ADTRAN NetVanta 3000 Series Manual

NETVANTA 3000 SERIES ROUTERS
Hardware Installation Guide
1202860L1 NetVanta 3200 Unit
1200870L1 NetVanta 3205 Unit (AC Version)
1200980L1 NetVanta 3205 Unit (DC Version)
1200880L1 NetVanta 3305 Unit
1200861L1 NetVanta 56K/64K Network Interface Module
1200862L1 NetVanta T1/FT1 Network Interface Module
1200863L1 NetVanta T1/FT1+DSX-1 Network Interface Module
1200866L1 NetVanta Serial Network Interface Module
1200867L1 NetVanta SHDSL Network Interface Module
1200864L1 NetVanta Analog Modem Dial Backup Interface Module
1200865L1 NetVanta ISDN BRI Dial Backup Interface Module
1200868L1 NetVanta E1/FE1 Network Interface Module
1200878L1 NetVanta E1/FE1 w/ G.703 DROP
1202368L1 NetVanta 3305 Accelerator Card
61200860L1-34C
July 2003

Hardware Installation Guide NetVanta 3000 Series Routers
2 © 2003 ADTRAN, Inc. 61200860L1-34C
Trademarks
Any brand names and product names included in this manual are trademarks, registered trademarks, or
trade names of their respective holders.
To the Holder of this Manual
The contents of this manual are current as of the date of publication. ADTRAN reserves the right to change
the contents without prior notice.
In no event will ADTRAN be liable for any special, incidental, or consequential damages or for
commercial losses even if ADTRAN has been advised thereof as a result of issue of this publication.
901 Explorer Boulevard
P.O. Box 140000
Huntsville, AL 35814-4000
Phone: [phone]
www.adtran.com
© 2003 ADTRAN, Inc.
All Rights Reserved.
Printed in U.S.A.

NetVanta 3000 Series Routers Hardware Installation Guide
61200860L1-34C © 2003 ADTRAN, Inc. 3
Conventions
Safety Instructions
When using your communications equipment, please follow these basic safety precautions to reduce the
risk of fire, electrical shock, or personal injury:
1. Do not use this product near water such as a bathtub, wash bowl, kitchen sink, laundry tub, in a
wet basement, or near a swimming pool.
2. Avoid using a telephone (other than a cordless-type) during an electrical storm. There is a remote
risk of shock from lightning.
3. Do not use a telephone to report a gas leak in the vicinity of the leak.
4. Use only the power cord, power supply, and/or batteries indicated in the manual.
5. Do not dispose of batteries in a fire. They may explode. Check with local codes for special
disposal instructions.
Save These Important Safety Instructions
Notes provide additional useful information.
Cautions signify information that could prevent service interruption.
Warnings provide information that could prevent damage to the equipment or
endangerment to human life.
Changes or modifications to this unit not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment.

