Siemens SITRANS F M MAGFLO User manual

Order no.: FDK-521H1191
SFIDK.PS.026.E5.02
SITRANS F M MAGFLO®®
®®
®
Electromagnetic flowmeters
Transmitter type MAG 6000 Industry & MAG 6000 Industry (Ex d)
sensor type MAG 1100/MAG 1100 FOOD/MAG 1100 Ex &
MAG 5100 W/MAG 3100/MAG 3100 Ex
[]
*083R9176*
Operating Manual
s
Technical Documentation (handbooks, instructions, manuals etc.) on the complete product
range SITRANS F can be found on the internet/intranet on the following links:
English: http://www4.ad.siemens.de/WW/view/en/10806951/133300

SITRANS F M MAGFLO®®
®®
®
2SFIDK.PS.026.E5.02
ENGLISH
Contents 1. Introduction ................................................................................................................... 3
2. Installation ..................................................................................................................... 4
2.1 Installation of transmitter ............................................................................................... 4
2.2 Installation of sensor ..................................................................................................... 4
2.3.1 Remote installation - At the sensor ............................................................................... 6
2.3.2 Remote installation - Transmitter .................................................................................. 6
2.4 Ex survey according to Directive 94/9/EC (ATEX) ........................................................ 7
2.5 Overview and intrinsically safe data ............................................................................. 8
2.5.1 Transmitter data MAG 6000 I (Ex d) .............................................................................. 8
2.6 Device identification ..................................................................................................... 9
2.7 Ex approvals ............................................................................................................... 10
3. Electrical connection ................................................................................................... 12
3.1 Transmitter type MAG 6000 I ...................................................................................... 11
3.2 Installation examples .................................................................................................. 13
3.2.1 Add-on communication module ................................................................................. 14
4. Technical data ............................................................................................................. 15
4.1.1 Dimensions and weight MAG 1100 standard & Ex, MAG 1100 FOOD ...................... 16
4.1.2 Sensor MAG 1100 Ex ................................................................................................. 17
4.2.1 Dimensions and weight MAG 3100 Ex ....................................................................... 18
4.2.2 Sensor MAG 3100 Ex ................................................................................................. 19
4.2.3 Dimensions and weight MAG 5100 W ........................................................................ 20
4.2.4 Sensor MAG 5100 W .................................................................................................. 21
4.3 Transmitter type MAG 6000 I ....................................................................................... 22
4.4 Output characteris-tics MAG 6000 I ............................................................................ 23
5. Commissioning ........................................................................................................... 24
5.1 Keypad and display layout ......................................................................................... 24
5.2 Menu build-up ............................................................................................................. 25
5.2.1 Password .................................................................................................................... 25
5.3 MAG 6000 I ................................................................................................................. 26
5.4 Basic settings .............................................................................................................. 27
5.4.1 Outputs ........................................................................................................................ 28
5.4.2 Digital and relay outputs ............................................................................................. 29
5.4.3 Relay outputs ..............................................................................................................29
5.4.4 External input .............................................................................................................. 29
5.4.5 Sensor characteristics ................................................................................................ 30
5.4.6 Reset mode .................................................................................................................30
5.4.7 Service mode .............................................................................................................. 31
5.4.8 Operator menu setup .................................................................................................. 32
5.4.9 Product identity ...........................................................................................................33
5.4.10 Change password ...................................................................................................... 33
5.4.11 Language mode ......................................................................................................... 34
5.4.12 HART®communication .............................................................................................. 34
5.5.1 Dimension dependent factory settings ....................................................................... 37
5.5.2 Dimension dependent batch and pulse output settings ............................................. 37
5.6 Flow rate ..................................................................................................................... 37
5.6.1 Totalizer ....................................................................................................................... 37
5.6.2 Batch ........................................................................................................................... 37
5.6.3 List of error numbers ................................................................................................... 39
6. Service ........................................................................................................................ 39
6.1 Transmitter check list ................................................................................................... 39
6.2 Trouble shooting MAG transmitter .............................................................................. 40
6.3 Check list MAG sensor ................................................................................................ 41
6.4 Coil resistance ............................................................................................................ 43
7. Ordering ...................................................................................................................... 42
8. Certificates ..................................................................................................................43
8.1 EC-declaration of conformity ...................................................................................... 43
8.2 EC type examination certificate .................................................................................. 44

