ADTRAN NETVANTA 3100 Series User manual

Quick Start Guide, 61700601G2-13E, March 2015 1
NETVANTA 3100 SERIES ROUTER
P/N 1700601G2, 1700611G2, 1700612G2
4 Copyright © 2015 ADTRAN, Inc. All Rights Reserved.
GETTING STARTED
Two configuration methods are available for your NetVanta unit:
• Web-based graphical user interface (GUI)
• ADTRAN Operating System (AOS) command line interface (CLI)
The GUI lets you configure the main unit settings, and provides online guidance, explanations for
each setting, and configuration wizards to help you get started. However, using the AOS CLI may
be necessary for more advanced configurations.
ACCESS THE GUI
You may access the GUI from any web browser on your network by following these steps:
1. Connect the router to your PC, using an Ethernet cable connected to one of the four ports on
the back of the unit (Ethernet 1,2,3, or 4).
2. Set your PC to a fixed IP address in the 10.10.10.0 /24 subnet. For example configure your
PC with the following settings:
IP Address: 10.10.10.2
Subnet Mask: 255.255.255.0
Neither a default gateway nor DNS server needs to be configured to connect to the unit. If
you cannot change your PC’s IP address, you will need to change the Unit’s IP address
using the CLI as explained in the section below.
3. Open a web browser and enter the unit’s IP address in your browser address line as follows:
http://10.10.10.1. The default IP address is 10.10.10.1, but if you had to change the unit’s IP
address using the CLI, enter that address in the browser line.
4. You will then be prompted for the user name and password (the default settings are admin
and password).
5. The initial GUI screen appears. You can access initial setup information by selecting Setup
Wizard from the menu on the left.
6. ADTRAN recommends changing the default password. Browse to System >Passwords. In
the Login Configuration section, enter a new Username and Password and select Apply
Changes.
CONFIGURE THE ATM PVC (NETVANTA 3130 ONLY)
1. Select the Getting Started link under the System menu. This brings up a side bar menu.
2. Select Step 1 - Configure the Public Interface at the top of the side bar menu to open the
ATM PVC menu.
3. Enter the PVC number and select an Interface Mode. Usually this is PPP or PPPoE;
however, if IP routing is chosen, you will need to enter an IP address.
By default, the NetVanta 3130 comes with an ADSL and an asynchronous
transfer mode (ATM) port already configured and enabled. The service
provider should provide a PVC (VPI/VCI) number, which will be used to
configure the ATM PVC.
CONFIGURE YOUR APPLICATION
The applications you will need to configure vary by product and by network. Review the list of
defaults for your unit before deciding what applications to configure. The following are some
common applications that should be configured on startup. These are all available online on
ADTRAN’s Support Community
NETVANTA 3100 SERIES DEFAULTS
Configuring Internet Access (Many to
one NAT) with the Firewall Wizard
in AOS
Configuring Port Forwarding in AOS
Configuring QoS for VOIP in AOS Configuring ADSL Internet Access in AOS
Configuring QoS in AOS Configuring DHCP Server in AOS
Configuring a VPN using Main Mode
in AOS
Configuring a VPN using Aggressive Mode
in AOS
Important: For additional details on product features, specifications,
installation, and safety, refer to the NetVanta 3100 Series Fixed Port
Routers Hardware Installation Guide available online at
https://supportforums.adtran.com.
Feature Default Value
IP Address 10.10.10.1
Username admin
Password password
HTTP Server Enabled
Event History On
IP Routing Enabled
DHCP Enabled
VLAN Interface Enabled (vlan 1) with IP address 10.10.10.1
Firewall Enabled
NAT Overload to eth 0/1 address (3120)
Overload to ppp 1 address (3130)

2 Support - Phone: [phone], Email: [email protected] Quick Start Guide, 61700601G2-13E, March 2015 3
4. Select Apply. If PPP or PPPoE is selected as the Interface Mode, you will be taken to the
PPP page after selecting Apply. Here you will need to select the type of authentication
needed, authentication passwords, and the Address Type. In most cases, you will want the
Address Type to be Negotiated. Select Apply when all the information is complete.