Hardware Installation Guide NetVanta 3000 Series Routers
4 © 2003 ADTRAN, Inc. 61200860L1-34C
FCC regulations require that the following information be provided in this manual:
1. This equipment complies with Part 68 of FCC rules and requirements adopted by ACTA. Each of
the Network Interface Modules and the Dial Backup Interface Modules has a label showing the
FCC registration number and ringer equivalence number (REN). If requested, provide this
information to the telephone company.
2. If this equipment causes harm to the telephone network, the telephone company may temporarily
discontinue service. If possible, advance notification is given; otherwise, notification is given as
soon as possible. The telephone company will advise the customer of the right to file a complaint
with the FCC.
3. The telephone company may make changes in its facilities, equipment, operations, or procedures
that could affect the proper operation of this equipment. Advance notification and the opportunity
to maintain uninterrupted service are given.
4. If experiencing difficulty with this equipment, please contact ADTRAN for repair and warranty
information. The telephone company may require this equipment to be disconnected from the
network until the problem is corrected or it is certain the equipment is not malfunctioning.
5. This unit contains no user-serviceable parts.
6. An FCC compliant telephone cord with a modular plug is provided with this equipment. This
equipment is designed to be connected to the telephone network or premises wiring using an FCC
compatible modular jack, which is compliant with Part 68 and requirements adopted by ACTA.
7. The following information may be required when applying to the local telephone company for a
dial-up line for the analog modem:
8. The REN is useful in determining the quantity of devices you may connect to your telephone line
and still have all of those devices ring when your number is called. In most areas, the sum of the
RENs of all devices should not exceed five. To be certain of the number of devices you may
connect to your line as determined by the REN, call your telephone company to determine the
maximum REN for your calling area.
9. This equipment may not be used on coin service provided by the telephone company. Connection
to party lines is subject to state tariffs. Contact your state public utility commission or corporation
commission for information.
Part Number Registration Number Service Type REN/SOC FIC USOC
1200861L1 US:HDCDENAN1200861L1 56 Kbps Digital Interface
64 Kbps Digital Interface 6.0F 04DU5-56 04DU5-64 RJ-48S
1200862L1
US: HDCDENAN1200863L1
1.544 Mbps - SF
1.544 Mbps - SF and B8ZS 6.0N
04DU9-BN
04DU9-DN RJ-48C
1200863L1 1.544 Mbps - ESF
1.544 Mbps - ESF and B8ZS 04DU9-1KN 04DU9-1SN
1200864L1 US: HDCM504A1200864L1 Analog Loop Start 0.4A/9.0F 02LS2 RJ-11C
1200865L1 US: HDCDENAN1200865L1 Basic Rate ISDN 6.0F 021S5 RJ-49C

NetVanta 3000 Series Routers Hardware Installation Guide
61200860L1-34C © 2003 ADTRAN, Inc. 5
FCC Radio Frequency Interference Statement
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15
of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the
equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency
energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to
radio frequencies. Operation of this equipment in a residential area is likely to cause harmful interference in which
case the user will be required to correct the interference at his own expense.
Canadian Emissions Requirements
This digital apparatus does not exceed the Class A limits for radio noise emissions from digital apparatus as set out in
the interference-causing equipment standard entitled “Digital Apparatus,” ICES-003 of the Department of
Communications.
Cet appareil numérique respecte les limites de bruits radioelectriques applicables aux appareils numériques de Class
A prescrites dans la norme sur le materiel brouilleur: “Appareils Numériques,” NMB-003 edictee par le ministre des
Communications.
Electromagnetic Compatibility (EMC) Table
NetVanta Module P/N and Name NetVanta 3200 (1202860L1) NetVanta 3205
AC: 1200870L1 / DC: 1200980L1 NetVanta 3305 (1200880L1)
1200861L1 56K/64K NIM FCC Part 15, Class A
EN55022 Class A FCC Part 15, Class A EN55022 Class A FCC Part 15, Class A EN55022 Class A
1200862L1 T1/FT1 NIM FCC Part 15, Class B
EN55022 Class B FCC Part 15, Class A EN55022 Class A FCC Part 15, Class A EN55022 Class A
1200863L1 T1/FT1+DSX-1 NIM FCC Part 15, Class B
EN55022 Class B FCC Part 15, Class A EN55022 Class A FCC Part 15, Class A EN55022 Class A
1200866L1 Serial NIM FCC Part 15, Class B
EN55022 Class B
EN55024
EN61000-3-2
EN61000-3-3
FCC Part 15, Class A
EN55022 Class A
EN55024
EN61000-3-2
EN61000-3-3
FCC Part 15, Class A
EN55022 Class A
EN55024
EN61000-3-2
EN61000-3-3
1200867L1 SHDSL NIM FCC Part 15, Class B
EN55022 Class B
EN55024
EN61000-3-2
EN61000-3-3
FCC Part 15, Class A
EN55022 Class A
EN55024
EN61000-3-2
EN61000-3-3
FCC Part 15, Class A
EN55022 Class A
EN55024
EN61000-3-2
EN61000-3-3
1200864L1 Analog Modem DBU FCC Part 15, Class B
EN55022 Class B FCC Part 15, Class A EN55022 Class A FCC Part 15, Class A EN55022 Class A
1200865L1 ISDN BRI DBU FCC Part 15, Class B
EN55022 Class B FCC Part 15, Class A EN55022 Class A FCC Part 15, Class A EN55022 Class A
1200868L1 E1/FE1 NIM FCC Part 15, Class B
EN55022 Class B
EN55024
EN61000-3-2
EN61000-3-3
FCC Part 15, Class A
EN55022 Class A
EN55024
EN61000-3-2
EN61000-3-3
FCC Part 15, Class A
EN55022 Class A
EN55024
EN61000-3-2
EN61000-3-3
1200878L1 E1/FE1 w/ G.703 Drop FCC Part 15, Class B
EN55022 Class B
EN55024
EN61000-3-2
EN61000-3-3
FCC Part 15, Class A
EN55022 Class A
EN55024
EN61000-3-2
EN61000-3-3
FCC Part 15, Class A
EN55022 Class A
EN55024
EN61000-3-2
EN61000-3-3
1202368L1 3305 Encryption Card N/A N/A FCC Part 15, Class A
EN55022 Class A
EN55024
EN61000-3-2
EN61000-3-3