SITRANS F M MAGFLO®®
®®
®
3
SFIDK.PS.026.E5.02
ENGLISH
1. Introduction For safety reasons it is important that the following points, especially the points marked with a
warning sign, are read and understood before the system is being installed:
•Installation, connection, commissioning and service must be carried out by personnel
who are qualified and authorized to do so.
•It is very important that the same people have read and understand the instructions and
directions provided in this manual and that they follow the instructions and directions
before taking the equipment into use!
•People who are authorized and trained by the owner of the equipment may operate the
equipment.
•The installation must ensure that the measuring system is correctly connected and is in
accordance with the connection diagram.
•In applications with working pressures/media that can be dangerous to people, surroundings,
equipment or others in case of pipe fracture, we recommend that special precautions such
as special placement, shielding or installation of a security guard or a security valve should
be made when the sensor is being installed.
•Siemens Flow Instruments want to assist by estimating the chemical resistance of the sensor
parts that are in connection with the media, but it is at any time the customer’s responsibility,
which materials are chosen and Siemens Flow Instruments takes no responsibility if the
sensor corrodes!
•Equipment used in hazardous areas must be Ex-approved and marked for Europe and
UL for USA.
It is required that the special directions provided in the manual and in the Ex certificate must
be followed!
•Installation of the equipment must comply with national regulations.
Example EN 60079-14 for Denmark.
•Repair and service must be done by approved Siemens Flow Instruments personnel only.
1. Introduction

SITRANS F M MAGFLO®®
®®
®
4SFIDK.PS.026.E5.02
ENGLISH
2. Installation
2. Installation
Category 2 equipment
In addition to the sensor, the MAG 6000 I as
remote or compact mounted may be installed in
Ex zone 1 and zone 2.
2.2 Installation of sensor
Installation of transmitter can be remote or
compact mounted.
2.1 Installation of
transmitter
Hazardous area
The sensor must always be completely full with
liquid.
Therefore avoid:
•Installation at the highest point in the pipe
system
•Installation in vertical pipes with free outlet
For partially filled pipes or pipes with down-
ward flow and free outlet the flowmeter should
be located in a U-tube.
Installation in vertical pipes
Recommended flow direction: upwards. This
minimizes the effect on the measurement of
any gas/air bubbles in the liquid.

SITRANS F M MAGFLO®®
®®
®
5
SFIDK.PS.026.E5.02
ENGLISH
Installation in horizontal pipes
The sensor must be mounted as shown in the
upper figure. Do not mount the sensor as shown
in the lower figure. This will position the elec-
trodes at the top where there is possibility for air
bubbles and at the bottom where there is pos-
sibility for mud, sludge, sand etc.
If using empty pipe detection the sensor can be
tilted 45°, as shown in the upper figure.
Measuring abrasive liquids and liquids con-
taining particles
Recommended installation is in a vertical/in-
clined pipe to minimize the wear and deposits
in the sensor.
Inlet and outlet conditions
To achieve accurate flow measurement it is
essential to have straight lengths of inlet and
outlet pipes and a certain distance between
pumps and valves.
It is also important to centre the flowmeter in
relation to pipe flanges and gaskets.
2.2 Installation of sensor
(continued)
Installation in large pipes
The flowmeter can be installed between two
reducers (e.g. DIN 28545). Assuming that at 8°
the following pressure drop curve applies. The
curves are applicable to water.
Example:
A flow velocity of 3 m/s (V) in a sensor with a
diameter reduction from DN 100 to DN 80
(d1/d2= 0.8) gives a pressure drop of 2.9 mbar.
2. Installation

SITRANS F M MAGFLO®®
®®
®
6SFIDK.PS.026.E5.02
ENGLISH
2.3.1 Remote installation -
At the sensor
Fit and connect the electrode and coil cables
as shown in “Electrical connections”.
The unscreened cable ends must be kept as
short as possible.
The electrode cable and the coil cable must be
kept separate to prevent interference.
Tighten the cable glands well to obtain opti-
mum sealing.
Remove the SENSORPROM®unit from the
sensor and mount it in the terminal block in the
transmitter.
2.3.2 Remote installation -
Transmitter
No power up with open lid -
Do not open lid while power
on
Fit the SENSORPROM®memory unit in the transmitter.
The SENSORPROM®unit is supplied with the sensor in the terminal box.
2. Installation

