ADTRAN NetVanta 3200 series User guide

Application Drawings: Routing across the WAN
Revision C Page 1 of 27
Application Drawings
Netvanta 3200/3205: Routing across the WAN
T-1
Host Router Remote Router
Host Switch
Remote Switch
`
PC
`
PC
`
PC
`
PC
`
PC
`
PC
10.0.0.1 10.0.0.2
192.168.1.254 192.168.2.254

Application Drawings: Routing across the WAN
Revision C Page 2 of 27
Overview
This application drawing shows how to use NetVanta 3200s or NetVanta 3205s in a
scenario where there is a point-to-point T-1 that is used for data. The IP addresses used
in the configuration script and configuration steps are just examples and maybe modified
to fit your network.
Table of Contents
Configuration steps using the web interface for NetVanta 3200/3205 “Host Router”:...... 3
Configuration Script for the NetVanta 3200/3205 “Host Router”: .................................. 14
Configuration steps using the web interface for NetVanta 3200/3205 “Remote Router”:16
Configuration Script for the NetVanta 3200/3205 “Remote Router”:.............................. 26

Application Drawings: Routing across the WAN
Revision C Page 3 of 27
Configuration steps using the web interface for NetVanta
3200/3205 “Host Router”:
1. Choose "Physical Interfaces" from the left hand side menu options.
2. Choose "eth 0/1" from the list of physical interfaces displayed.
3. Under the "IP Settings" section type in the new "IP Address" and "Subnet Mask"
you would like to use. In the application drawings example the IP address
192.168.1.254 is used.

Application Drawings: Routing across the WAN
Revision C Page 4 of 27
4. Press the “Apply” button.
Note: If you choose to change the IP address of Ethernet 0/1, you will need to change the
IP address of your workstation to an IP on the same network as Ethernet 0/1 to continue
configuring the router.
5. Choose "Physical Interfaces" from the left hand side menu options.
6. Choose "t1 1/1" from the list of physical interfaces displayed.

Application Drawings: Routing across the WAN
Revision C Page 5 of 27
7. Checked the box next to "Enable".

Application Drawings: Routing across the WAN
Revision C Page 6 of 27
8. Next to “Clocking” choose “Internal”.

Application Drawings: Routing across the WAN
Revision C Page 7 of 27
9. Choose "1" in the first drop down next to "Data DS0s" and "24" in the second
drop down.

Application Drawings: Routing across the WAN
Revision C Page 8 of 27
10. Choose "PPP" next to "Encapsulation".

Application Drawings: Routing across the WAN
Revision C Page 9 of 27
11. Press "Apply" and new screen will appear that is titled "PPP Configuration for
ppp 1".

Application Drawings: Routing across the WAN
Revision C Page 10 of 27
12. Under the "IP Settings" section change "Address Type" to "Static".
13. Fill in the "IP Address" and "Subnet Mask" you would like to use. In the example
it would be 10.0.0.1 and 255.255.255.252

Application Drawings: Routing across the WAN
Revision C Page 11 of 27
14. Press "Apply".
15. Choose "Route Table" from the left hand side menu options.

Application Drawings: Routing across the WAN
Revision C Page 12 of 27
16. Fill in 192.168.2.0 for the "Destination Address" and 255.255.255.0 for the
"Destination Mask".
17. Choose "Address" under "Gateway" and type 10.0.0.2

Application Drawings: Routing across the WAN
Revision C Page 13 of 27
18. Press "Add".
19. Configuration is now done and all that left to do is choose "Save" in the upper
right hand corner.

Application Drawings: Routing across the WAN
Revision C Page 14 of 27
Configuration Script for the NetVanta 3200/3205 “Host
Router”:
!
!
hostname "HostRouter"
enable password adtran
!
ip subnet-zero
ip classless
ip routing
!
event-history on
no logging forwarding
no logging email
logging email priority-level info
!
username "admin" password "adtran"
!
ip policy-timeout tcp telnet 14400
!
!
!
!
!
!
!
!
!
!
!
interface eth 0/1
ip address 192.168.1.254 255.255.255.0
no shutdown
!
!
!
interface t1 1/1
clock source internal
tdm-group 1 timeslots 1-24 speed 64
no shutdown
!
interface ppp 1
ip address 10.0.0.1 255.255.255.252
no shutdown
cross-connect 1 t1 1/1 1 ppp 1
!

Application Drawings: Routing across the WAN
Revision C Page 15 of 27
!
!
!
!
ip route 192.168.2.0 255.255.255.0 10.0.0.2
!
no ip n-form agent
ip http server
no ip http secure-server
no ip snmp agent
no ip ftp agent
!
!
!
!
!
!
!
line con 0
no login
!
line telnet 0 4
login
password adtran
!
end

Application Drawings: Routing across the WAN
Revision C Page 16 of 27
Configuration steps using the web interface for NetVanta
3200/3205 “Remote Router”:
1. Choose "Physical Interfaces" from the left hand side menu options.
2. Choose "eth 0/1" from the list of physical interfaces displayed.
3. Under the "IP Settings" section type in the new "IP Address" and "Subnet Mask"
you would like to use. In the application drawings example, the IP address
192.168.2.254 is used.

Application Drawings: Routing across the WAN
Revision C Page 17 of 27
4. Press the “Apply” button.
Note: If you choose to change the IP address of Ethernet 0/1, you will need to change the
IP address of your workstation to an IP on the same network as Ethernet 0/1 to continue
configuring the router.
5. Choose "Physical Interfaces" from the left hand side menu options.
6. Choose "t1 1/1" from the list of physical interfaces displayed.

Application Drawings: Routing across the WAN
Revision C Page 18 of 27
7. Check the box next to "Enable", to enable the interface.

Application Drawings: Routing across the WAN
Revision C Page 19 of 27
8. Select "1" in the “Data DS0s” drop down list and "24" in the second drop down.

Application Drawings: Routing across the WAN
Revision C Page 20 of 27
9. Choose "PPP" from the "Encapsulation" options.