Hardware Installation Guide NetVanta 3000 Series Routers
6 © 2003 ADTRAN, Inc. 61200860L1-34C
Industry Canada Compliance Information
Notice: The Industry Canada label applied to the product (identified by the Industry Canada logo or the “IC:” in front
of the certification/registration number) signifies that the Industry Canada technical specifications were met.
Notice: The Ringer Equivalence Number (REN) for this terminal equipment is supplied in the documentation or on
the product labeling/markings. The REN assigned to each terminal device indicates the maximum number of
terminals that can be connected to a telephone interface. The termination on an interface may consist of any
combination of devices subject only to the requirement that the sum of the RENs of all the devices should not exceed
five (5).
Affidavit Requirements for Connection to Digital Services
• An affidavit is required to be given to the telephone company whenever digital terminal equipment without
encoded analog content and billingprotection is used totransmit digital signals containing encoded analog content
which are intended for eventual conversion into voiceband analog signals and transmitted on the network.
• The affidavit shall affirm that either no encoded analog content or billing information is being transmitted or that
the output of the device meets Part 68 encoded analog content or billing protection specifications.
• End user/customer will be responsible for filing an affidavit with the local exchange carrier when connecting
unprotected customer premise equipment (CPE) to 1.544 Mbps or subrate digital services.
• Until such time as subrate digital terminal equipment is registered for voice applications, the affidavit requirement
for subrate services is waived.

NetVanta 3000 Series Routers Hardware Installation Guide
61200860L1-34C © 2003 ADTRAN, Inc. 7
Affidavit for Connection Of Customer Premises Equipment to 1.544 Mbps And/or Subrate Digital Services
For the work to be performed in the certified territory of ___________________(telco name)
State of ________________
County of ________________
I, _______________________ (name), _____________________________(business address),
____________________ (telephone number) being duly sworn, state:
I have responsibility for the operation and maintenance of the terminal equipment to be connected to 1.544 Mbps and/or ________ subrate
digital services. The terminal equipment to be connected complieswith Part 68 of the FCC rules except for the encoded analog content and
billing protection specifications. With respect to encoded analog content and billing protection:
( ) I attest that all operations associated with the establishment, maintenance, and adjustment of the digital CPE with respect to analog content
and encoded billing protection information continuously complies with Part 68 of the FCC Rules and Regulations.
( ) The digital CPE does not transmit digital signals containing encoded analog content or billing information which is intended to be decoded
within the telecommunications network.
( ) The encoded analog content and billing protection is factory set and is not under the control of the customer.
I attest that the operator(s)/maintainer(s) of the digital CPE responsible for the establishment, maintenance, and adjustment of the
encoded analog content and billing information has (have) been trained to perform these functions by successfully having completed one
of the following (check appropriate blocks):
( ) A training course provided by the manufacturer/grantee of the equipment used to encode analog signals; or
( ) A training course provided by the customer or authorized representative, using training materials and instructions provided by the
manufacturer/grantee of the equipment used to encode analog signals; or
( ) An independent training course (e.g., trade school or technical institution) recognized by the manufacturer/grantee of the equipment used to
encode analog signals; or
( ) In lieu of the preceding training requirements, the operator(s)/maintainer(s) is (are) under the control of a supervisor trained in accordance with
_________ (circle one) above.
I agree to provide ______________________ (telco’s name) with proper documentation to demonstrate compliance with the information as
provided in the preceding paragraph, if so requested.
_________________________________Signature
_________________________________Title
_________________________________ Date
Transcribed and sworn to before me
This ________ day of _______________, _______
_________________________________
Notary Public
My commission expires:
_________________________________