SITRANS F M MAGFLO®®
®®
®
7
SFIDK.PS.026.E5.02
ENGLISH
2.4 Ex survey according
to Directive 94/9/EC
(ATEX)
Applies to instruments used in underground mining
operations, as well as their above ground
operations, which can be endangered by mine gas
and/or flammable dusts.
Instrument groups
Applies to instruments used in the remaining areas
which can be endangered by a potentially explosive
atmosphere.
Instruments of this category are for use in
areas where ignitable atmospheres, caused by
a mixture of air and gasses, vapours or mists or
by dust/air mixtures, can exist all of the time or
for long periods of time or else frequently.
Instruments of this category are for use in
areas where ignitable atmospheres caused, by
a mixture of air and gasses, vapours or mists or
by dust/air mixtures, can exist some of the time.
Instruments of this category are for use in
areas where ignitable atmospheres, caused by
a mixture of air and gasses, vapours or mists or
by dust/air mixtures, are not likely to exist.
However, if they do occur then in all probability,
only seldom or for short periods of time.
Instrument category
(The figures in brackets refer to IEC)
Built according to European norm = E
Explosion protected electrial equipment = Ex
Ex protection labelling in square brackets refers to "Associated electrical equipment"
as an example : II 2G E Ex d IIB T3-T6
Type of protection
o Oil encapsulated i Intrinsic safety (ia, ib)
p Pressurized apparatus n Non-incentive equipment
q Powder filling m Encapsulation
dFlameproof enclosure s Special protection
e Increased safety
Explosion groups
Gases and vapours Minimum EN/
(examples) ignition IEC
energy [mJ]
•Ammonia - IIA
•Acetone, aircraft fuel, benzine,
crude oil, diesel oil, ethane, ethanoic
acid, ether, gasolines, heating oil,
hexane, methane, propane 0.18 IIA
•Ethylene, isoprene, town gas 0.06 IIB
•Acetylene, carbon disulphide,
hydrogen 0.02 IIC
Ignition temperature
Maximum surface temperature EN / IEC
450°C 842°FT1
300°C 572°FT2
200°C 392°FT3
135°C 275°FT4
100°C 212°FT5
85°C 185°FT6
I
II
EN 50014 Directive 94/9/EC (ATEX)
Definition
1G
(0)
Labelling
with gases
Labelling
with dusts
1D
(20)
2G
(1)
2D
(21)
3G
(2)
3D
(22)
2. Installation

SITRANS F M MAGFLO®®
®®
®
8SFIDK.PS.026.E5.02
ENGLISH
2.5 Overview and
intrinsically safe data
Specifications:
Supply: 115-230 V or 24 V
Ambient temperature: −20 to 60°C
Enclosure: IP67/NEMA 4X
2. Installation
SENSOR INTERFACE
1. DN 6 - DN 300 mm
Certificate: Sira 03ATEX1503X
II 2(1)(2) G D
Remote version: EEx d [ia] ia [ib] ib IIB T6 / Compact version: EEx d [ia] [ib] IIB T6
2.5.1 Transmitter data
MAG 6000 I (Ex d)
Electrode
81,82,83,84
IIB IIC
Uo30 V 30 V
Io6.1 mA 6.1 mA
Co66 nF 560 nF
Lo0.96 H 0.96 H
Po45.5 mW 45.5 mW
! Coil terminal 85, 86 are “e” terminals.
2. DN 350 - 2000 mm
Certificate: Sira 05ATEX2072X
II 2(1)(2) G D
Remote version: EEx d e [ia] ia [ib] ib IIC T6 / Compact version: EEx d [ia] [ib] IIC T6
User I/O INTERFACE
DN 6 - DN 300
Certificate: Sira 03ATEX1503X
II 2(1)(2) G D
Remote version: EEx d [ia] ia [ib] ib IIB T6 / Compact version: EEx d [ia] [ib] IIB T6
DN 350 - DN 2000
Certificate: Sira 05ATEX2072X
II 2(1)(2) G D
Remote version: EEx d e [ia] ia [ib] ib IIC T6 / Compact version: EEx d [ia] [ib] IIC T6
Electrode Coil
81,82,83,84 85,86
IIB IIC* IIB IIC*
Uo30 V Uo30 V
Io6.1 mA Io105 mA
Co560 nF Co60 nF
Lo1 H Lo2.07 mH
Po45.5 mW Po3.3 W
* N/A