ACCESS THE CLI
If needed, you can access the CLI from a Telnet or SSH client. To access the CLI using a Telnet
or SSH client, follow these steps:
1. Connect the unit to your PC, using an Ethernet cable connected to one of the Ethernet ports
(Ethernet 1, 2, 3, or 4) on the rear of the unit.
2. Use a Telnet or SSH client to connect to 10.10.10.1. If you have changed your unit's IP
address, you will need to enter that address.
3. For SSH, log into the unit using the default login (admin) and password (password). For
Telnet, only the default password (password) is required.
4. Enter enable at the >prompt and enter the enable password when prompted. The default
password is password.
CHANGE LOGIN PASSWORDS
1. To modify the user accounts and passwords, from the (config)# prompt, enter the command
username <username> password <password> to modify current user accounts or create a
new one.
2. To modify the Enable mode password, from the (config)# prompt, enter the command
enable password <password>.
3. To modify the Telnet password, from the (config)# prompt, enter the command line telnet 0
4and then press <Enter>. Enter the command password <password>.
4. Enter do write to save the current configuration.
FACTORY DEFAULT SWITCH
• If the factory default switch (shown in the illustration above) is pressed during bootup (while
the STAT LED is flashing green), the unit will stay in bootstrap mode (the STAT LED will turn
solid amber when the unit is in bootstrap mode). Since the unit has no serial port, Telnet has
been built into the boot code. The default IP address is 10.10.10.1.
• If the factory default switch is pressed and held for 5 seconds after boot, the switch ports
1 through 4 on the NetVanta 3100 Series routers will default to 10.10.10.1 and all firewall
access policies will be removed from that interface.
1234
ADSL
10
Default
Switch
• If the factory default switch is pressed and held for approximately 70 seconds, a default
configuration will overwrite your existing configuration and reboot the unit. When the default
configuration is being applied the STAT, WAN, INET, and VPN LEDs will cycle. At this point
the default switch can be released.
For more information on restoring factory defaults, refer to the guide Restoring an AOS Device to
Factory Default available online at https://supportforums.adtran.com.
To factory default the unit, the default switch must be pressed WHILE the
STAT light on the front of the unit is solid green. Do not press the default
switch BEFORE the STAT light is solid green, as this will cause boot to be
missed.
FRONT PANEL LEDS
LED Color Indication
STATUS
(STAT)
Green (flashing) The unit is powering up. On power-up, the STAT LED flashes
rapidly for five seconds.
Green (solid) The power is on and self-test passed.
Red (solid) The power is on, but the self-test failed or the boot mode (if
applicable) code could not be booted.
Amber (solid) The unit is in bootstrap mode.
ETH1 Off The port is administratively disabled or does not have link.
(3120 only) Green (solid) The port is enabled and the link is up.
Amber (flashing) The port has activity (transmit or receive).
WAN Off The interface is administratively down.
(3130 only) Green (solid) The link is up and everything is operational.
Red (solid) An alarm condition is occurring on the WAN interface, or
there is a self-test failure.
Amber (solid) The unit is in test.
VPN Off No encrypted traffic.
On Encrypted traffic present.
INET Green (solid) The unit has a fixed IP address, or has obtained an IP
address through DHCP.
Green (flashing) Traffic is present on the ADSL WAN interface (3130 only).
Red (solid) The unit failed to obtain an IP address through IPCP or
DHCP (3130 only).
Red (flashing) The DHCP client is rebooting (3120 only).
Amber (flashing) No IP address has been obtained through DHCP (3120
only).
SWITCH (1Off The port is administratively disabled or does not have link.
through 4) Green (solid) The port is enabled and the link is up.