Hardware Installation Guide NetVanta 3000 Series Routers
8 © 2003 ADTRAN, Inc. 61200860L1-34C
Warranty and Customer Service
ADTRAN will replace or repair this product within the warranty period if it does not meet its published
specifications or fails while in service. Warranty information can be found at: http://support.adtran.com
(Click on Warranty and Repair Information, under Support.)
Product Registration
Registering your product helps ensure complete customer satisfaction. Please take time to register your
products on line at http://support.adtran.com. Click on Product Registration under Support.
Product Support Information
A return material authorization (RMA) is required prior to returning equipment to ADTRAN. For service,
RMA requests, training, or more information, use the following contact information:.
Repair and Return
If you determine that a repair is needed, please contact our Customer and Product Service (CaPS)
department to have an RMA number issued. CaPS should also be contacted to obtain information
regarding equipment currently in house or possible fees associated with repair.
Identify the RMA number clearly on the package (below address), and return to the following address:
CaPS Department [phone]
ADTRAN Customer and Product Service
901 Explorer Blvd. (East Tower)
Huntsville, Alabama 35806
RMA # _____________

NetVanta 3000 Series Routers Hardware Installation Guide
61200860L1-34C © 2003 ADTRAN, Inc. 9
Pre-Sales Inquiries and Applications Support
Your reseller should serve as the first point of contact for support. If additional pre-sales support is needed,
the ADTRAN Support web site provides a variety of support services such as a searchable knowledge
base, latest product documentation, application briefs, case studies, and a link to submit a question to an
Applications Engineer. All of this, and more, is available at:
When needed, further pre-sales assistance is available by calling our Applications Engineering
Department.
Post-Sale Support
Your reseller should serve as the first point of contact for support. If additional support is needed, the
ADTRAN Support web site provides a variety of support services such as a searchable knowledge base,
updated firmware releases, latest product documentation, service request ticket generation and
trouble-shooting tools. All of this, and more, is available at:
When needed, further post-sales assistance is available by calling our Technical Support Center. Please
have your unit serial number available when you call.
Installation and Maintenance Support
The ADTRAN Custom Extended Services (ACES) program offers multiple types and levels of installation
and maintenance services which allow you to choose the kind of assistance you need. This support is
available at:
For questions, call the ACES Help Desk.
http://support.adtran.com
Applications Engineering [phone]
http://support.adtran.com
Technical Support (888) 4ADTRAN
International Technical Support 1-256-963-8716
http://www.adtran.com/aces
ACES Help Desk (888) 874-ACES (2237)

Hardware Installation Guide NetVanta 3000 Series Routers
10 © 2003 ADTRAN, Inc. 61200860L1-34C
Training
The Enterprise Network (EN) Technical Training Department offers training on our most popular products.
These courses include overviews on product features and functions while covering applications of
ADTRAN's product lines. ADTRAN provides a variety of training options, including customized training
and courses taught at our facilities or at your site. For more information about training, please contact your
Territory Manager or the Enterprise Training Coordinator.
Training Phone [phone], ext. 7500
Training Fax [phone]
Training Email [e-mail]

