adpower Wattman HPM-100A User manual

- 1 -
Consumption/Standby
Power Meter
Manual
Product Name : Wattman (HPM-100 )
D Power Co., Ltd

- 2 -
CONTENTS
1. Product Introduction -------------------------------------------------------- 3
2. Power Measurement -------------------------------------------------------- 7
3. Electric Energy Measurement --------------------------------------------- 7
4. PC Communication Method ----------------------------------------------- 9
5. Functions of “Hold” and the Backlight ------------------------------- 10
6. Others ---------------------------------------------------------------------------- 10

- 3 -
Input Value Limit
Function Maximum Input and Time
1. Product Introduction
Wattman (HPM-100A)isaconsumption/standby powe analyze and a p actical and economical handheld-type wattmete . It
enables the measu ement of the powe consumption of home appliances and business equipment with not g eate than a
9mW~3.75kW powe consumption, in a Plug & Play way, thus allowing easy and simple ope ation by any use . It also
enables the easy conve sion of elect ic powe usage data into elect ic cha ge and amount of CO2 emission values.
⊙ Characteristics
- It displays the voltage, cu ent, powe , and f equency at the same time. It can also display the powe
facto ,
elect ic ene gy, elect ic cha ge, and amount of CO2 emission based on the amount of elect ic ene gy used.
- The e is no need fo batte ies and adapto s as no additional powe ope ation is needed.
- Supe io p ecision, with a base e o ange of ±0.4%.
- Equipped with unive sal and convenient multiplug sockets.
- Its f ont buttons enable the selection of the unit to be used fo the elect ic cha ge and the amount of CO2 emission.
- Equipped with a time setting function (00.h : unlimited; 1~24 h ).
- Comes with a f ee copy of the GUI PC p og am.
- With f ee po table bags.
- Cable supply fo data communication use (with cha ge).
Warning
- Ext eme caution against high voltage should be taken whenusingthisp oduct.
- The inapp op iate use of this p oduct may cause casualties o elect ic shock.
- Obse ve all the safety guidelines stated in the accompanying manual.
- Do not epai you own unit unless you have the necessa y skills.
⊙ Safety Instructions
This equipment was designed in acco dance with the CE CAT II & FCC safety standa ds. The use s, howeve , must
have a tho ough knowledge of the following guidelines and must use the p oduct with full attention to ensu e
safe
ope ation.
- Do not attempt to ope ate the p oduct if you cannot close its back cove .

- 4 -
Voltage AC 90V ~ 260V
Cu ent
Within an AC 10~15A ange, the e should be at-least-10-minute
inte vals
and each measu ement should be done within 30 seconds. With
a
less-than-10A cu ent, the measu ements can be conducted fo a
longe
time.
※ When measuring a continuous 10 or higher current, thebuilt-infuse can be disconnected. The measurement should
thus be accomplished within a maximum of 30 seconds.
※ Also, make su e that the supply voltage (sou ce voltage) and the voltage ating of the equipment to be measu ed a e
identical.
⊙ General Characteristics
- It is easy to analyze the voltage, elect ic cu ent, and f equency values obtained as they a e displayed at the same
time.
- ±0.4% elect ic powe accu acy.
- ±0.3% voltage and elect ic cu ent accu acy.
- Voltage measu ement ange: AC 90~260V (±0.3%, ±3 digit)
- Elect ic cu ent measu ement ange: AC 100μA~15A (±0.3%, ±3 digit)
- Elect ic powe measu ement ange: 9mW~3.75kW (±0.4%, ±3 digit)
- Powe facto measu ement ange: ±0.001~1.000 (±0.5%, ±3 digit)
- F equency measu ement ange: 50~1000Hz (±0.3%, ±3 digit)
- Ope ating tempe atu e: 0~50°C
- Sto ing tempe atu e: -20~60°C; humidity: 0~80%
- Tempe atu e coefficient: 0.1 * (stated accu acy) / 1°C (not g eate than 18°C, o 28°C o above)
- Altitude: 2000 m (6,561.7 feet)
- Size: 115 mm(W) x 200 mm(H) x 45 mm(D)
- Weight: 650 g

