ADTRAN Total Access 900 Series User manual

Technical Support 1-888-4ADTRAN (1-888-423-8726)
Configuring the
Total Access 900 Series
Web-Based GUI, AOS CLI,
and Connecting to the Unit
Quick Configuration Guide 61210916L1-42.1B March 2006
Web-Based GUI
The Web-based GUI is an online configuration tool that allows you to easily configure and view
the main settings, as well as the status of your system.
1. Connect the Total Access 900 Series unit to your network using the ETH 0/1 port on the rear
panel of the unit. The Total Access 900 Series units support auto MDI-MDIX crossover;
therefore, a straight-through cable can be used for this connection.
2. Configure your PC to obtain an IP address automatically (DCHP), or change the IP address
of your PC to 10.10.10.2. The default address for the Total Access 900 Series unit is
10.10.10.1.
3. Enter the IP address 10.10.10.1 (default) in your Internet browser Address field (see
example, below).
The configuration parameters used in the example outlined in this document are for
instructional purposes only. Please replace all example entries with your specific parameters
to configure your application.
Using the Web-Based GUI
Contact your network administrator if you need assistance changing your computer’s
IP settings.
If you cannot change the PC’s IP address, you will need to change the Total Access
900 Series IP address. For this procedure, see Connecting to the Total Access
900 Series on page 4.

2 Technical Support 1-888-4ADTRAN (1-888-423-8726) 61210916L1-42.1B
4. Once you are connected, you will be prompted to enter the user name and password.
Enter your User name (default is admin) and Password (default is password) and click OK.
5. The initial GUI screen appears.
While navigating the Web GUI, you will notice question mark symbols that
indicate additional information is available. Simply place your cursor over the symbol
to view the additional information.

61210916L1-42.1B Technical Support 1-888-4ADTRAN (1-888-423-8726) 3
Once you have logged in, click on Config Wizard to display the screen below. Use the buttons at
the bottom of the screen or the menu at the top left to navigate the Config Wizard.
Use the system’s Config Wizard utility as an online configuration tool to set up basic (as well as
advanced) voice applications. The Config Wizard can easily walk you through system setup,
voice and data settings, and trunk and station configuration through a series of easy to answer
questions. At the end of the wizard, you can review your choices and accept them or make
additional changes.
Using the Configuration Wizard
ADTRAN recommends using this wizard only for new installations. Some existing settings
may be lost or reset when using this wizard.

4 Technical Support 1-888-4ADTRAN (1-888-423-8726) 61210916L1-42.1B
Follow these steps if you are not able to change the PC’s IP address in order to access the Web
GUI. Change the Total Access 900 IP address to correspond with your network setup. See the
steps below for further instruction.
Connecting to the CRAFT Port
1. Connect a VT100 terminal (or PC with VT100 emulation software) to the Total Access 900
Series CRAFT port on the rear panel of your unit using a DB-9 (male) to DB-9 (female)
straight-through serial cable.
2. Insert the connector of the provided power cord into the power interface on the side panel of
the unit, and plug the cord into a standard electrical outlet.
3. Open a VT100 terminal session and configure the terminal’s COM port with the following
parameters:
Data Rate: 9600
Data Bits: 8
Parity Bits: None
Stop Bits: 1
Flow Control: None
4. Press the <Enter> key to activate the Adtran Operating System Command Line Interface
(AOS CLI). The AOS CLI allows you to access and control the system through a command-
driven CRAFT connection.
5. Enter enable at the > prompt, and enter the password when prompted. The default password
is password.
Changing the Total Access 900 Series IP Address
1. Enter config terminal to enter the Global Configuration mode.
2. Enter interface ethernet 0/1 to access the Ethernet interface.
3. Enter ip address 10.10.10.1 255.255.255.0 to assign an IP address to the Ethernet port
using a 24-bit subnet mask. Contact your Network Administrator to obtain the IP address
(and subnet mask) for your particular configuration.
4. Enter no shutdown to activate the interface to pass data.
5. Enter exit to exit the Ethernet interface commands and return to the Global Configuration
mode.
Saving the Configuration
1. Enter exit to return to the Enable command security mode.
2. At the #prompt, enter copy running-config startup-config to save the current configuration
to memory.
3. Enter exit to close the configuration session.
Connecting to the Total Access 900 Series
Return to Using the Web-Based GUI on page 1 (step 3) to connect to the
Total Access 900 Series Web-based GUI.