61200860L1-34C © 2003 ADTRAN, Inc. 11
HARDWARE INSTALLATION GUIDE
Contents
Introduction to the NetVanta Solution. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Features and Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Unpack and Inspect the System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Contents of ADTRAN Shipments . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Product Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Reviewing the Base Unit Front Panel Designs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Front Panel LEDs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Reviewing the Base Unit Rear Panel Designs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Rear Panel Interfaces and LEDs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Option Modules . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Network Interface Modules . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
NetVanta 56K/64K NIM (P/N 1200861L1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
NetVanta T1/FT1 NIM (P/N 1200862L1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
NetVanta T1/FT1+DSX-1 NIM (P/N 1200863L1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
NetVanta Serial NIM (P/N 1200866L1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
NetVanta SHDSL NIM (P/N 1200867L1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
NetVanta E1/FE1 NIM (P/N 1200868L1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
NetVanta E1/FE1 with G.703 Drop NIM (P/N 1200878L1) . . . . . . . . . . . . . . . . . . . . . . . . . . 33
Dial Backup Interface Modules . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
NetVanta Analog Modem DIM (P/N 1200864L1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
NetVanta ISDN BRI DIM (P/N 1200865L1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
Unit Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
Tools Required . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
Mounting Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
Rackmounting NetVanta 3000 Series Routers. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
Wallmounting NetVanta 3000 Series Routers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
Supplying Power to the Unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
NetVanta 3200 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
NetVanta 3205 (AC) and NetVanta 3305 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
NetVanta 3205 (DC). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
Installing Dial Backup and Network Interface Modules . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
Installing the NetVanta VPN Accelerator Card (1202368L1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
Base Unit Pinouts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
NIM Pinouts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49

Hardware Installation Guide NetVanta 3000 Series Routers
12 © 2003 ADTRAN, Inc. 61200860L1-34C
FIGURES
Figure 1. NetVanta 3200 Front Panel Layout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Figure 2. NetVanta 3205 Front Panel Layout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Figure 3. NetVanta 3305 Front Panel Layout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Figure 4. NetVanta 3200 Rear Panel Layout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Figure 5. NetVanta 3205 (AC version) Rear Panel Layout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Figure 6. NetVanta 3205 (DC version) Rear Panel Layout. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Figure 7. NetVanta 3305 Rear Panel Layout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Figure 8. NetVanta 56K/64K NIM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Figure 9. NetVanta T1/FT1 NIM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Figure 10. NetVanta T1/FT1+DSX-1 NIM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Figure 11. NetVanta Serial NIM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Figure 12. NetVanta SHDSL NIM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
Figure 13. NetVanta E1/FE1 NIM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Figure 14. NetVanta E1/FE1 with G.703 Drop NIM. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
Figure 15. Wallmounting the NetVanta 3200 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
Figure 16. Repositioning the Mounting Bracket . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
Figure 17. Wallmounting the NetVanta 3205/NetVanta 3305 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
Figure 18. Installing DIMs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
Figure 19. NIM and DIM Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
Figure 20. VPN Card Installation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
TABLES
Table 1. NetVanta 3000 Series Routers LEDs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Table A. 10/100BaseT Ethernet Port Pinouts. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
Table B. Console Port (DCE) Pinouts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
Table C. Console Port (DCE) Pinout for NetVanta 3200 (p/n 1202860L1). . . . . . . . . . . . . . . . . . . 48
Table D. DC Power Supply Connection (NetVanta 3205 DC Version Only) . . . . . . . . . . . . . . . . . 48
Table E. WAN-DDS Connector Pinouts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49
Table F. WAN-T1 Connector Pinouts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49
Table G. WAN-E1 Connector Pinouts. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49
Table H. DSX-1 Connector Pinouts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50
Table I. G.703 Connector Pinouts. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .50
Table J. WAN-SHDSL Connector Pinouts. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50
Table K. Serial NIM Connector Pinouts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51
Table L. DBU Connector Pinouts. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .51
Table M. E1 DBU Connector Pinouts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51