SITRANS F M MAGFLO®®
®®
®
9
SFIDK.PS.026.E5.02
ENGLISH
Current (31-32) Relay (44,45,46) Freq./pulse (56,57) Profi (95, 96) (FISCO) Dig. Input (77,78)
Passive IIB/IIC IIB/IIC IIB/IIC IIB/IIC IIB/IIC
Ui30 V Ui30 V Ui28 V Ui17.5 V Ui30 V
Ii100 mA Ii200 mA Ii100 mA Ii380 mA Ii
Ci16.5 nF Ci0C
i12 nF Ci0C i0
Li36 µH Li0L
i36 µH Li0L i0
Pi5.32 W Pi
Active IIB IIC
Uo30 V 30 V
Io87.8 mA 87.8 mA
Co560 nF 66 nF
Lo18.41 mH 4.57 mH
Po0.66 W 0.66 W
2.6 Device identification
Example label, sensor
remote MAG 3100 Ex
Category 2 equipment
Sensors may be installed in zone 1 and zone 2.
Sensors intrinsically safe data
See table below.
MAG 1100 & MAG 3100
EEx ia IIB T3...T6
Terminals 85-86 82-83
MAG sensor coil electrode
Ui28 V 30 V
Ii140 mA 50 mA
Pi2 W 0.5 W
Li2 mH 20 µH
Ci50 nF 50 nF
MAG 1100 DN 6 - 100
MAG 3100 DN 15 - 300 Ex ib
Terminals 85-86 82-83
MAG sensor coil electrode
Ui-
Ii- 50 mA
Pi- 0.5 W
Li-
Ci- 50 nF
MAG 3100 DN 350 - 2000 Ex e ia
IS data sensor
Terminals 85-86 82-83
MAG sensors Coil circuit "ib" Electrode
circuit "ia"
Ui30 V 30 V
Ii140 mA 50 mA
Pi2 W 0.5 W
Li2 mH 20 µH
Ci50 nF 50 nF
All MAG 1100 Ex and MAG 3100 Ex sensors
have the following ratings and input parameters:

SITRANS F M MAGFLO®®
®®
®
10 SFIDK.PS.026.E5.02
ENGLISH
Example label, transmitter
type MAG 6000 I (Ex d)
compact
2. Installation
Data not for reference
2.7 Ex approvals MAG 1100 Ex
DN 6 - DN 100
SIRA 03 ATEX 1423X CE 0518
II 2 (1)(2) G
EEx [ia] [ib] IIB T4...T6,
Temperature ratings are as follows*:
T4 (max. surface < 135°C) for liquid temperatures lower than 100°C
T5 (max. surface < 100°C) for liquid temperatures lower than 82°C
T6 (max. surface < 85°C) for liquid temperatures lower than 67°C
For an ambient temperature of –20°C to + 50°C
MAG 3100 Ex
DN 15 - DN 300
SIRA 03 ATEX 1442X CE 0518
II 2 (1)(2) G
EEx d [ia] [ib] IIB T4...T6,
Temperature ratings are as follows*:
T4 (max. surface < 135°C) for liquid temperatures lower than 100°C
T5 (max. surface < 100°C) for liquid temperatures lower than 87°C
T6 (max. surface < 85°C) for liquid temperatures lower than 72°C
For an ambient temperature of –20°C to +50°C
MAG 3100 Ex
DN 350 - DN 2000
SIRA 03 ATEX 3339X CE 0518
II 2 GD IP65 T(**) OC
EEx e ia IIC T3…T6,
where (**) represents the pipeline temperature + 5K for dust approval
Temperature ratings are as follows*:
T3 (max. surface < 200°C) for liquid temperatures lower than 190°C
T4 (max. surface < 135°C) for liquid temperatures lower than 125°C
T5 (max. surface < 100°C) for liquid temperatures lower than 90°C
T6 (max. surface < 85°C) for liquid temperatures lower than 75°C
For an ambient temperature of –20°C to +40°C
MAG 6000 I (Ex d)
For use with MAG 3100 Ex sizes DN 15 - DN 300
For use with MAG 1100 Ex (all sizes)
For compact and remote mounting DN 6 - DN 300:
SIRA 03 ATEX 1503X
II 2 (1) (2) G D
Remote version: EEx d [ia] ia [ib] ib IIB T6 / Compact version: EEx d [ia] [ib] IIB T6
For use with MAG 3100 Ex sizes DN 350 - DN 2000
SIRA 03 ATEX 2072X
II 2 (1) (2) G D
EEx d e [ia] ia [ib] ib IIC, T6
Remote version: EEx d e [ia] ia [ib] ib IIC T6 / Compact version: EEx d [ia] [ib] IIC T6
* Temperature ratings may be limited by the lining selected, see section 4.