- 5 -
Push Button Function
LIGHT LCD backlight on/off
HOLD Tempo a ily pauses the measu ement value
Wh.CLR
In the accumulative elect ic ene gy mode (Wh), with no accumulation being ope ated,
p ess
this button fo 3 seconds and it will be eset when you hea the beeping sound.
It is used to delete the elect ic ene gy value p eviously obtained and to conduct a
new
measu ement.
DISPLAY
Voltage (W), accumulative elect ic ene gy (Wh), powe facto (PF), amount of
CO2
emission(kg), and elect ic cha ge mode conve sion button.
Wh
TIME SET Time setting fo elect ic ene gy (Wh) accumulation (00.h : unlimited, 1~24 h )
Wh
RUN/STOP
Sta t/stop accumulation setting in the accumulative elect ic ene gy mode
(At the sta t of the accumulation, “ENERGY” will be displayed on the LCD sc een.)
COST
SET
Unit setting of the elect ic cha ge and the amount of CO2 emission
Figu e 1. F ont view and button of
HPM-100A
⊙ Function of the Push Buttons

- 6 -
※ Warning: ll the electric-energy-related buttons (Wh CLR, Wh TIME SET, Wh RUN/STOP, COST SET) can be
operated in the accumulated electric energy mode (Wh).
⊙ LCD Display
1. Input C : Wattman is for C use only.
2. Temporary Pause : Use when pausing the measurement value.
3. Communication Display : "On" when using RS-232C communication.
4. ccumulation Display : "On" when accumulating electric energy.
5. Frequency : Frequency measurement unit.
6. mount of Co2 Emission : Display the amount of Co2 emission per kWh.
7. Yen(Japanese currency unit) : For Japan's use.
8. Euro(European currency unit) : For European Union member's use.
9. Yuan(Chinese currency unit) : For Chinese's use.
10. Dollar(U.S. currency unit) : For merican's use.
11. Won(Korean currency unit) : For Korean's use.
12. Power Factor : Displays the power factor of the equipment to be measured
13. Electric Power : Displays the electric power consumption of the equipment to be measured.
14. Electric Energy(per hour) : Displays the electric energy of the equipment to be measured.
15. Measured Voltage : Displays the service voltage of the equipment to be measured.
16. Measured Electric Current : Displays the working voltage of the equipment to be measured.
Initial (Default) Settings
The initial settings a e 0.000V, 00.00mA, 0.000W, and 00.00Hz, with AUTO Range on display.

- 7 -
2. Electric Power Measurement
Fi st, make su e that the supply voltage (sou ce voltage) and the voltage ating of the equipment to be measu ed a e
identical.
Wattman enables the simultaneous measu ement of the voltage, elect ic cu ent, elect ic powe , and f equency values.
It basically enables the measu ement of a 9mW~3.75kW ange (consumption and standby powe measu ement).
1. When the powe is on, the voltage, elect ic cu ent, elect ic powe , and f equency values will be displayed on the
LCD sc een.
2. When measu ing, connect the measu ement load to the f ont plug socket of Wattman.
3. When the DISPLAY button is p essed, conve sion will be accomplished in the following o de :
elect ic powe → elect ic ene gy → powe facto → amount of CO2emission→elect ic cha ge.
4. When measu ing fo a long time (mo e than 1 hou ), set at a maximum of 10A.
3. Electric Energy Measurement
Elect ic ene gy measu ement will be conducted up to 2000 kWh.
Ex) Fo the instantaneous powe of 1 KW, it is 2000 hou s.
1. DISPLAY P ess the button to set the accumulative elect ic ene gy mode
2. P ess the
Wh
TIME SET and buttons to set the desi ed accumulation time (1~24 h ). If the time does not
change,
Wh.CLR eset afte the initialization.
3. P ess the
Wh
RUN/STOP button and “ENERGY” will be displayed on the sc een and the accumulation will sta t.
4. Othe measu ement values can be checked du ing the accumulation.
5. When the accumulation stops, p ess the
Wh
RUN/STOP button.
6. When deleting the p eviously accumulated elect ic ene gy value, p ess the Wh.CLR button fo 3 seconds. It will be
eset afte the light of “Cl ” is on.
⊙ Time Setting: 1~24 hr
Wattman enables measu ement afte setting the time fo elect ic ene gy value accumulation (00.h : unlimited, 1~24 h ).
1. When setting the time, the p eviously accumulated value will be eset. P ess the DISPLAY button to conve t to the
accumulative elect ic ene gy mode, then p ess Wh.CLR fo 3 seconds to eset it.