Amber (flashing) The port has activity (transmit or receive).

2 Support - Phone: [phone], Email: [e-mail] Quick Start Guide, 61700601G2-13E, March 2015 3
4. Select Apply. If PPP or PPPoE is selected as the Interface Mode, you will be taken to the
PPP page after selecting Apply. Here you will need to select the type of authentication
needed, authentication passwords, and the Address Type. In most cases, you will want the
Address Type to be Negotiated. Select Apply when all the information is complete.
ACCESS THE CLI
If needed, you can access the CLI from a Telnet or SSH client. To access the CLI using a Telnet
or SSH client, follow these steps:
1. Connect the unit to your PC, using an Ethernet cable connected to one of the Ethernet ports
(Ethernet 1, 2, 3, or 4) on the rear of the unit.
2. Use a Telnet or SSH client to connect to 10.10.10.1. If you have changed your unit's IP
address, you will need to enter that address.
3. For SSH, log into the unit using the default login (admin) and password (password). For
Telnet, only the default password (password) is required.
4. Enter enable at the >prompt and enter the enable password when prompted. The default
password is password.
CHANGE LOGIN PASSWORDS
1. To modify the user accounts and passwords, from the (config)# prompt, enter the command
username <username> password <password> to modify current user accounts or create a
new one.
2. To modify the Enable mode password, from the (config)# prompt, enter the command
enable password <password>.
3. To modify the Telnet password, from the (config)# prompt, enter the command line telnet 0
4and then press <Enter>. Enter the command password <password>.
4. Enter do write to save the current configuration.
FACTORY DEFAULT SWITCH
• If the factory default switch (shown in the illustration above) is pressed during bootup (while
the STAT LED is flashing green), the unit will stay in bootstrap mode (the STAT LED will turn
solid amber when the unit is in bootstrap mode). Since the unit has no serial port, Telnet has
been built into the boot code. The default IP address is 10.10.10.1.
• If the factory default switch is pressed and held for 5 seconds after boot, the switch ports
1 through 4 on the NetVanta 3100 Series routers will default to 10.10.10.1 and all firewall
access policies will be removed from that interface.
1234
ADSL
10
Default
Switch
• If the factory default switch is pressed and held for approximately 70 seconds, a default
configuration will overwrite your existing configuration and reboot the unit. When the default
configuration is being applied the STAT, WAN, INET, and VPN LEDs will cycle. At this point
the default switch can be released.
For more information on restoring factory defaults, refer to the guide Restoring an AOS Device to
Factory Default available online at https://supportforums.adtran.com.
To factory default the unit, the default switch must be pressed WHILE the
STAT light on the front of the unit is solid green. Do not press the default
switch BEFORE the STAT light is solid green, as this will cause boot to be
missed.
FRONT PANEL LEDS
LED Color Indication
STATUS
(STAT)
Green (flashing) The unit is powering up. On power-up, the STAT LED flashes
rapidly for five seconds.
Green (solid) The power is on and self-test passed.
Red (solid) The power is on, but the self-test failed or the boot mode (if
applicable) code could not be booted.
Amber (solid) The unit is in bootstrap mode.
ETH1 Off The port is administratively disabled or does not have link.
(3120 only) Green (solid) The port is enabled and the link is up.
Amber (flashing) The port has activity (transmit or receive).
WAN Off The interface is administratively down.
(3130 only) Green (solid) The link is up and everything is operational.
Red (solid) An alarm condition is occurring on the WAN interface, or
there is a self-test failure.
Amber (solid) The unit is in test.
VPN Off No encrypted traffic.
On Encrypted traffic present.
INET Green (solid) The unit has a fixed IP address, or has obtained an IP
address through DHCP.
Green (flashing) Traffic is present on the ADSL WAN interface (3130 only).
Red (solid) The unit failed to obtain an IP address through IPCP or
DHCP (3130 only).
Red (flashing) The DHCP client is rebooting (3120 only).