SITRANS F M MAGFLO®®
®®
®
11
SFIDK.PS.026.E5.02
ENGLISH
3.1 Transmitter type
MAG 6000 I
3. Electrical connection
Potential Hazards
Grounding
The mains protective earth wire must be connected to the PE terminal in accordance
with the diagram (class 1 power supply).
For Ex intrinsically safe
specifications, refer to
section 2.5

SITRANS F M MAGFLO®®
®®
®
12 SFIDK.PS.026.E5.02
ENGLISH
Installation 1) Mains supply 115 to 230 V AC from building installation Class II. A switch or circuit-breaker
(max. 15 A) shall be included in the building installation. It must be in close proximity to the
equipment and within easy reach of the OPERATOR, and it shall be marked as the
disconnecting device for the equipment.
2) The mains protective earth wire must be connected to the PE terminal, if the earth
wire is not connected, personnel can be exposed to 115V/230V.
Required cable min. AGW16 or 1.5 Cu wire.
For field wiring installation National Installation Code shall be met of the country, where the
flowmeters are installed.
Main voltage terminals must be out of reach for OPERATOR to avoid any hazards!
Intrinsically safe terminals!
It is an absolute requirement that the wires/terminals of the intrinsically safe circuits cannot get
into contact with the wires of the other cables. The distance between cables/wires therefore must
be at least 50 mm or otherwise protected.
It is recommended to fasten the cables/wires in a way that they, even in case of an error, cannot
get into contact with each other. Make the wire ends as short as possible.
Digital output
If the internal resistance of the loads exceeds 10KΩ, it is recommended to connect an external
1-10 KΩload resistor in parallel to the load.
3. Electrical connection
When reassembling the unit, make sure that the 2 screws are properly tightened in order to ensure
a correct assembly and a proper ground connection.
Cover/insulate the power supply terminals with the plastic cover (to secure sufficient insulation).
TORX 20

SITRANS F M MAGFLO®®
®®
®
13
SFIDK.PS.026.E5.02
ENGLISH
At the MAG 6000 I the current output terminal 31, 32 can be switch between active mode
(transmitter powered) to passive mode default (external powered).
3.2 Installation examples
Current output in passive
mode
Frequency/pulse output in
passive mode
Active/passive current
output
3. Electrical connection
Passive A = Active
(fatory default MAG 6000 I)
Passive B = Passive
(fatory default MAG 6000 I) (Ex d)

SITRANS F M MAGFLO®®
®®
®
14 SFIDK.PS.026.E5.02
ENGLISH
3.2.1 Add-on
communication
module
3. Unpack the module and fit into module
holder.
4. Press the add-on module in the direction
shown, until it stops and is firmly seated in
position.
5. Re-insert the complete transmitter module
in reverse order.
1. Open transmitter.
2. Remove electronic insert.
3. Electrical connection

SITRANS F M MAGFLO®®
®®
®
15
SFIDK.PS.026.E5.02
ENGLISH
4. Technical data
4.1.1 Dimensions and
weight
MAG 1100 standard
& Ex
MAG 1100/6000 I compact/separate
4. Technical data
Transmitter to be supported to avoid tension on sensor part.
1) 13 mm shorter when the AISI terminal box is used (Ex & high temperature 200 °C)
2) Ex version 8 mm higher
3) With transmitter type MAG 6000 I installed, weight is increased by approx. 5.5 kg
DN A1) A12) B1) B12) DD
iDiDpDGWeight 3)
Ceramic (PFA)
[mm] [mm] [mm] [mm] [mm] [mm] [mm] [mm] [mm] [kg]
2 161 312 186 336 48.3 2 N/A 17.3 34 2.2
3 161 312 186 336 48.3 3 N/A 17.3 34 2.2
6 161 312 186 336 48.3 6 N/A 17.3 34 2.2
10 161 312 186 336 48.3 10 10 17.3 34 2.2
15 161 312 186 336 48.3 15 16 17.3 40 2.2
25 169 319 201 351 63.4 25 26 28.5 56 2.7
40 181 329 223 371 84.0 40 38 43.4 75 3.4
50 189 338 240 389 101.6 50 50 54.5 90 4.2
65 199 347 259 407 120.0 65 66 62.5 112 5.5
80 205 354 271 420 133.0 80 81 82.5 124 7.0
100 218 367 297 446 159.0 100 100 107.1 150 10.0
PG 13.5

SITRANS F M MAGFLO®®
®®
®
16 SFIDK.PS.026.E5.02
ENGLISH
MAG 1100 FOOD MAG 1100 FOOD / 6000 I, compact and separate
1) Ex version 8 mm higher
2) With transmitter type MAG 6000 I installed, weight is increased by approx. 5.5 kg
DN L A A11)BB
11)D D iDiWeight 2)
(Al2O3) (PFA)
[mm] [mm] [mm] [mm] [mm] [mm] [mm] [mm] [kg]
10 64 156 303,7 181 335,7 64 10 10 2.2
15 64 156 303,7 181 335,7 64 15 16 2.2
25 79 164 312,2 196 350,9 77.5 25 26 2.7
40 94 176 325,9 218 371,4 91 40 38 3.4
50 104 184 329,5 235 389,0 119 50 50 4.2
65 131 194 342,4 254 407,4 130 65 66 5.5
80 156 200 342,9 266 420,4 155 80 81 7.0
100 186 213 354,9 292 446,4 183 100 100 10.0
4. Technical data
Transmitter to be supported to avoid tension on sensor part.
PG 13.5

