ADTRAN Total Access 5000 User manual

Q
uic
k
Start
DESCRIPTION
The Total Access 5000 2.5G/1.25G, Class C+ SFP for GPON OLT
(Small Form-factor Pluggable) is specifically designed for the
Gigabit Passive Optical Network (GPON) Optical Line Terminal
(OLT) application. It facilitates high performance, integrated,
bidirectional data transmission over one, single mode optical fiber.
The 2.5G/1.25G, Class C+ SFP for GPON OLT can be used with
the following Total Access 5000 OLTs:
■4-Port OLT (P/N 1187502F2)
■8-Port 2nd Generation OLT (P/N 1187503F2)
The SFP incorporates a 1490 nm, DFB laser diode for streaming
2.488 Gbps downstream data and an APD/TIA burst mode
receiver for 1310 nm 1.244 Gbps upstream data.
gNOTE
To ensure compatibility, refer to the documentation provided with
the host module.
FEATURES
The following features are supported on the SFP:
■SC Simplex receptacle
■Hot pluggable
■Transmit wavelength: 1490 nm
■Receive wavelength: 1310 nm
f
CAUTION!
Due to compliance certification requirements, only SFPs supplied
by ADTRAN are to be used with the host module. ADTRAN
cannot certify system integrity with other SFPs.
INSTALLATION
Before installation, inspect the SFP. If damage has occurred
during shipping, file a claim with the carrier and then contact
ADTRAN Customer Support. For more information, refer to
“Warranty”.
Installation Guidelines
The following are guidelines for this installation.
■The latch on the SFP is for removal only. When removing the
SFP, rotate the latch away from the SFP. The SFP should slide
easily out of the cage.
■It is recommended that the connector plug remain on
whenever the transceiver optical fiber connector is not
inserted.
Installation Steps
To install the SFP, complete the following steps:
1. Insert the SFP into the SFP cage on the circuit board of the
host module with the latch handle facing outward. Slide the
SFP all the way into the cage.
2. Exert adequate pressure to ensure the SFP is completely
seated in the SFP cage.
3. Do not remove the connector plug until the optical fiber
connection is made.
4. Continue the installation and turn-up of the host module.
SPECIFICATIONS
Specifications for the SFP are as follows:
■Optical:
♦Receive wavelength: 1310 nm
♦Transmit wavelength: 1490 nm
♦Data rate:
●Receive: 1.244 Gbps
●Transmit: 2.488 Gbps
♦Receiver sensitivity (without upstream FEC):
less than –30.0 dBm
♦Receiver sensitivity (with upstream FEC):
less than –32.0 dBm (requires FEC support at both
ONT and OLT)
♦Optical transmit level: 3.0 dBm to 7.0 dBm
♦Optical connectors: SC
■Environmental
♦Operational temperature range: –40°C to +65°C
♦Storage temperature range: –40°C to +85°C
♦Relative humidity to 95%, non-condensing
Small Form-factor Pluggable
SFP
2.5G/1.25G, Class C+ SFP for GPON OLT
September 2017
61442540F1-13A
1442540F1

gNOTE
■This product is designed to be deployed in GR-3108-CORE
environmental Class 1, 2, & 3.
■This product meets EU RoHS Directive. Refer to
www.adtran.com for further information on RoHS/WEEE.
■This product is designed to function without degradation during
exposure to all test severities per Class 3.3.
■This device complies with Part 15 of the FCC rules. Operation
is subject to the following two conditions:
1. This device may not cause harmful interference.
2. This device must accept any interference received, including
interference that may cause undesired operation.
■Changes or modifications not expressly approved by ADTRAN
could void the user's authority to operate this equipment.
SAFETY AND REGULATORY
fWARNING!
Read all warnings and cautions before installing or servicing this
equipment.
CCAUTION!
This product is a Class 1 Laser that complies with FDA 21 CFR
1040.10 and 1040.11 and IEC 60825-1 and -2. The product is
NRTL Listed and CB Certified to all applicable American and
European safety standards.
f
CAUTION!
Electrostatic Discharge (ESD) can damage electronic modules.
When handling modules, wear an antistatic discharge wrist strap
to prevent damage to electronic components. Place modules in
antistatic packing material when transporting or storing. When
working on modules, always place them on an approved antistatic
mat that is electrically grounded.
f
CAUTION!
■The GPON OLT meets or exceeds all the applicable
requirements of NEBS, Telcordia GR-63-CORE, and GR-
1089-CORE. The this product is intended for deployment in
Central Office type facilities, EEEs, EECs, and locations where
the NEC applies (for example, Customer Premises). This
product is to be installed in ADTRAN products in Restricted
Access Locations only, and installed by trained service
personnel.
■Per GR-1089-CORE, the ADTRAN system that this product is
being deployed in is designed and intended for installation as
part of a Common Bonding Network (CBN). The ADTRAN
system that this product is being deployed in is not designed
nor intended for installation as part of an Isolated Bonding
Network (IBN).
■This product is intended to operate in ambient temperatures up
to 65°C.
■Per GR-1089-CORE Section 9, this product does not have an
internal DC connection between battery return and frame
ground. This product can be installed in a DC-I (isolated) or
DC-C (common) installation. For installations where other
cards or the host system have internal connections between
battery return and frame ground, the system would be
intended for deployment only in a DC-C installation.
■The ADTRAN system chassis frame ground terminal must be
connected to a reliable earth ground to ensure that the metal
enclosure of this product is properly grounded via the
backplane connector.
CAUTION!
SUBJECT TO ELECTROSTATIC DAMAGE
OR DECREASE IN RELIABILITY
HANDLING PRECAUTIONS REQUIRED
Warranty: ADTRAN will replace or repair this product within the warranty period if it does not
meet its published specifications or fails while in service. Warranty information can be
found online at www.adtran.com/warranty.
Trademarks: Brand names and product names included in this document are trademarks,
registered trademarks, or trade names of their respective holders.
©2017 ADTRAN, Inc. All Rights Reserved.
ADTRAN CUSTOMER CARE:
From within the U.S. 1.888.423.8726
From outside the U.S. +1 256.963.8716
PRICING AND AVAILABILITY 1.800.827.0807
*61442540F1-13A*
Documentation for ADTRAN Network Solutions products is available for
viewing and download directly from the ADTRAN Support Community
website.
Go to: https://supportforums.adtran.com/welcome
Registration is required.
ADTRAN offers training courses on our products, including customized
training and courses taught at our facilities or at customer sites.
For inquiries, go to: http://adtran.com/training
The following online documents and resources provide additional information for this product:
ADTRAN Pluggable Optics Compatibility Matrix (online tool, go to: http://www.adtran.com/
pluggableoptics)