Amber (flashing) No IP address has been obtained through DHCP (3120
only).
SWITCH (1Off The port is administratively disabled or does not have link.
through 4) Green (solid) The port is enabled and the link is up.
Amber (flashing) The port has activity (transmit or receive).

Quick Start Guide, 61700601G2-13E, March 2015 1
NETVANTA 3100 SERIES ROUTER
P/N 1700601G2, 1700611G2, 1700612G2
4 Copyright © 2015 ADTRAN, Inc. All Rights Reserved.
GETTING STARTED
Two configuration methods are available for your NetVanta unit:
• Web-based graphical user interface (GUI)
• ADTRAN Operating System (AOS) command line interface (CLI)
The GUI lets you configure the main unit settings, and provides online guidance, explanations for
each setting, and configuration wizards to help you get started. However, using the AOS CLI may
be necessary for more advanced configurations.
ACCESS THE GUI
You may access the GUI from any web browser on your network by following these steps:
1. Connect the router to your PC, using an Ethernet cable connected to one of the four ports on
the back of the unit (Ethernet 1,2,3, or 4).
2. Set your PC to a fixed IP address in the 10.10.10.0 /24 subnet. For example configure your
PC with the following settings:
IP Address: 10.10.10.2
Subnet Mask: 255.255.255.0
Neither a default gateway nor DNS server needs to be configured to connect to the unit. If
you cannot change your PC’s IP address, you will need to change the Unit’s IP address
using the CLI as explained in the section below.
3. Open a web browser and enter the unit’s IP address in your browser address line as follows:
http://10.10.10.1. The default IP address is 10.10.10.1, but if you had to change the unit’s IP
address using the CLI, enter that address in the browser line.
4. You will then be prompted for the user name and password (the default settings are admin
and password).
5. The initial GUI screen appears. You can access initial setup information by selecting Setup
Wizard from the menu on the left.
6. ADTRAN recommends changing the default password. Browse to System >Passwords. In
the Login Configuration section, enter a new Username and Password and select Apply
Changes.
CONFIGURE THE ATM PVC (NETVANTA 3130 ONLY)
1. Select the Getting Started link under the System menu. This brings up a side bar menu.
2. Select Step 1 - Configure the Public Interface at the top of the side bar menu to open the
ATM PVC menu.
3. Enter the PVC number and select an Interface Mode. Usually this is PPP or PPPoE;
however, if IP routing is chosen, you will need to enter an IP address.
By default, the NetVanta 3130 comes with an ADSL and an asynchronous
transfer mode (ATM) port already configured and enabled. The service
provider should provide a PVC (VPI/VCI) number, which will be used to
configure the ATM PVC.
CONFIGURE YOUR APPLICATION
The applications you will need to configure vary by product and by network. Review the list of
defaults for your unit before deciding what applications to configure. The following are some
common applications that should be configured on startup. These are all available online on
ADTRAN’s Support Community
NETVANTA 3100 SERIES DEFAULTS
Configuring Internet Access (Many to
one NAT) with the Firewall Wizard
in AOS
Configuring Port Forwarding in AOS
Configuring QoS for VOIP in AOS Configuring ADSL Internet Access in AOS
Configuring QoS in AOS Configuring DHCP Server in AOS
Configuring a VPN using Main Mode
in AOS
Configuring a VPN using Aggressive Mode
in AOS
Important: For additional details on product features, specifications,
installation, and safety, refer to the NetVanta 3100 Series Fixed Port
Routers Hardware Installation Guide available online at
https://supportforums.adtran.com.
Feature Default Value
IP Address 10.10.10.1
Username admin
Password password
HTTP Server Enabled
Event History On
IP Routing Enabled
DHCP Enabled
VLAN Interface Enabled (vlan 1) with IP address 10.10.10.1
Firewall Enabled
NAT Overload to eth 0/1 address (3120)
Overload to ppp 1 address (3130)