SITRANS F M MAGFLO®®
®®
®
17
SFIDK.PS.026.E5.02
ENGLISH
Type Flangeless sensor (Wafer design)
Nominal size mm DN 6, 10, 15, 25, 40, 50, 65, 80, 100
Operating pressure DN 6 - DN 65: 40 bar, DN 80: 37.5 bar, DN 100: 30 bar
Vacuum: 1 ×10-6 bar
Temperature of medium
Ceramic −20°C to +100°C
Temperature shock (Duration > 1 min.):
(Ceramic liner) DN 6, 10, 15, 25: Max. ∆T ≤15°C/min.
DN 40, 50, 65: Max. ∆T ≤10°C/min.
DN 80, 100: Max. ∆T ≤5°C/min.
(Duration ≤1 min., followed by 10 min. rest):
DN 6, 10, 15, 25: Max. ∆T ≤80°C
DN 40, 50, 65: Max. ∆T ≤70°C
DN 80, 100: Max. ∆T ≤60°C
Ambient temperature Remote transmitter: −40°C to +100°C
Liner Aluminium oxide Al2O3(ceramics)
Electrodes Platinum with gold/titanium brazing alloy
Enclosure Stainless steel AISI 316 L (1.4404)
Terminal box Stainless steel AISI 316 (1.4436)
Fixing studs Stainless steel AISI 304 (1.4301)
Number and size to EN 1092-1:2001
Mating flanges EN 1092-1:2001, ANSI B16.5 class 150 and 300 or equivalent
Gaskets Standard EPDM (max. 150°C, PN 40)
Option Graphite (max. 200°C, PN 40)
Option PTFE (max. 130°C, PN 25)
Cable entries 4 PG 13.5
Enclosure rating Standard IP67 to EN 60529 (NEMA 4X) (1 m w.g for 30 min.)
Option IP68 to EN 60529 (NEMA 6) (10 m w.g. cont.)
Mechanical load 18-1000 Hz random in all directions to EN 60068-2-36
(vibration) Sensor: 3.17 G/Compact Ex d: 1.14 G
Test pressure 80 bar (2 ×PN)
Ex approvals See section 2.7; Isinterface data see section 2.5
Excitation frequency DN 6 - 65: 6.25 Hz
DN 80 - 100: 3.125 Hz
Conforms to PED, LVT, EMC PED - 97/23EC, LVD - 73/23 EEC +
amendment 93/68/EEC, EMC - 89/336 EEX
4.1.2 Sensor MAG 1100 Ex
4. Technical data

