.
· Press the ③RX BUTTON and the ⑦CONTROL BOX sounds out “peep” ⑨TX INDICATOR(LED) lights off. The condition is
returned to RX (Receiving) mode.
· The Output Level is factory-preset to optimum level. But, the modulation level is too deep or shallow, the level can be
adjusted to appropriate level under following procedure.
Rotate the ⑧OUTPUTADJUSTMENT VOLUME to “Clockwise” for increase of output volume. Rotate it to “Anti-Clockwise”
to decrease volume. Under monitoring by Local Station, rotate it with “minus” driver carefully in the rotation range indicated
at (Fig.4). It turns 90°only for both left and right. Excessive turnmay damagethe ⑧OUTPUT ADJUSTMENT VOLUME.
Please be careful.
★NON-MODULATION PREVENTION CIRCUIT★
In case you set the condition to Transmitting mode without any intention, the
condition of non-modulation will continue and it may cause trouble to other
stations. To prevent such a condition, the alarm circuit built-in will activate
after 2.5 minutes continuous transmitting. The alarm sounds for 30 seconds
and the condition will be reset to receiving mode automatically.
If you want to continue Transmitting just after alarm sound, press the ③RX
BUTTON for stopping Transmitting Mode, then, press the ②TX BUTTON to
change to the transmitting mode.
※CAUTION
After pressing the ②TX BUTTON、the microphone may turn to transmitting or
receiving condition with “pip” or “peep” sound without control of microphone.
This condition is caused by imperfect positional adjustment between ⑥TX
BATTRY CASE and ⑦CONTROL BOX.
In this case, Non-Modulation Prevention circuit activates and after 2 or 3
minutes of continuous transmitting condition, the condition will return to
receiving mode automatically. However, Alarm circuit does not activate and
no alarm sounds from the unit It looks as the transmitting condition is
interrupted on the way of transmitting. Please be careful to this phenomenon.
In such a case, change the mounting position of ⑦CONTROL BOX.
★HOW TO REPLACE THE COIN TYPE LIGTHIUM BATTERY★
When you cannot control TX/RX from ④TX/RX CONTROL PART, ⑭Coin Type Lithium Battery is dead. Replace the battery to
new one as following order.
（A）Take ⑭Coin type Lithium Battery from ⑥Battery Case(TX) withtoothpick or stick. ( Push it out from ④TX/RX CONTROL
PART.) (Fig. 6b).
（B）Press the new ⑭Coin Type Lithium Battery (CR2032) into the ⑥Battery Case(TX) while keeping the (+) pole of battery
upper side. (Fig. 6a)
★RF FEEDBACK NOISE★
When transmitting with low power, the noise may be negligible. But when transmitting high-power, there are possibilities to
have abnormal modulation interference with offensive soundand other noise. In such a case, the bad matching between antenna
and coaxial cable may cause the problems., i.e., the Standing Wave effects onto microphone cable. To get the better condition,
please do not place the microphone cable in parallel to the antenna coaxial cable. Also please check the SWR between
antenna and transceiver.
SPECIFICATIONS:・Non-Directional Electret Condensor Microphone 1pc.・Cord Length of 8P Interconnect. Jack 70cm
・Matching Output Impedance 500 〜50KΩ・Output Voltage 0〜50mV(rms)
・Power Voltage: TX Battery Case… Coin type Lithium Battery CR2032 x 1(DC3V) totaling 10 hours (For Transmitting)
Control Box…by Mic. Cable (“D” Series)… DC5V〜10V, by Power Feeding Line(Red)…DC12V±2V
・Size and Weight: MIC. TX/RX Control Part…20(H) x 30(W) x 8(D)mm 5g TX Batt. Case..13(H)x33(W)x45(D)mm 15g
Control Box.. 90(H)x50(W) x 25(D)mm 200g
Operating Frequency 2.4GHz band digital Effective Receiving Distance… about 1m from TX Battery case
（Fig.３）
（Fig.４）OutputAdjust Volume
（Fig. 6）Replacement of Battery
(a) (b)
Toothpick etc.
※
Caution: Please be sure to have always
spare ⑭
coin type Lithium battery so
you may change it immediately when
you find the battery power is out. (You
cannot control theTX or RX.)
Other Adonis Microphone manuals