NetVanta 3000 Series Routers Hardware Installation Guide
61200860L1-34C © 2003 ADTRAN, Inc. 13
1. INTRODUCTION TO THE NETVANTA SOLUTION
The NetVanta 3000 Series is a line of modular access routers designed for cost-effective branch office
connectivity over frame relay or point-to-point (PPP) networks. These modular platforms offer a complete
solution for access routing and WAN connectivity in a single, compact package.
The Netvanta 3000 Series includes the NetVanta 3200, NetVanta 3205 (AC or DC powered), and NetVanta
3305. These main base units support a variety of interchangeable network interface modules (NIMs) and
dial backup interface modules (DIMs).
All three base units provide the same features, perform the same functions, and use the same interface
modules. The main differences in the base units include the following:
• Type of enclosure: NetVanta 3200 is a stand-alone unit in a plastic housing, while NetVanta 3205 and
NetVanta 3305 are housed in 1U high, rack-mountable metal enclosures.
• Number of card slots: NetVanta 3200 and NetVanta 3205 have one option card (module) slot, while
NetVanta 3305 has two.
• Number of Ethernet ports: NetVanta 3200 and NetVanta 3205 have one Ethernet port, while NetVanta
3305 has two.
The NIMs are plug-in modules that offer a variety of WAN connectivity. These modules provide 56K/64K
(DDS), SHDSL, T1/FT1, T1/FT1 with DSX-1, E1/FE1, E1/FE1 with G.703 Drop, and Serial (V.35/X.21)
interfaces. An analog modem or ISDN BRI (U Interface) DIM plugs on to the NIM, providing added dial
backup capability. The DIMs plug on to the NIM modules, and the NIMs slide into the rear of the base
unit. Refer to Installing Dial Backup and Network Interface Modules on page 41 for more details. In
addition, the optional VPN Accelerator Card plugs into a 32-bit PCI slot in the NetVanta 3305 and
following products to provide encryption/decryption and security acceleration services for the host
processor.
Features and Specifications
The NetVanta 3000 Series Routers have the following features:
• Modular network interface: 56K/64K, SHDSL, T1/FT1, T1/FT1+DSX-1, E1/FE1, E1/FE1+G.703
Drop, or Serial Interface
• Optional VPN Accelerator Card plugs into a 32-bit PCI slot in the NetVanta 3305 and following
products to provide encryption/decryption and security acceleration services
• Integrated 10/100BaseT Ethernet port (RJ-48C)
• WAN Protocol: Frame Relay or PPP
• Integrated IP router with bridging
• IP encapsulation over Frame Relay (RFC 1490)
• Command Line Interface (CLI)
• SNMP management
• N-Formant web-based management
• Integrated EIA-232 DCE configuration port (DB-9)
• Optional dial backup (ISDN BRI or analog modem)
• Front panel LEDs

Hardware Installation Guide NetVanta 3000 Series Routers
14 © 2003 ADTRAN, Inc. 61200860L1-34C
• NetVanta 3200: 9.3”W x 2.1”H x 6.1”D
• NetVanta 3205 and NetVanta 3305: 17.25” x 1.26”H x 7.75”D
• AC power requirements: 6 W max, 60mA (regardless of configuration)
• DC power requirements: 6 W max; +21 to +28.3 VDC (+24 VDC nominal);
-40.5 to -64 VDC (-48 VDC nominal)
This hardware installation guide describes the NetVanta 3000 Series units, details basic functionality, gives
installation instructions, and lists unit specifications. For more information on router configuration for a
specific application, refer to the quick start documents provided on your ADTRAN OS System
Documentation CD. For details on the command line interface, refer to the Command Reference Guide
also on the CD.
Unpack and Inspect the System
Each NetVanta 3000 Series Routers unit is shipped in its own cardboard shipping carton. Open each carton
carefully and avoid deep penetration into the carton with sharp objects.
After unpacking the unit, inspect it for possible shipping damage. If the equipment has been damaged in
transit, immediately file a claim with the carrier and contact ADTRAN Customer Service (see Warranty
and Customer Service on page 8).
Contents of ADTRAN Shipments
NetVanta 3200
Shipments of the NetVanta 3200 include the following items:
• NetVanta 3200 Base Unit
•ADTRAN OS System Documentation CD
• Warranty Card
• AC Power Supply
NetVanta 3205 (AC version) and NetVanta 3305
Shipments of the NetVanta 3205 (AC) and NetVanta 3305 include the following items:
• NetVanta 3205 (AC version) or NetVanta 3305 base unit with attached mounting ears/screws
• ADTRAN OS System Documentation CD
• Warranty Card
• Detachable AC power cord
In this document, the term “NetVanta 3000 Series Routers” means the NetVanta 3200,
NetVanta 3205, and NetVanta 3305. If a statement only applies to one particular router, the
text refers to the router individually.