SITRANS F M MAGFLO®®
®®
®
18 SFIDK.PS.026.E5.02
ENGLISH
DN A1) A1BD
1L2) AS TC 3) TE 3)
2129 E, AWWA
AS 4087 C-207
PN PN PN PN PN PN Class Class PN Class
6, 10 16 25 40 64 100 150 300 16-21- D
35
[mm] [mm] [mm] [mm] [mm] [mm] [mm] [mm] [mm] [mm] [mm] [mm] [mm] [mm] [mm] [mm] [mm] [kg]
15 199 338 59 104 200 200 200 200 - - 200 200 200 - 6 4
25 199 338 59 104 200 200 200 200 - 260 200 200 200 1.2 6 5
40 209 348 82 124 200 200 200 200 - 280 270 270 200 1.2 6 8
50 217 356 72 139 200 200 200 200 276 300 270 270 200 1.2 6 9
65 224 363 72 154 200 200 200 200 320 350 280 280 200 1.2 6 11
80 234 373 72 174 200 200 272 272 323 340 290 290 2005) 1.2 6 12
100 254 393 85 214 250 250 250 250 380 400 250 310 250 1.2 6 16
125 267 406 85 239 250 250 250 250 420 450 250 335 250 1.2 6 19
150 288 427 85 282 300 300 300 300 415 450 300 300 300 1.2 6 27
200 316 455 137 338 350 350 350 350 480 530 350 350 350 1.2 8 40
250 344 483 137 393 450 450 450 450 550 620 450 450 450 1.2 8 60
300 369 508 137 444 500 500 500 500 600 680 500 500 500 1.6 8 80
350 362 513 270 462 550 550 550 550 700 800 550 550 550 - 1.6 8 110
400 387 538 270 512 600 600 600 600 750 - 600 600 600 - 1.6 10 125
450 418 569 310 563 600 600 600 600 - - 600 640 600 - 1.6 10 175
500 443 594 350 614 625 625 625 680 - - 680 730 625 - 1.6 10 200
600 494 645 430 715 750 750 750 750 - - 820 860 750 - 1.6 10 300
700 544 695 500 816 875 875 - - - - - - 875 875 2.0 - 350
750 571 722 556 869 - - - - - - - - 937 937 2.0 - 380
800 606 757 560 939 1000 1000 - - - - - - 1000 1000 2.0 - 475
900 653 804 630 1042 1125 1125 - - - - - - 1125 1125 2.0 - 560
1000 704 906 670 1146 1250 1250 - - - - - - 1250 1250 2.0 - 700
1100 755 906 770 1248 1375 1375 - - - - - - - - 2.0 - 1200
1200 810 961 792 1348 1500 1500 - - - - - - 1500 1500 2.0 - 1250
1400 925 1076 1000 1675 1750 1750 - - - - - - - - 3.0 - 1753
1500 972 1123 1020 1672 - - - - - - - - 1875 1875 3.0 - 2600
1600 1025 1176 1130 1915 2000 2000 - - - - - - - - 3.0 - 2341
1800 1123 1274 1250 1974 2250 2250 - - - - - - - - 3.0 - 3253
2000 1223 1374 1375 2174 2500 2500 - - - - - - - - 3.0 - 4060
4.2.1 Dimensions and
weight MAG 3100 Ex
MAG 3100 Ex
1) 13 mm shorter with AISI terminal box (Ex and high temperature)
2) When earthing flanges are used, the thickness of the earthing flange must be added to the built-in length
3)T
C= Type C grounding ring, TE= Type E grounding ring
4) Weights are approx. and for PN 16 without transmitter
5) PN 35 = 272
D = Outside diameter of flange, see flange tables
Weight 4)
EN 1092-1-2001 BS 1560/
ANSI 16.5
4. Technical data
PG 13.5

SITRANS F M MAGFLO®®
®®
®
19
SFIDK.PS.026.E5.02
ENGLISH
Type Sensor with flanges
Nominal size mm DN 15 - DN 2000
Temperature of medium1)Temperature classification
Liner: T3 + T4 T5 T6
Neoprene (standard) 0 to 70°C 0 to 70°C 0 to 70°C
EPDM2)−10 to 95°C−10 to 90°C−10-75°C
Linatex®rubber −20 to 70°C−20 to 70°C−20 to 70°C
Ebonite2)0 to 95°C 0 to 90°C 0 to 75°C
PTFE −20 to 100°C−20 to 90°C−20 to 75°C
Ambient temperature Remote transmitter: −20°C to 60°C
Operating pressure3) [[
[[
[abs.bar]]
]]
]
Liner:
Neoprene 0.01 to 100 bar
EPDM 0.01 to 40 bar
Linatex®0.01 to 40 bar
Ebonite 0.01 to 100 bar
PTFE teflon:
DN 15 to 600: 0.3 to 40 bar
Excitation frequency DN 15 - 65: 6.25 Hz
DN 80/100: 3.125 Hz
DN 125 - 300: 1.5625 Hz
DN 350 - 1200: 3.125 Hz
Enclosure rating Standard IP67 to EN 60529 (NEMA 4X) (1 m w.g for 30 min.)
Option IP68 to EN 60529 (NEMA 6) (10 m w.g. cont.)
Cable entries 4 Pg 13.5
Mechanical load 18-1000 Hz random, 3.17 G rms in all directions to EN 60068-2-36
Test pressure 1.5 ×PN
Flanges Standard DN 15-50: PN 40
EN 1092-1:20014)DN 65-150: PN 16
Rased face DN 200-1000: PN 10
DN 1100 -2000: PN 6
Option DN 65-1000: PN 6
DN 1200-2000: PN 10
DN 200-2000: PN 16
DN 200-600: PN 25
DN 65-600: PN 40
DN 50-400 PN 63
DN 25-350 PN 100
ANSI B 16.5 (∼BS 1560) 3/4"-24": Class 150 (20 bar)
3/4"-24": Class 300 (50 bar)
AS 2129 3/4"-48": Table D/E
AS 4087 PN 16 (DN 50 - 1200, 14 bar)
PN 21 (DN 50 - 600, 21 bar)
PN 35 (DN 50 - 600, 35 bar)
AWWA C-207 28"-78": Class D (10 bar)
Electrodes Standard AISI 316 Ti (1.4571)
Option Hastelloy C-276, Platinum / Iridium, Titanium, AISI 316 Ti Ceramic
Coated, Tantalum
PE - electrodes Standard As measuring electrodes (except PTFE)
Measuring pipe Standard AISI 304 (1.4301)
Option AISI 316 L (1.4404)
Flange and Standard Carbon steel
housing material Corrosion-resistant two-component coating (min. 150 µm)
Option AISI 304 (1.4301) flanges and carbon steel housing.
Coating as above
Option AISI 316 L (1.4404) flanges and housing
Ex-approval See section 2.7; Isinterface data see section 2.5
Conforms to PED, LVD, EMC PED - 97/23EC, LVD - 73/23 EEC +
amendment 93/68/EEC, EMC - 89/336 EEX
1) The maximum fluid temperature may be further limited by the approval temperature ratings, see section 2.7
2) With WRC (Water Research Council, UK) approval
3) Maximum operating pressure decreases with increasing operating temperature and with stainless steel flanges
4) EN 1092-1, DIN 2501 & BS 4504 have the same mating dimensions
4.2.2 Sensor MAG 3100 Ex
4. Technical data