- 8 -
2. P ess the
Wh
TIME SET button fo accumulation time setting f om 1 h up to 24 h (00.h : unlimited accumulation).
3. P ess the
Wh
RUN/STOP button and the accumulation will be conducted fo the du ation of the set time.
4. While accumulation is in p og ess, p essing the
Wh
RUN/STOP button will stop the accumulation p ocess. When the same
button is p essed again, the accumulation will continue.
5. While accumulation is in p og ess, the emaining time will be displayed on the sc een, with a countdown f om the
set time.
6. To check the set time, p ess the
Wh
TIME SET button and the set time will be b iefly displayed.
⊙ Electric Charge and CO2 Emission mount Setting
Wattman enables the accumulated elect ic ene gy to be conve ted into its co esponding elect ic cha ge
and
CO2 emission amount values, and to be displayed on the sc een.
The elect ic cha ge and CO2emissionamountpe kWhappliedcanbemodified,ifnecessa y.
① Electric Charge Measurement
Please note that the ave age elect ic cha ge of an ave age household (with an elect ic powe usage ate of
300
kWh/month) is KRW168/kWh.
Ex. Elect ic cha ge (KRW ￦) = 1 kWh × 168 (￦)
* The electric charge unit can be modified using the “Setting” key.
② CO2 Emission mount Measurement
The allowable amount of fossil fuel (pet oleum, coal) CO2 emission fo 1kWh powe gene ation is 0.424kg (acco ding to
the 2005 esea ch data obtained by Ko ea Institute of Ene gy).
Ex. Amount of CO2emission(Kg) = 1 kWh × 0.424 kg
※ As the bases of the CO2 emission amounts a e diffe ent, modification can be done using the “Setting” key.
③ How to Set
1. When “COST SET” is p essed, the p eviously set value will be displayed with a unit on the sc een.
2. The up (▲), down (▼), left (◀), and ente (⤶) buttons can be used fo the co esponding functions.
3. The value can be modified using the up (▲), down (▼), o left (◀) buttons.
4. P ess “Ente (⤶)” to save the setting. The unit setting can be modified in the same way.
When all the modifications have been done, p ess “COST SET” to finalize the changes made.

- 9 -
4. PC Communication Method
1. HPM-100A is compatible with RS-232C communication.
2. The GUI PC p og am will be p ovided f ee of cha ge. It can also be downloaded f om the homepage.
3. The basic t ansmission p otocol is as follows: (T ansmission p otocols can be confi med f om a hype te minal.)
- Cable supply fo data communication (with cha ge)
(1) Communication Po t: Connect to a c eated po t in the case of a se ial communication po t o a USB cable.
(2) T ansmission Speed: 9600
(3) Pa ity: none
(4) Stop Bit: 1
(5) Flow Cont ol: none
(6) When the English capital lette “S” is t ansmitted f om a PC o Micom, o when “RS-232” is p essed, data will
be consecutively eceived and “COMM” will be displayed on the p oduct’s sc een. When the English capital lette
“E” is t ansmitted, the communication will be cancelled.
“S” on the communication sc een means the sta t of a set of data, while “E” means the end.
※ Wa ning: When collecting data th ough the HPM-100A GUI p og am, the accumulated Wh value on HPM-100A will
be eset.
* Received data ( : indicates a decimal point)
Ex) Data obtained: 220.0V, 100.0mA, 22.00W, 120.3Wh, 1.000PF, 60.00Hz
① P ess the “S” t ansmission on the PC, o the “RS232” button.
② The data obtained will be consecutively eceived in the fo mat shown below.
③ When the English capital lette “E” is t ansmitted, the communication will be cancelled
S 22003Vo 10003 m 22002Wa 10001Pf 60001Hz 11kg 5371Wo E