NetVanta 3000 Series Routers Hardware Installation Guide
61200860L1-34C © 2003 ADTRAN, Inc. 15
NetVanta 3205 (DC version)
Shipments of the NetVanta 3205 (DC) include the following items:
• NetVanta 3205 (DC version) base unit with attached mounting ears
• ADTRAN OS System Documentation CD
• Warranty Card
NetVanta 56K/64K NIM
Shipments of the 56K/64K NIM include the following items:
• 56K/64K Network Interface Module
•QuickStartGuide
• 6-foot RJ-45 to RJ-45 cable (ADTRAN P/N 3127004)
NetVanta T1/FT1 NIM (1200862L1)
Shipments of the T1/FT1 NIM include the following items:
• T1/FT1 Network Interface Module
•QuickStartGuide
• 15-foot RJ-45 to RJ-45 cable (ADTRAN P/N 3125M008@A)
NetVanta T1/FT1+ DSX-1 NIM (1200863L1)
Shipments of the T1/FT1 + DSX-1 NIM include the following items:
• T1/FT1 + DSX-1 Network Interface Module
•QuickStartGuide
• 15-foot RJ-45 to RJ-45 cable (ADTRAN P/N 3125M008@A)
NetVanta E1/FE1 NIM (1200868L1)
Shipments of the E1/FE1 NIM include the following items:
• E1/FE1 Network Interface Module
•QuickStartGuide
• 15-foot RJ-45 to RJ-45 cable (ADTRAN P/N 3125M008@A)
NetVanta E1/FE1+ G.703 NIM (1200878L1)
Shipments of the E1/FE1+ G.703 NIM include the following items:
• E1/FE1+ G.703 Network Interface Module
•QuickStartGuide
• 15-foot RJ-45 to RJ-45 cable (ADTRAN P/N 3125M008@A)
NetVanta Serial NIM (1200866L1)
Shipments of the Serial NIM include the following items:
• Serial Network Interface Module
•QuickStartGuide

Hardware Installation Guide NetVanta 3000 Series Routers
16 © 2003 ADTRAN, Inc. 61200860L1-34C
NetVanta Analog Modem DIM (1200864L1)
Shipments of the Analog Modem DIM include the following items:
• Analog Modem Dial Backup Interface Module
•QuickStartGuide
• RJ-45 to RJ-11 cable (ADTRAN P/N 3125M007@A)
NetVanta ISDN BRI DIM (1200865L1)
Shipments of the ISDN BRI DIM include the following items:
• ISDN BRI Dial Backup Interface Module
•QuickStartGuide
• RJ-45 to RJ-11 cable (ADTRAN P/N 3125M007@A)
NetVanta VPN Accelerator Card (1202368L1)
Shipments of the VPN Accelerator Card include the following items:
• VPN Accelerator Card
•QuickStartGuide
Option modules are intended to be serviced by qualified service personnel only.
System bundles are shipped with a base unit, a network interface module, and other appro-
priate contents based on the system-level solution ordered.

NetVanta 3000 Series Routers Hardware Installation Guide
61200860L1-34C © 2003 ADTRAN, Inc. 17
2. PRODUCT OVERVIEW
Reviewing the Base Unit Front Panel Designs
Figure 1 shows the NetVanta 3200 front panel.
Figure 1. NetVanta 3200 Front Panel Layout
Figure 2 shows the NetVanta 3205 front panel.
Figure 2. NetVanta 3205 Front Panel Layout
Figure 3 shows the NetVanta 3305 front panel.
Figure 3. NetVanta 3305 Front Panel Layout

