NCR RealPOS 7460-2 Manual

NCR RealPOS 7460-2xxx
Release 2.0
Site Preparation
200
B005-0000-1480
Issue A

The products described in this book are licensed products of NCR Corporation.
NCR is a registered trademark of NCR Corporation.
NCR RealPOS is a trademark of NCR Corporation in the United States and/or other countries.
Pentium is a registered trademark of Intel Corporation.
It is the policy of NCR Corporation (NCR) to improve products as new technology, components, software,
and firmware become available. NCR, therefore, reserves the right to change specifications without prior
notice.
All features, functions, and operations described herein may not be marketed by NCR in all parts of the
world. In some instances, photographs are of equipment prototypes. Therefore, before using this document,
consult with your NCR representative or NCR office for information that is applicable and current.
To maintain the quality of our publications, we need your comments on the accuracy, clarity, organization,
and value of this book.
Written by Joseph N. Cole III
Address correspondence to:
Manager, Information Products
NCR Corporation
2651 Satellite Blvd.
Duluth, GA 30096
Copyright © 2002
By NCR Corporation
Dayton, Ohio U.S.A.
All Rights Reserved

i
Preface
This is a contractual document. It contains important warnings and
confers important legal rights and obligations. You are advised to read
it carefully.
It is the responsibility of the customer to assure that all installation
preparations are complete and in compliance with NCR specifications
and requirements and all applicable national, state, or local codes,
regulations, and laws.
Safety Requirements
The operator must connect this web kiosk to an AC outlet that is near
the terminal and is easily accessible.
Warning: This unit contains hazardous voltages and should only be
serviced by qualified service personnel.
The AC line voltage primaries are live at all times when the power cord
is connected. Therefore, disconnect the AC power cord before opening
the unit to install features or service this web kiosk.
Peripheral Usage
This web kiosk should be used only with peripheral devices that are
recommended by NCR Corporation and are certified by the
appropriate safety agency for the country of installation (UL, CSA,
TUV and VDE).

ii
About this Book
This book provides site preparation information for terminal
components. Peripheral component and AC wiring site preparation
information is NOT provided in this book. The associated reference
documents are listed in the “Related Site Preparation Data” section.
This book contains the information necessary for the preparation of a
site that conforms to NCR specifications. It is very important that the
site complies with the requirements specified in the document because,
once the equipment has been installed, deficiencies in site preparation
or the problems caused by these deficiencies are much more difficult to
detect and correct. Further, failure to comply with these requirements
or to take proper steps to protect equipment against risks identified in
this document may cause serious damage to the equipment and to the
customer’s business.
In addition to the need to comply with the requirements specified,
electrical wiring and mechanical systems must also comply with all
relevant codes, laws, and regulations.
It is important that a customer or his agent who is fully conversant
with the special requirements of electronic equipment prepare the site.
The responsibility of ensuring that the site is prepared in compliance
with this document remains with the customer.
For information and guidance purposes only, a list is provided, in
general terms, of those matters for which the customer is responsible.
This list is not intended to be comprehensive, and in no way modifies,
alters, or limits the responsibility of the customer for all aspects of
adequate site preparation.
NCR staff will be available to answer questions relating to the contents
of this document except where:
•A customer has been notified that a full or partial consultant service
is available and/or that NCR will be willing to undertake a
preliminary or final site survey and
•The customer shall have entered into a formal contract with NCR
for provision of the same.

iii
No comment, suggestion, or advice offered or not offered about
preparation of the site, nor any inspection of the site, whether before of
after preparation, is to be taken as approval of the location of the site
and equipment or its preparation. NCR will not be liable in respect to
any comment, suggestion, or advice given by its staff or in respect to
any failure to give advice.
Finally, only the customer can know the full extent of damage that may
be caused to his business by reason of failure of the equipment which is
to be installed. For this reason, it is the customer’s responsibility to
ascertain the extent of any possible damage to his existing or planned
business, and to effect full insurance in for all eventualities.