- 10 -
UNIT(data at the decimal point)
UNIT 1 UNIT 2 UNIT 3 UNIT 4 UNIT 5 UNIT 6 UNIT 7
Volt 0.000 V 00.00 V 000.0 V - - - -
Ampere 0.000 mA 00.00 mA 000.0mA 0.000A 00.00A 000.0A -
Watt 0.000 W 00.00 W 000.0 W 0.000 kW 00.00 kW 000.0 kW
Wh 0.000 Wh 00.00 Wh 000.0 Wh 0.000 kWh 00.00 kWh 000.0 kWh 0000 kWh
PF 0.000 PF - - - - - -
VAR 0.000 Var - - - - - -
Hz 00.00 Hz 000.0 Hz 0.000 kHz - - - -
￦ 0.000 ￦ 00.00 ￦ 000.0 ￦ 0000 ￦ - - -
$ 0.000 $ 00.00 $ 000.0 $ 0000 $ - - -
￥ 0.000 ￥ 00.00 ￥ 000.0 ￥ 0000 ￥ - - -
€0.000 €00.00 €000.0 €0000 €- - -
元0.000 元00.00 元000.0 元0000 元- - -
kg 0.000 kg 00.00 kg 000.0 kg 0000 kg - - -
5. Functions of “Hold” and the Backlight
P ess “HOLD” to tempo a ily pause the displayed value. All actions will be suspended until “HOLD” is p essed again.
To ope ate the LCD backlight, p ess LIGHT .
* The powe consumption of the backlight is not included in the measu ed value.
6. Others
Maintenance
Warning
To p event elect ic shock o damage, take note of the following:
1. Do not sepa ate the equipment f om its case when the powe sou ce is applied.
2. Use an identical voltage ating (250V, 15A) when eplacing a fuse damaged due to ove load.
3. Close the case only afte ensu ing that the fuse has been p ope ly eplaced and that the wi ing is
p ope ly
a anged.
4. Do not open the case except when eplacing a fuse.
5. When othe maintenance is equi ed, consult with the company’s A/S se vice team.
The company shall not be liable fo any damage incu ed by the p oduct due to the epai s conducted by
the
use s themselves o by non-company pe sonnel, othe than eplacing a fuse.

- 11 -
When a problem arises:
1. Please efe to the manual.
2. When a measu ement load is connected to the plug socket of the p oduct, the p oduct can malfunction due to the
exte nal powe su ge. In this case, emove the powe plug of the measu ing equipment, then esupply powe afte
3 seconds.
3. Se vices will be p ovided f ee of cha ge within a yea f om the date of pu chase of the p oduct. Howeve , when
p oduct failu e occu s even du ing the wa anty pe iod due to the custome ’s negligence o due to a
natu al
disaste , ext a cha ges will be applied fo the se vices ende ed by the company’s A/S se vice team.
4. It is much safe to have the p oduct epai ed by the company’s se vice pe sonnel even beyond the wa anty pe iod.
(A/S Se vice Cente Contact No.:82-32-234-3794)
ccessories: Manual fo use s, po table bag, cable supply fo data communication use (with cha ge)
AD Powe Co., Ltd.
Gyeonggi-do Bucheon-si Wonmi-gu Yakdae-dong 193
High-Tech Measu ing Device Resea ch Complex 402, Room 1304
E-mail: adc@adpowe 21.com
Tel: [phone]~6
A/S Se vice Cente : 82-32-234-3794
Fax: [phone]
Homepage: www.adpowe 21.com
Please type “Wattman” on the add ess tab.