ADTRAN 1200422L1 Manual

NetVanta 300 Series
Hardware Installation Guide
1200422L1 NetVanta 340
1200423E1/L1 NetVanta 344 Annex B
1200426E1/L1 NetVanta 344 Annex A
1200429L1 NetVanta 347
61200422L1-34D
July 2006

Trademarks NetVanta 300 Series Hardware Installation Guide
2 Copyright © 2006 ADTRAN, Inc. 61200422L1-34D
Trademarks
Any brand names and product names included in this manual are trademarks, registered trademarks, or
trade names of their respective holders.
To the Holder of the Manual
The contents of this manual are current as of the date of publication. ADTRAN reserves the right to change
the contents without prior notice.
In no event will ADTRAN be liable for any special, incidental, or consequential damages or for
commercial losses even if ADTRAN has been advised thereof as a result of issue of this publication.
Software Licensing Agreement
Each ADTRAN product contains a single license for ADTRAN supplied software. Pursuant to the
Licensing Agreement, you may: (a) use the software on the purchased ADTRAN device only and (b) keep
a copy of the software for backup purposes. This Agreement covers all software installed on the system as
well as any software available on the ADTRAN website. In addition, certain ADTRAN systems may
contain additional conditions for obtaining software upgrades.
901 Explorer Boulevard
P.O. Box 140000
Huntsville, AL 35814-4000
Phone: [phone]
Copyright © 2006 ADTRAN, Inc.
All Rights Reserved.
Printed in U.S.A.
Changes or modifications to this unit not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment.

NetVanta 300 Series Hardware Installation Guide Conventions
61200422L1-34D Copyright © 2006 ADTRAN, Inc. 3
Conventions
Notes provide additional useful information.
Cautions signify information that could prevent service interruption or damage to
equipment.
Warnings provide information that could prevent injury or endangerment to human
life.

Safety Instructions NetVanta 300 Series Hardware Installation Guide
4 Copyright © 2006 ADTRAN, Inc. 61200422L1-34D
Safety Instructions
When using your telephone equipment, please follow these basic safety precautions to reduce the risk of
fire, electrical shock, or personal injury:
1. Do not use this product near water, such as a bathtub, wash bowl, kitchen sink, laundry tub, in a
wet basement, or near a swimming pool.
2. Avoid using a telephone (other than a cordless-type) during an electrical storm. There is a remote
risk of shock from lightning.
3. Do not use the telephone to report a gas leak in the vicinity of the leak.
4. Use only the power cord, power supply, and/or batteries indicated in the manual. Do not dispose of
batteries in a fire. They may explode. Check with local codes for special disposal instructions.
5. The socket-outlet shall be installed near the equipment and shall be easily accessible.
Save These Important Safety Instructions

NetVanta 300 Series Hardware Installation Guide FCC-Required Information
61200422L1-34D Copyright © 2006 ADTRAN, Inc. 5
FCC-Required Information
FCC regulations require that the following information be provided in this manual:
1. This equipment complies with Part 68 of FCC rules and requirements adopted by ACTA. Each
registered interface has a label that contains, among other information, a product identifier in the
format US:AAAEQ##TXXXX. If requested, provide this information to the telephone company.
2. If this equipment causes harm to the telephone network, the telephone company may temporarily
discontinue service. If possible, advance notification is given; otherwise, notification is given as
soon as possible. The telephone company will advise the customer of the right to file a complaint
with the FCC.
3. The telephone company may make changes in its facilities, equipment, operations, or procedures
that could effect the proper operation of this equipment. Advance notification and the opportunity
to maintain uninterrupted service are given.
4. If experiencing difficulty with this equipment, please contact ADTRAN for repair and warranty
information. The telephone company may require this equipment to be disconnected from the
network until the problem is corrected or it is certain the equipment is not malfunctioning.
5. This unit contains no user-serviceable parts.
6. This equipment is designed to connect to the telephone network or premises wiring using an
FCC-compatible modular jack, which is compliant with Part 68 and requirements adopted by
ACTA.
7. The following information may be required when applying to the local telephone company for
leased line facilities:
8. The REN is useful in determining the quantity of devices you may connect to your telephone line
and still have all of those devices ring when your number is called. In most areas, the sum of the
RENs of all devices should not exceed five. To be certain of the number of devices you may
connect to your line as determined by the REN, call your telephone company to determine the
maximum REN for your calling area.
9. This equipment may not be used on coin service provided by the telephone company. Connection
to party lines is subject to state tariffs. Contact your state public utility commission or corporation
commission for information.
Part Number Registration Number Service Type REN/SOC FIC USOC
1200422L1
1200429L1 US: HDCDL01A1200422L1 ADSL 0.1A/9.0F 02LS2 RJ-11C
1200426E1/L1 US: HDCDL01A1200426L1 ADSL 0.1A/9.0F 02LS2 RJ-11C