SITRANS F M MAGFLO®®
®®
®
20 SFIDK.PS.026.E5.02
ENGLISH
MAG 5100 W, compact/separate
4.2.3 Dimensions and
weight MAG 5100 W
mm inch mm inch mm inch mm inch mm inch mm inch mm inch mm inch
25 1" 187 7.4 340 13.4 N/A N/A N/A N/A 200 7.9 200 7.9 N/A N/A
40 1½” 197 7.8 350 13.8 N/A N/A N/A N/A 200 7.9 200 7.9 N/A N/A
50 2" 188 7.4 341 13.4 N/A N/A 200 7.9 N/A N/A 200 7.9 N/A N/A
65 2½” 194 7.6 347 13.7 N/A N/A 200 7.9 N/A N/A 200 7.9 N/A N/A
80 3" 200 7.9 353 13.9 N/A N/A 200 7.9 N/A N/A 200 7.9 N/A N/A
100 4" 207 8.1 360 14.2 N/A N/A 250 9.8 N/A N/A 250 9.8 N/A N/A
125 5" 217 8.5 370 14.6 N/A N/A 250 9.8 N/A N/A 250 9.8 N/A N/A
150 6" 232 9.1 385 15.2 N/A N/A 300 11.8 N/A N/A 300 11.8 N/A N/A
200 8" 257 10.1 410 16.1 350 13.8 350 13.8 N/A N/A 350 13.8 N/A N/A
250 10" 284 11.2 437 17.2 450 17.7 450 17.7 N/A N/A 450 17.7 N/A N/A
300 12" 310 12.2 463 18.2 500 19.7 500 19.7 N/A N/A 500 19.7 N/A N/A
350 14" 362 14.3 515 20.3 550 21.7 550 21.7 N/A N/A 550 21.7 N/A N/A
400 16" 387 15.2 540 21.3 600 23.6 600 23.6 N/A N/A 600 23.6 N/A N/A
450 18" 418 16.5 571 22.5 600 23.6 600 23.6 N/A N/A 600 23.6 N/A N/A
500 20" 443 17.4 596 23.5 625 24.6 625 24.6 N/A N/A 680 26.8 N/A N/A
600 24" 494 19.4 647 25.5 750 29.5 750 29.5 N/A N/A 820 32.3 N/A N/A
700 28" 544 21.4 697 27.4 875 34.4 875 34.4 N/A N/A N/A N/A 875 34.4
750 30" 571 22.5 724 28.5 N/A N/A N/A N/A N/A N/A N/A N/A 937 36.9
800 32" 606 23.9 759 29.9 1000 39.4 1000 39.4 N/A N/A N/A N/A 1000 39.4
900 36" 653 25.7 806 31.7 1125 44.3 1125 44.3 N/A N/A N/A N/A 1125 44.3
1000 40" 704 27.7 857 33.7 1250 49.2 1250 49.2 N/A N/A N/A N/A 1250 49.2
42" 704 27.7 857 33.7 N/A N/A N/A N/A N/A N/A N/A N/A 1250 49.2
1100 44" 755 29.7 908 35.7 N/A N/A N/A N/A N/A N/A N/A N/A 1375 54.1
1200 48" 810 31.9 963 37.9 1500 59.1 1500 59.1 N/A N/A N/A N/A 1500 59.1
AWWA
Nominal
size
AL
PN 10 PN 16 PN 40 Class 150
4. Technical data
A1
PG 13.5 PG 13.5