iv
References
•NCR RealPOS 7460-2xxx Site Preparation Guide
(B005-0000-1480)
•NCR RealPOS 7460-2xxx Hardware Service Guide
(B005-0000-1482)
•NCR RealPOS 7460-2xxx Parts Identification Manual
(B005-0000-1483)

v
Table of Contents
Introduction 1
Customer Responsibilities .................................................2
Where to Obtain Information Products ...........................3
AC Store Wiring Requirements ........................................3
LAN Communications .......................................................3
System Configuration Diagrams 4
Dimensions 5
7460 Terminal ......................................................................5
2183 Cash Drawer ...............................................................6
2189 Cash Drawer ...............................................................6
7197 Thermal Receipt Printer ............................................7
7167 Thermal Receipt/Impact Printer .............................7
7196 Thermal Receipt Printer ............................................8
5973 International VFD Customer Display ...................10
2336-K007 External CD-ROM Drive...............................11
Component Weights 12
Ventilation Clearance 13
Power Requirements 14
Maximum Input Power Specifications ....................14
Power Analysis for Terminal and Peripherals .......15
Cable Routing Considerations 16
Cables 17

vi
Printers ...............................................................................19
7167, 7197 Printer (RS-232)........................................19
7167, 7197 Printer (USB) ............................................19
7196 Printer (RS-232) ........................................................20
Cash Drawers ....................................................................21
Cash Drawer, Extension Cable .................................21
PS/2 Y-Cable .....................................................................21
5964 to 7460 (RS-232/PS2/Power) .................................22
Remote Customer Displays .............................................22
5972 VFD (Parallel).....................................................22
5972 VFD (RS-232)......................................................23
5973/5974 VFD (Parallel) ..........................................23
Operator Display Cable (DVI to DVI)............................24
5945/5992 Cable (RS-232) ................................................24
Communications Cable....................................................25
Ethernet, 10/100BaseT...............................................25
Power Cables .....................................................................25
AC Power.....................................................................25
Environmental Requirements 26
Barometric Pressure..........................................................26
Temperature ......................................................................26
Humidity............................................................................26
AC Power Line Transient Protection 1
Data Line Transient Protection 2

vii
Revision Record
Issue Date Remarks
A Sept 02 First issue

viii
Radio Frequency Interference Statements
Federal Communications Commission (FCC)
Information to User
This equipment has been tested and found to comply with the limits for a Class A
digital device, pursuant to Part 15 of FCC Rules. These limits are designed to provide
reasonable protection against harmful interference when the equipment is operated in
a commercial environment. This equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in accordance with the instruction
manual, may cause harmful interference to radio communications. Operation of this
equipment in a residential area is likely to cause interference in which case the user
will be required to correct the interference at his own expense.
NCR is not responsible for any radio or television interference caused by unauthorized
modification of this equipment or the substitution or attachment of connecting cables
and equipment other than those specified by NCR. The correction of interference
caused by such unauthorized modification, substitution or attachment will be the
responsibility of the user. The user is cautioned that changes or modifications not
expressly approved by NCR may void the user’s authority to operate the equipment.
Canadian Department of Communications
This digital apparatus does not exceed the Class A limits for radio noise emissions
from digital apparatus set out in the Radio Interference Regulations of the Canadian
Department of Communications.
Le présent appareil numérique n’émet pas de bruits radioélectriques dépassant les
limites applicables aux appareils numériques de la classe A prescrites dans le
Règlement sur le brouillage radioélectriques édicté par le ministrère des
Communications du Canada.
Voluntary Control Council for Interference (VCCI)

ix
Declaration of Conformity
Manufacturer's Name NCR Corporation
Manufacturer's Address NCR Corporation
Retail Solutions Division— Atlanta
2651 Satellite Boulevard
Duluth, GA 30096-5810
Type of Equipment Information Technology Equipment
Model Number Class 7460
Electrical Ratings (Input) 100-120 V/200-240 V, 4.0 A/2.0 A, 50-60 Hz
NCR Corporation, 1700 South Patterson Boulevard, Dayton, OH 45459,
USA, declares that the equipment specified above conforms to the
referenced EU Directives and Harmonized Standards.
EU Directive Harmonized Standard(s)
89/336/EEC (EMC) EN 55022: 1987 (CISPR 22)
EN 50082-1, Part 1: 1992
IEC 801-2: 1984
IEC 801-3: 1984
IEC 801-4: 1988
73/23/EEC (Low Voltage) EN 60 950: +A1+A2: +A3 + A11
NCR Corporation
Retail Solutions Division— Atlanta
2651 Satellite Boulevard
Duluth, GA 30096-5810
European Contact:
International IP Counsel
206 Marylebone Road
London, NW1 6LY, England

x

Introduction
20084
This document provides the information necessary to prepare a site to
NCR specifications prior to installing a terminal. The site must be
properly prepared before the terminal is installed because site
preparation deficiencies may be difficult to detect and correct after
installation.
The terminal consists of separate pieces that may be combined in a
variety of configurations. Certain combinations are mutually exclusive.
You must determine the equipment that will actually be installed
before proceeding with the site preparation.