FCC Radio Frequency Interference Statement NetVanta 300 Series Hardware Installation Guide
6 Copyright © 2006 ADTRAN, Inc. 61200422L1-34D
FCC Radio Frequency Interference Statement
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant
to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses, and can radiate radio frequency
energy and, if not installed and used in accordance with the instruction manual, may cause harmful
interference to radio communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

NetVanta 300 Series Hardware Installation Guide Industry Canada Compliance Information
61200422L1-34D Copyright © 2006 ADTRAN, Inc. 7
Industry Canada Compliance Information
The Industry Canada label applied to the product (identified by the Industry Canada logo or the “IC:” in
front of the certification/registration number) signifies that the Industry Canada technical specifications
were met.
The Ringer Equivalence Number (REN) for this terminal equipment is supplied in the documentation or on
the product labeling/markings. The REN assigned to each terminal device indicates the maximum number
of terminals that can be connected to a telephone interface. The termination on an interface may consist of
any combination of devices subject only to the requirement that the sum of the RENs of all the devices
should not exceed five (5).
Canadian Emissions Requirements
This digital apparatus does not exceed the Class B limits for radio noise emissions from digital apparatus
as set out in the interference-causing equipment standard entitled “Digital Apparatus,” ICES-003 of the
Department of Communications.
Cet appareil numérique respecte les limites de bruits radioelectriques applicables aux appareils numériques
de Class A prescrites dans la norme sur le materiel brouilleur: “Appareils Numériques,” NMB-003 edictee
par le ministre des Communications.

Warranty NetVanta 300 Series Hardware Installation Guide
8 Copyright © 2006 ADTRAN, Inc. 61200422L1-34D
Warranty
ADTRAN will repair and return this product within the warranty period if it does not meet its published
specifications or fails while in service. Warranty information can be found in the Support section of the
ADTRAN website at http://www.adtran.com.
Product Registration
Registering your product helps ensure complete customer satisfaction. Please take time to register your
products in the Support section of the ADTRAN website at http://www.adtran.com
Product Support Information
A return material authorization (RMA) is required prior to returning equipment to ADTRAN. For service,
RMA requests, training, or more information, use the contact information shown below.
Repair and Return
If you determine that a repair is needed, please contact our Customer and Product Service (CaPS)
department to have an RMA number issued. CaPS should also be contacted to obtain information
regarding equipment currently in house or possible fees associated with repair.
Identify the RMA number clearly on the package (below the address), and return to the following address:
Pre-Sale Inquiries and Applications Support
Your reseller should serve as the first point of contact for support. If additional pre-sales support is needed,
the ADTRAN Support website provides a variety of support services such as a searchable knowledge base,
the latest product documentation, application briefs, case studies, and a link to submit a question to an
Applications Engineer. All of this, and more, is available in the Support section of the ADTRAN website at
http://www.adtran.com.
When needed, further pre-sales assistance is available by calling our Applications Engineering
Department.
CaPS Department [phone]
ADTRAN Customer and Product Service
901 Explorer Blvd. (East Tower)
Huntsville, Alabama 35806
RMA # _____________
Applications Engineering [phone]

NetVanta 300 Series Hardware Installation Guide Product Support Information
61200422L1-34D Copyright © 2006 ADTRAN, Inc. 9
Post-Sale Support
Your reseller should serve as the first point of contact for support. If additional support is needed, the
ADTRAN website provides a variety of support services such as a searchable knowledge base, updated
firmware releases, latest product documentation, service request ticket generation and trouble-shooting
tools. All of this, and more, is available in the Support section of the ADTRAN website at
http://www.adtran.com.
When needed, further post-sales assistance is available by calling our Technical Support Center. Please
have your unit serial number available when you call.
Installation and Maintenance Support
The ADTRAN Custom Extended Services (ACES) program offers multiple types and levels of installation
and maintenance services which allow you to choose the kind of assistance you need. This support is
available at:
For questions, call the ACES Help Desk.
Training
The Enterprise Network (EN) Technical Training Department offers training on our most popular products.
These courses include overviews on product features and functions while covering applications of
ADTRAN's product lines. ADTRAN provides a variety of training options, including customized training
and courses taught at our facilities or at your site. For more information about training, please contact your
Territory Manager or the Enterprise Training Coordinator.
Technical Support (888) 4ADTRAN
International Technical Support 1-256-963-8716
http://www.adtran.com/aces
ACES Help Desk (888) 874-ACES (2237)
Training Phone [phone], ext. 7500
Training Fax [phone]
Training Email [e-mail]

Product Support Information NetVanta 300 Series Hardware Installation Guide
10 Copyright © 2006 ADTRAN, Inc. 61200422L1-34D