Hardware Installation Guide NetVanta 3000 Series Routers
18 © 2003 ADTRAN, Inc. 61200860L1-34C
Front Panel LEDs
Table 1 describes the front panel LEDs.
Table 1. NetVanta 3000 Series Routers LEDs
For these
LEDs… This activity… Indicates that…
STATUS Green (blinking) The unit is powering up. On power-up the STAT LED
blinks rapidly for five seconds, during which time the user
may escape to boot mode from the console port.
Green (solid) The power is on and self-test passed.
Red (solid) The power is on, but the self-test failed or the boot mode
(if applicable) code could not be booted.
WAN Off No NIM is installed or interface is administratively down.
Green (solid) The link is up and everything is okay.
Red (solid) An alarm condition is occurring on the WAN interface, or
there is a self-test failure.
Yellow (solid) The unit is in test.
DBU Off No DIM is installed.
Green (solid) The DIM is ready. For the ISDN BRI DIM, green solid
indicates that the negotiation with the switch is complete.
Green (blinking) The unit is in dial backup.
Red (solid) An alarm condition is occurring on the DBU interface, or
there is a self-test failure.
Yellow (solid) The unit is in test.
NET TD/RD Green (blinking) There is activity on the WAN or DBU port.
Off There is no activity on the WAN or DBU port.
LAN TD/RD Green (blinking) There is activity on the Ethernet port.
Off There is no activity on the Ethernet port.
LNK Green (solid) The 10BaseT Ethernet link is up.
Yellow (solid) The 100BaseT Ethernet link is up.

NetVanta 3000 Series Routers Hardware Installation Guide
61200860L1-34C © 2003 ADTRAN, Inc. 19
Reviewing the Base Unit Rear Panel Designs
Figure 4 through Figure 7 show the rear panels for the NetVanta 3000 Series Routers. Each chassis is
shown with the T1/FT1+DSX-1 NIM installed. The Activity and Link LEDs, which are present on all
NetVanta Ethernet ports, are pointed out in Figure 4.
Figure 4. NetVanta 3200 Rear Panel Layout
Figure 5. NetVanta 3205 (AC version) Rear Panel Layout
Figure 6. NetVanta 3205 (DC version) Rear Panel Layout
Figure 7. NetVanta 3305 Rear Panel Layout
POWER
12V
ETH 0/1 CONSOLE
SLOT 1NET/DBU
NOTE: OPTIONAL MODULE
REQUIRED FOR DBU.
WAN-T1 DSX-1 DBU
Activity LED Link LED
ETH 0/1
SLOT 2 NET/DBU
CONSOLE
WAN-T1 DSX-1 DBU
SLOT 1 NET/DBU
WAN-T1 DSX-1 DBU
ETH 0/2ETH 0/1
100-250VAC
50/60Hz

Hardware Installation Guide NetVanta 3000 Series Routers
20 © 2003 ADTRAN, Inc. 61200860L1-34C
Rear Panel Interfaces and LEDs
10/100BaseT Ethernet Interface and Activity LEDs
The Ethernet port is an RJ-48C connector with LEDs. The yellow activity LED flashes when data
traffic is being sent or received on the Ethernet port. The green link LED is on when the router has a
good connection to the LAN. See Table A on page 47 for the Ethernet port pinout. The Ethernet port
provides the following:
• 10BaseT or 100BaseT with a single connector
• Auto-negotiation
•CSMA/CD
• IEEE 802.3 compatibility
Console Interface
The CONSOLE interface is an EIA-232 serial port (DCE) which provides for local management and
configuration (via a DB-9 female connector). Table B on page 47 shows the CONSOLE port pinouts,
with the exception of the NetVanta 3200 (p/n 61202860L1) which is shown in Table C on page 48.
NET/DBU Card Slot
The Slot x NET/DBU card slot supports various NIM plug-in cards. These card options are described
in Option Modules on page 21.
Power Supply
Power supplies are shipped with final destinations in mind. For example, the domestic routers are
shipped with a wall mount supply and the international routers are shipped with a universal input
lump-in-line supply with the appropriate cables. All of the 1U products have universal supplies and are
shipped with the appropriate cable. Please refer to Supplying Power to the Unit on page 40 for
connection details.
Connection directly to an external modem requires a cross-over cable.