2 NCR 7460 Terminal Site Preparation
Customer Responsibilities
Before the system can be installed, the customer must do or provide the
following:
•When required by NCR, provide the NCR Customer Services
representative with appropriate drawings that indicate:
−Location of the equipment
−Site wiring (power and communications, paths and lengths)
−Location of other equipment that may generate electrical noise,
electromagnetic interference, or heat.
•Make building alterations necessary to meet wiring and other site
requirements
•Provide and install all communications cables, wall jacks, special
connectors, and associated hardware
•Provide and install necessary power distribution boxes, conduits,
grounds, lightning protection devices, and associated hardware
•Make sure all applicable codes, regulations, and laws (including,
but not limited to, electrical, building, safety, and health) are met
•Provide and install auxiliary power or other equipment as required
•Provide storage or service areas as required
•Meet all system/unit environmental requirements
•Provide and install floor coverings and environmental systems that
limit or control static electricity build-up and discharge
In general, keep the NCR equipment area free from dust, smoke, lint,
and other particles. Restrict smoking, eating, and drinking around the
equipment. Avoid locating the equipment near other machines that
generate ink, carbon, and paper dust particles.
Finally, only the customer can know the full extent of the damage that
may be caused to his business by reason of failure of the equipment
that is to be installed. For this reason, it is the customer's responsibility
to ascertain the extent of any such possible damage to his existing or
planned business, and to effect full insurance for all eventualities.

NCR 7460 Terminal Site Preparation 3
Where to Obtain Information Products
Information Products are available in electronic format from the
following web sites.
Web Sites
•http://www.info.NCR.COM (World Wide Web)
•http://inforetail.AtlantaGA.NCR.COM (NCR Intranet)
AC Store Wiring Requirements
The customer must provide suitable AC power for the web kiosks,
associated equipment, and devices. A dedicated unswitched power
line dedicated to the NCR equipment installation is recommended.
Refer to the Workstation and Peripherals AC Wiring Guide (BSTO-
2115-53) for store AC wiring requirements. The AC outlet must be
installed near the web kiosk and easily accessible to the operator.
LAN Communications
The terminal supports Ethernet 10/100 Base local area network (LAN)
communication protocol. For Ethernet communications wiring
specifications, refer to the NCR Ethernet Wiring Guide (BST0-2118-82).

4 NCR 7460 Terminal Site Preparation
System Configuration Diagrams
20128
LAN
Ethernet
7460-20xx
5992
Signature
Capture
Terminal
5945
Electronic
Payment
Terminal
Transaction Printers
Parallel
PS/2
KBD
7197
7892
Presentation
Scanner
2189
Cash
Drawer
RS-232
Keyboard 5973 2 x 20
Customer Display
USB
7167
2183
TELEQIP
Coin Dispenser
2336-K022
5974 4 x 20
Customer Display
7196

NCR 7460 Terminal Site Preparation 5
Dimensions
7460 Terminal
20129
250 mm
(9.75 in.)
28 o
90 o
325 mm
(12.75 in.)
350 mm
(13.75 in.)
292 mm
(12 in.)
382 mm
(15.0 in.)

6 NCR 7460 Terminal Site Preparation
2183 Cash Drawer
18038
455 mm
(17.9 in.)
108 mm
(4.25 in.)
450 mm
(17.7 in.)
Operating and Service
Clearance for Drawer
263 mm
(10.4 in.)
2189 Cash Drawer
16676a
133 mm
(5.25 in.)
330 mm
(13 in.)
(18.25 in.)
Operating and
Service Clearance
for Drawer
464 mm
527 mm
(20.5 in.)

NCR 7460 Terminal Site Preparation 7
7197 Thermal Receipt Printer
19712d
146 mm
(7.75 in.)
156 mm
(6.25 in.)
184 mm
(7.25 in.)
Top Cover Open
256 mm
(10.1 in.)
7167 Thermal Receipt/Impact Printer
19711d
190 mm
(7.5 in.)
174 mm
(7.0 in.)
262 mm
(10.3 in.)
316 mm
(12.5 in.)
Top Cover Open
296 mm
(11.7 in.)

8 NCR 7460 Terminal Site Preparation
7196 Thermal Receipt Printer
108 mm
(4.25 in.)
140 m
(5.50 in.)
146 mm
(5.75 in.) 254 mm
(10.00 in.)
17306